Follett HCD1650RBT User manual

Horizon™
remote 1650 series Chewblet® ice machine
Short form specification:
Ice machine to be a Follett® Horizon Chewblet ice machine model
________________ [Insert size/series,condenser type and installation/
mounting, from model number guide] capable of producing compressed
nugget ice using an ecient, sanitary horizontal evaporator/auger system
and delivering ice by a flexible wire reinforced transport tube to ice
storage bin, iceand water dispenser, ice and beverage dispenser,
drop-in dispenser or Ice Manager™ diverter valve system and provided
with a stainless steel frame and exterior, slide-out evaporator unit with
utility docking station, front-mounted unit status display, automatic
self-flush, and semi-automatic cleaning and sanitizing system, plusall the
featureslisted below and mounting/performance-enhancing accessories
checked:
Horizon remote 1650 series ice machine
For use with
1Install/mount Condenser V/Hz/Ph Item number
ice storage bin
top mount
with 115/60/1 HCD1650RBT
without 115/60/1 HCD1650NBT
RIDE
with 115/60/1 HCD1650RBS
without 115/60/1 HCD1650NBS
Follett Vision™
undercounter
ice & beverage
dispenser
RIDE
with 115/60/1 HCD1650RVS
without 115/60/1 HCD1650NVS
Cornelius PR150
undercounter ice &
beverage dispenser
2
RIDE
with 115/60/1 HCD1650RPS
without 115/60/1 HCD1650NPS
countertop ice &
beverage dispenser
(by others)
top mount
3
with 115/60/1 HCD1650RHT
without 115/60/1 HCD1650NHT
RIDE
with 115/60/1 HCD1650RHS
without 115/60/1 HCD1650NHS
drop-in dispenser
(byothers) RIDE
with 115/60/1 HCD1650RJS
without 115/60/1 HCD1650NJS
Ice Manager diverter
valve system RIDE
with 115/60/1 HCD1650RMS
without 115/60/1 HCD1650NMS
All models ENERGY STAR®certified
1Ordered separately
2Not compatible with Micro Chewblet ice
3Requires Harmony™top kit (see page 5 for part number)
NOTE: For Micro Chewblet ice, replace second character (C) with an M
e.g. HMD1650ABT
For three phase remote condensing unit, replace third character (D) with F
e.g. HCF1010RBT
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
Job
Item
Features
Horizon Chewblet ice machine with up to 1580lb
(717 kg) dailyproduction of customer preferred Chewblet ice
- automatically transport ice through a tube with RIDE®
technology from up to 75' (22.8 m) away
- chewable, compressed nugget ice is preferred over cubes1
- Chewblet ice dispenses reliably from ice and
beveragedispensers
- available with approximately 1.00" (2.54 cm) long
standard Chewblet ice or optional 3/8" (0.95 cm) long
MicroChewblet™ice
- environmentally responsible R404a refrigerant with zero
ozonedepletion potential
- water and energy ecient
- quiet production without noisy harvest cycles
Durable, attractive ice machine
- regular bearing inspection or replacement is not required
- easy-to-read LED operating status and diagnostic display
- smooth contours for aesthetically appealing appearance
Designed with sanitation in mind
- Agion® silver-based antimicrobial product protection of key
iceand water contact components
- aluminum-bronze evaporator has antimicrobial properties
- automatic self-flushing reduces water scale buildup
- floatless, sealed design inhibits formation of biofilms
- semi-automatic cleaning and sanitizing system
Certifications
Warranty
- 3 years parts and labor, 5 years compressor parts
¹ Independent third party studies. Contact Follett for details.
² Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.

2
Form# 7040 Remote 1650 series ice machine
Specification
W1 Width 19.30" (49.0 cm)
Fits on 22.00" wide dispensers
D1 Depth 23.77" (60.4 cm)
H1 Height 23.50" (59.7 cm)
Clearance 1.00" (2.54 cm) top, right and left
Electrical
115 V/60/1
C1 6 amps, requires dedicated 15 amp circuit,
7' (2 m) cord, NEMA 5-15 plug
C2 Ice transport tube see page 6 for details
C3 Water inlet 3/8" OD push-in water inlet
C4 Drain 3/4" MPT - vented T required
C5 Ice bin signal cord connection for Vision applications only
C6 Liquid line 3/8"
C7 Suction line 7/8"
Air temperature 50 -100 F (10 - 38 C)
Water temperature 45 - 90 F (7 - 32 C)
Potable water pressure 10 - 70 psi (69 - 483 kPa)
Ice production see ice production charts on page 8
Energy consumption
90 F (32 C) air,
70 F (21C) water
single phase – 4.8 kWh
three phase – 3.7 kWh
per 100lb(45.4 kg) ice
Water consumption 12.5 gal (47 L) of potable water per 100lb (45.4kg) of ice
(per AHRI test standards) 13.2 gal (50 L) including periodic flushing
Approximate ship weight 190 lb (86 kg)
NOTE: For indoor use only
Dimensional drawing
Accessories
Harmony conversion top kit for ice and beverage
dispensers (listed on page 5)
Water filter kit (item# 00978957 – see form# 9905
fordetails)
___ ea. extra primary water filter cartridge
___ ea. extra pre-filter cartridge
Carbonless water filter kit (item# 01050442 – see form#
9905 fordetails)
Wall mount bracket (item# 00997098)
Ice machine stand, height-adjustable (item# 00128561)
Longer ice transport tube, specify length: ___ ft/m in
5'/1.5 m increments (10'/3 m is standard)
(item# 00174896)
35' (10.7 m) refrigeration lines (item# 00977785 –
not pre-charged) for 1650R
Timer to control one or two Horizon ice machines
(see accessory form# 3311)
Nu-Calgon® IMS-III sanitizer, 16 oz bottle
(item# 00979674)
SafeCLEAN™ environmentally responsible ice machine
cleaner (item#00132001)
W1
D1
H1
C3
C5
C4
C6
C7
C1
C2
Back View
2.87
(7.29 cm)
1. 81
(4.60 cm)
2.50"
(6.35 cm) 15.69"
(39.85 cm)
2.53"
(6.43 cm)
6.95"
(17. 65 cm)

3
Form# 7040
Remote 1650 series ice machine
Specification
W1 Width 36.25" (92.0 cm) – all models
D1 Depth 25.50" (64.8 cm) – all models
H1 Height 26.10" (66.3 cm) – all models
Electrical single phase 208-230/60/1
Electrical three phase 208-230/60/3
Minimum circuit ampacity single phase 29.90 A
three phase 21.24 A
Minimum overcurrent protection single phase 50 A
three phase 35 A
Electrical
208-230 V/60/3 - three phase
35 amps, requires dedicated
amp circuit, internal connection
Cooling unit operating limits
(air temperature)
min -20 F (-29 C)
max 120 F (49 C)
Maximum refrigerant line run length 100' (30.5 m)
Maximum line rise above evaporator 35' (10.7 m)
Evaporator mounting above condenser 15' (4.6 m)
Maximum refrigeration line drop 15' (4.6 m)
BTU/hr (Kcal/hr) at
0 F (-18 C) evaporator, 90 F (32C) ambient air, 1650N units only)
13,000 (3,276)
Rack systems * EPR valve - set to 0 F (-18 C)
Approximate ship weight 340 lb (154 kg)
NOTE:
1. 1650 model condensing units have a liquid suction line heat exchanger. The entire liquid line should be insulated separately from
the suction line.
2. Outdoor installation of low side is not recommended and will void warranty.
* EPR valve to be supplied by installer.
W1
D1
H1
Dimensional drawing

4
Form# 7040 Remote 1650 series ice machine
1 – Locating the ice machine
Horizon self-contained Chewblet ice machines allow top-mounting or mounting in a base cabinet, on a wall or on a floor stand up to
75' (22.8 m) from the dispenser or ice bin with RIDE technology. In-cabinet mounting (RIDE applications) require special attention to
service access, unit ventilation and ice tube runs (see pages 5-6).
Top mounting – ice and beverage dispensers (by
others)
RIDE model – Follett low-profile
Vision and Cornelius PR150 ice and beverage
dispensers
Top mount on
Follett ice storage bins
Important specifier notes: Important specifier notes: Important specifier notes:
1. Dispenser must be compatible with
nugget ice. See page 5 for compatible ice
and beverage dispenser models and top
kitnumbers.
2. Verify ceiling or soffit height to ensure
sufficient top clearance.
1. See page 5-6 for critical
clearancerequirements.
2. Ice transport tube ships with Vision ice and
beverage dispenser (Vision applications only).
3. Ice transport tube ships with Horizon series
ice machine for Cornelius dispensers.
1. See form# B300 for bin sizing.
2. Verify ceiling or soffit height to ensure
topclearance.
3. Locate floor sink or grate and drains in front
of storage bin.
4. Do not position bin drain lines to block
Ice•DevIce™bin cart.
RIDE model – ice and beverage dispensers (by
others)
RIDE model – drop-in beverage
dispensers (by others)
RIDE model –
Follett ice storage bins
Important specifier notes: Important specifier notes: Important specifier notes:
1. Dispenser must be compatible with nugget
ice. Compatible dispensers include Cornelius
DB/ED/DF150/175, Lancer 4500-22N and
FS-16N, Servend MD150/175/200/250,
SV150/175/200/250 and Follett Symphony
Plus™110CM, as well as dispensers listed on
page5.
2. Top kit MSF30SC required with Coca-Cola
Freestyle 7000. Top adapter 46412 and ice
kit 46430 must also be ordered from Coca-
Cola. Consult with Coca-Cola and Follett to
qualify application prior to ordering.
3. See page 5-6 for critical
clearancerequirements.
4. RIDE application is approved only for Pepsi
Spire 3.0 and 5.0 designed for top mount
ice machines and requires MSP24SC for 3.0
and MSP30SC for 5.0, ordered separately. For
manual fill versions of PepsiSpire 3.0 and 5.0,
contact factory.
1. Compatible with the following dispensers:
Cornelius 1522, 1722, 2323 and Lancer 2200,
2300, 23300.
2. Requires 12.00" (30.5 cm) of access space for
installation on transport tubeside.
3. See page 5-6 for critical
clearancerequirements.
1. See form# B300 for bin sizing.
2. Locate floor sink or grate and drains in front
of storage bin.
3. Do not position bin drain lines to block
Ice•DevIce bin cart.

5
Form# 7040
Remote 1650 series ice machine
1 – Locating the ice machine (continued)
Top mounting – compatible ice and beverage dispensers 1
Manufacturer Model Number Width in (cm) Depth 2 in (cm) Height 3 in (cm)
Harmony top kit – specify
"F" for front facing, or"B" for
backward facing units
Coca-Cola
dispensers
Freestyle 7000 30.10 (76.5) 33.11 (79.0) 47.00 (119.4) HTF30RC-7 4, 5
Freestyle 9000 25.50 (64.8) 35.50 (90.2) 73.75 (187.3) HTF24RC-F 4, 6
Cornelius
dispensers
DB/ED/DF 200 series 30.00 (76.2) 30.00 (76.2) 34.38 (87.3) HTC30RC-F
DB/ED/DF 250 series 30.00 (76.2) 30.00 (76.2) 38.38 (97.5) HTC30RC-F
DB/ED/DF 300 series 44.00 (111.8) 30.00 (76.2) 34.00 (86.4) HTC44RC- (F or B)
FlavorFusion/Overload 30.00 (76.2) 30.70 (78.0) 39.38 (100.0) HTC30RC-F-FF
IDC215 30.00 (76.2) 30.70 (78.0) 39.38 (100.0) HTC30RC-F-IDC
IDC255 and Pro Fast Gate 30.00 (76.2) 30.70 (78.0) 36.38 (92.4) HTC30RC-F-IDC 7
Lancer
dispensers
4500-30N 30.00 (76.2) 30.50 (77.5) 36.50 (92.7) HTL30RC-F
FS-22N 22.00 (55.9) 30.50 (77.5) 42.13 (107.0) HTL22RC-F
FS-30N 30.00 (76.2) 30.50 (77.5) 42.13 (107.0) HTL30RC- (F or B)
FS-44N 44.00 (111.8) 30.50 (77.5) 42.13 (107.0) (2) HTL22RC-F 8
Sensation 30.00 (76.2) 31.00 (78.7) 38.25 (97.2) HTL30RC-F-STP
Touchpoint 32.50 (82.55) 33.70 (85.6) 40.00 (101.6) HTL30RC-F-STP
Pepsi
dispensers
Spire 3.0 27.00 ( 68.6) 35.00 ( 88.9) 38.12 ( 96.8) HTP24RC-F
Spire 5.0 30.50 ( 77.5) 36.00 ( 91.4) 42.75 (108.6) HTP30RC-F
Servend
dispensers
MDH-302 42.75 (108.6) 31.00 (78.7) 32.38 (82.2) HTS44RC- (F or B) 2
MDH-402 60.00 (152.4) 30.50 (77.5) 32.38 (82.2) HTS60RC- (F or B) 2, 9
1All approved dispensers can be filled with a RIDE model Horizon ice machine without a top kit except Coca-Cola Freestyle 7000 and Pepsi Spire 3.0 and 5.0, see page 4 for details.
2Requires minimum 0.50"(1.27 cm) clearance between back of dispenser and wall.
3Net height after installation of top kit (excluding height of ice machine).
4Consult with Coca-Cola and Follett to qualify application prior to ordering.
5 Top adapter 46412 and ice kit 46430 must also be ordered from Coca-Cola.
6 Adapter must also be ordered from Coca-Cola. KO IC Code: 46010 (Silver), 46011 (Red) or 46012 (Black).
7Contact factory regarding IDC Pro.
8FS-44N consists of 2 separate 22.00"(55.9 cm) dispensers. A top kit is needed for each Horizon ice machine ordered.
960- inch models: Please specify number of Horizon ice machines and location. D = 2; R = 1 on right side; L = 1 on left side
2 – Undercounter/in-cabinet mounting
Cabinet details
Important specifier notes
Cabinet base
must be at & free of obstructions
(no lip or utilities to block removal)
slides
out
Cabinet door
opening
21.00"W x 24.50"H
(53.3 cm x 62.2 cm)
minimum
Ice transport tube
minimum 1/4" per foot
(2 cm per meter)
pitch toward ice machine
secure to prevent dips
and traps from forming
see dispenser
specication
sheet for
installation
requirements
12.00" (30.5 cm) minimum
between ice machine
and dispenser
drain
water
electric
1. Cabinet door opening
must meet minimum size
requirements shown and be
free of obstructions to allow ice
machine to slide out (no lip or
utilities to block removal).
2. Cabinet base must be capable
of supporting ice machine and
allow ice machine to rest flat on
cabinet bottom.
3. No counter supports, electric or
plumbing can run in front of the
ice machine.

6
Form# 7040 Remote 1650 series ice machine
3 – Horizon ice machine mounting accessories
Optional wall mount bracket Optional machine stand Important specifier notes:
22.00"
(55.9 cm)
25.50"
(64.8 cm)
23.00"
(58.4 cm)
AC
D
B
6.88"
(17. 5 cm)
A - 15.875" (40.3 cm)
B - 19.375" (49.2 cm) C - 13.00" (33.0 cm)
D - 21.00" (53.3 cm)
1. For secure wall mounting, specify
optional wall mount bracket.
2. Wall and fasteners must support the
weight of the ice machine, bracket,
supply water and ice. Use of a backing
board may be required with hollow
wallconstruction.
3. Machine stand mounting adds 6.88"
(17.5 cm) to height of ice machine.
4. No dips in tube routing allowed.
5. Ice transport tube needs minimum 1/4"
per foot (2 cm per meter) pitch toward
ice machine and should be secured to
prevent dips and traps from forming.
4 – Horizon ice tube runs - specifier guidelines
Long tube runs for RIDE remote ice delivery equipment
1/4"
1'
maximum
2' (60.9 cm)
beverage
dispenser
wall-mounted
ice machine
ice transport tube –
1 3/16" OD,
2 1/8" OD with insulation
support
straps
transport tube slope
(toward ice machine)
(2 cm per meter)
minimum of
6" (15 cm)
turn/corner
radius
Important specifier notes:
1. 75' (22.8 m) maximum ice transport
tuberun.
2. Tubing routing bends must have a
6.00"(15.2 cm) radius or larger.
3. If not supported from underneath,
secure insulated ice transport tube
at least every2' (60.9 cm) to prevent
dipsortraps.
4. Relative humidity levels above 80%
in areas where the ice machine or ice
transport tube are located may produce
excessive condensation that will cause
water damage.
5. Contact factory for recommendations
on running tubing through a decorative
soffit orchase.

7
Form# 7040
Remote 1650 series ice machine
Remote condensing unit
Condensing unit installation specifications
Important specifier notes:
=
1. Provide front, back and side clearances
asshown.
2. The maximum refrigerant line run length is
100' (30.5 m).
1650 series – 13-15 lbs of refrigerant
depending on line, consult manual
3. The maximum line rise above the evaporator
is 35' (10.7 m). Condensing unit above
evaporator unit – 35'(10.7m) (installations
with rise over 20' (6.1 m) require additional
suction line s-trap at midpoint rise).
4. The evaporator can only be mounted
a maximum of 15' (4.6 m) above the
condensing unit.
Note: The service loop is not included
when calculating length, rise or drop in
thetubingrun.
Note: To connect evaporator/ice machine to rack systems, see page 3.
48.00"
(121.9 cm)
24.00"
(61.0 cm)
48.00"
(121.9 cm)
24.00"
(61.0 cm)
air in
exhaust

Remote 1650 series ice machine
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
Form #7040 07/17
© Follett LLC
Ice production – Horizon 1650 series, air-cooled
Inlet water
temperature
F (C)
Ambient air temperature F (C)
60 (16) 70 (21) 80 (27) 90 (32) 100 (38)
lb/kg production in 24 hr
50 F (10 C) 1669 (757) 1580 (717) 1479 (671) 1422 (646) 1366 (620)
60 F (16 C) 1596 (724) 1528 (694) 1451 (659) 1387 (630) 1310 (595)
70 F (21 C) 1523 (691) 1474 (669) 1424 (646) 1350 (613) 1254 (569)
80 F (27 C) 1440 (653) 1387 (629) 1332 (605) 1267 (575) 1191 (541)
90 F (32 C) 1356 (616) 1298 (589) 1240 (563) 1183 (537) 1127 (512)
ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency.
Agion is a registered trademark of Sciessent LLC.
Harmony, Horizon, Ice•DevIce, Ice Manager, Micro Chewblet, Symphony Plus, and Vision are trademarks of Follett LLC.
Chewblet, Follett and RIDE are registered trademarks of Follett LLC, registered in the US.
Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin.