FOCUSED FTS20204 User manual

FTS20204
Battery-Operated Lag Driver
Operation Manual
www.FocusedTS.com 973-705-7170 customer[email protected]

FTS20204 - Battery Operated Lag Driver
TABLE OF CONTENTS
SAFETY SYMBOLS 2
SAFETY PRECAUTIONS 3
TOOLS STICKERS & TAGS 4
OPERATION 4
MAINTENANCE & TROUBLESHOOTING 5
SPECIFICATIONS 6
DRILL TYPE 6
ACCESSORIES 6
WARRANTY 6-7
IMPORTANT
To fill out a Product Warranty Recording form, and for information on your warranty, call FTS at [phone]
and request the Warranty form or have your Warranty assigned number ready. (NOTE: The warranty recording
form must be submitted to validate the warranty).
SERVICING: This manual contains safety, operation, and routine maintenance instructions. Focused recommends
that servicing of battery powered tools, other than routine maintenance, must be performed by an authorized
and certified dealer. Please read the following warning.
For the nearest authorized and certified dealer, call FocusedTS at 973-705-7187 and ask for a Customer Service
Representative. For our Terms and Conditions and any other information, visit our WebPage www.FocusedTS.com.
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
1

FTS20204 - Battery Operated Lag Driver
SAFETY SYMBOLS
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair
actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to
equipment.
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
2

FTS20204 - Battery Operated Lag Driver
SAFETY PRECAUTIONS
Tool operators and maintenance personnel must always comply with the safety precautions given in this manual
and on the stickers and tags attached to the tool. These safety precautions are given for your safety. Review them
carefully before operating the tool and before performing general maintenance or repairs. Supervising personnel
should develop additional precautions relating to the specific work area and local safety regulations. If so, place
the added precautions in the space provided in this manual. This tool will provide dependable service if operated
in accordance with the instructions given in this manual. Read and understand this manual and any stickers and
tags attached to the tool before operation. Failure to do so could result in personal injury or equipment damage.
•Inspect work area prior to operation of tool and ensure safe distances maintained with tool and any spectators.
• Only thoroughly trained workers may operate the tool. Exception is for operators under the guidance of a
trainer. All operators must follow its own company’s established training program to ensure safe operation.
•Always wear the following safety equipment when operating the tool: ear protection, gloves, safety goggles,
head protection, and safety shoes.
• The operator must avoid operation of the tool in treacherous situations, such as steep slopes, dangerous
terrain and other prohibited conditions.
• Maintain proper footing and balance at all times. Do not overextend.
•Disconnect battery source from tool prior to inspection or cleaning. Accidental engagement of the tool may
cause serious injury.
• Do not operate a damaged, improperly adjusted, or incompletely assembled tool.
• Never wear loose clothing that can get entangled in the working parts of the tool.
• Do not modify the tool in any way.
•Only use accessories that conform to the specifications given in the OPERATION section of this manual.
• All tool repair, maintenance and service must only be performed by authorized and properly trained personnel
to avoid personal injury or equipment damage.
• Only use the tool as specified for its intended purpose.
• Always hold the tool firmly with both hands on the handles when the unit is running.
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
3

FTS20204 - Battery Operated Lag Driver
TOOLS STICKERS & TAGS
Focused Technology LagEase - Logo Decal –All-In-One Product Label-FTS20204-CPD01
Focused Technology LagEase - Tool Logo Decal-FTS20204-CPD02
Focused Technology LagEase - Focused Technology Contact Information Decal-FTS20204-CPD03
Focused Technology LagEase- Focused Technology Solutions U.S.A. Decal- FTS20204-CPD04
NOTE: THE INFORMATION LISTED ON THE STICKERS SHOWN, MUST BE LEGIBLE AT ALL TIMES. REPLACE DECALS
IF THEY BECOME WORN OR DAMAGED. REPLACEMENTS ARE AVAILABLE FROM YOUR LOCAL FocusedTS
DISTRIBUTOR. A REPLACEMENT FEE MAY BE INCURRED.
OPERATION
PRE-OPERATION SAFETY INSPECTION
CHECK BATTERY POWER SOURCE 1. Make sure the battery is fully charged. 2. Remove battery prior to inspecting
the tool.
CHECK TOOL 1. Make sure all tool accessories are correctly installed. Failure to install tool accessories properly
can result in damage to the tool or personal injury. 2. There should be no signs of damage or missing parts. 3.
The tool should be clean, with no loose or missing parts.
CHECK TRIGGER MECHANISM 1. Check that the trigger operates smoothly.
BEFORE DRIVING SCREW SPIKES/LAGS 1. Make sure the tool runs freely in both directions.
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
4

FTS20204 - Battery Operated Lag Driver
OPERATING PROCEDURES
1. Observe all safety precautions (see page 3).
2. Ensure the battery is installed.
3. To drive a screw spike/lag, make sure the tool is operating in a clockwise direction. Press the direction button
forward away from the user and toward the ground.
5. To remove the screw spike/lag, make sure the tool is operating in a counter-clockwise direction. Press the
direction button backward toward the user and away from the ground.
5. Ensure that Agency’s safety procedures are followed when working around or near the third rail.
6. Make sure drill is set to #4. Sometimes hands may accidentally reset to a lower setting.
7. Center the tool over the screw spike/lag until the screw spike/lag sits inside the socket at the end of the
LagEase.
8. Let the tool do the work. Do not exert pressure on the tool with your body weight to assist with driving the
screw spike/lag.
9. Remove the battery from the tool when not in use. Never inspect the unit with the battery installed.
COLD WEATHER OPERATION Using the LagEase during cold weather may reduce the charge life of the battery.
DAILY MAINTENANCE
1. Make sure that the socket retainer is firmly in place holding the socket to the LagEase.
Note: Any major repair(s) must be performed by an authorized and certified dealer. Call 973-705-7187.
TROUBLESHOOTING
If symptoms of poor performance develop, the following points can be used as a guide to correct the problem.
When diagnosing faults in operation of the lag driver, always check the battery power source and battery charge
level.
Problem:
Solution:
Lag Driver will not operate
Check the direction button to be sure it is not set on
the lock setting
Lag Driver operates slowly
Check for low battery level and replace the battery.
Make sure it is set to #4.
*NEVER ACCESS UNIT WITH BATTERY ENGAGED
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
5

FTS20204 - Battery Operated Lag Driver
●Always store the tool in a clean, dry space, safe from damage or pilferage. Also, ensure the battery is
disengaged and not on the tool.
●Do not exceed the rated limits or use of the tool for applications beyond its designed capacity. (see
manual)
●Always keep critical tool markings, such as labels and warning stickers legible.
●Permit only authorized and certified dealers to perform tool repair.
SPECIFICATIONS
Weight - 10 lbs Tool only. Under 35lbs. with wrench and 12 ah battery
Battery - M18™ REDLITHIUM™ HIGH OUTPUT™ HD12.0
Overall Length - 20”
Handle Height - 10”
DRILL TYPE
M18 FUEL 18-Volt Lithium-Ion Brushless Cordless 1 in. Impact Wrench with D-Handle
(FTS20204-MW286820)
ACCESSORIES
12.0 ah battery - FTS20182-75
Rapid charger - FTS20182-84
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
6

FTS20204 - Battery Operated Lag Driver
LagEase Warranty (less drill)
LIMITED WARRANTY
Focused Technology Solutions manufactured products purchased in the U.S., Canada, Australia, or Europe come
with a limited warranty; if properly used and installed, will be free from defects in material and workmanship for a
period of 90 days after the date of purchase. The warranty period is not extended if we repair or replace a
warranted product or any parts. Said warranty to include the repair or replacement of defective parts or equipment
only.
Legislation requires that all protective equipment be tested at least once a year for compliance with Focused
Technology Solutions specifications and to industry standards. Ensuring your safety equipment meets or exceeds
the highest standards reduces the costs of lost-time accidents. Focused Technology Solutions independent
testing facilities used are fully industry compliant.
Call 973-705-7187 for “Service and Support” for Service and Maintenance contracts Focused Technology
Solutions offers to the customers. We strongly recommend this service to all our customers.
What is not covered by this limited warranty?
This limited warranty does not cover:
Components manufactured by other parties, damage due to external causes, including accident,
problems with electrical power, and usage not in accordance with product instructions, misuse, neglect,
alteration, repair by unauthorized persons, improper installation, or improper testing and improper
operating procedures.
This limited warranty does not cover batteries or rechargeable batteries.
THIS LIMITED WARRANTY, AND ANY IMPLIED WARRANTIES THAT MAY EXIST UNDER STATE LAW, APPLY
ONLY TO THE ORIGINAL PURCHASER OF THE EQUIPMENT, AND LAST ONLY FOR AS LONG AS SUCH
PURCHASER CONTINUES TO OWN THE EQUIPMENT. THIS WARRANTY REPLACES ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FOCUSED TECHNOLOGY SOLUTIONS
MAKES NO EXPRESS WARRANTIES BEYOND THOSE STATED HERE. FOCUSED TECHNOLOGY
SOLUTIONS DISCLAIMS WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES, SO THIS LIMITATION MAY NOT APPLY TO YOU.
TO OBTAIN WARRANTY SERVICE, CONTACT FOCUSED TECHNOLOGY SOLUTIONS FOR A RETURN
MATERIAL AUTHORIZATION. WHEN RETURNING EQUIPMENT TO FOCUSED TECHNOLOGY SOLUTIONS,
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
7

FTS20204 - Battery Operated Lag Driver
THE CUSTOMER ASSUMES THE RISK OF DAMAGE OR LOSS DURING SHIPPING AND IS RESPONSIBLE
FOR THE SHIPPING COSTS INCURRED.
Drill Warranty:
See drill manufacturer’s standard warranty.
FTS20204 Operation Manual 1-13-21
973.705.7170
www.FocusedTS.com
[e-mail]
8