Fontana Showers FS147SBG User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
Before you begin, please read the installation instructions below. Observe
all local building and safety codes.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
Please note all products must be installed by a professional and certified
plumber otherwise warranty might be voided.
BEFORE YOU BEGIN
FONTANA SAINT DENIS LARGE BRUSHED GOLD LED
RAIN SHOWER HEAD WITH BODY JETS & HANDHELD
SHOWER INSTALLATION INSTRUCTIONS
Product code: FS147SBG
1
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Shower Head Installations Instruction
2
Shower Head Installations Instruction
Parts:
Step 3:
Step 1:
D
C
E
F F
According to drilling drawing sheet to
(B) mark the 4 drilling positions 1, then
use the Ø6mm drill to drill holes on the
wall according to the marked hole
position.
Inset the plug(D2) into the hole, hold the fix base (C) use the tapping screw (D1) through
fix base(C) holes, tighten the tapping screw (D1) tighten the top shower fixed bar(E) and
the inlet hose (F) with the fix base (C)

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
3
Fixed the top shower with the top shower fixed bar (E) , then connect with the inlet hose
(F) .
The installation is completed.
Note: The LED lights are powered by water flow, and will be activated once the water is
turned on.
E
F
Step 5:
Step 6:

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Hand Shower Installations Instruction
0.19” (4.8mm) Max
1
2
1
1. SUPPLY ELBOW INSTALLATION
Apply plumber tape to threaded ends of 1/2" (13 mm)
iron pipe nipple (not supplied) and thread into
shower riser elbow so that nipple extends past the
finished wall no more than 0.19" (4.8 mm) and no less
than 1/16" (1.6 mm). Place the supplied installation
gasket (1) behind the elbow (2). Screw the supply
elbow onto the nipple making sure that the supply
elbow outlet is in a downward facing position.
Minimum diameter for hole is 1" (25 mm) with a
maximum of 1 1/2" (38 mm).
CAUTION: To avoid damage to the supply elbow or
hose finish during installation, wrap with a cloth or
tape and use only a smooth-jawed wrench.
DO NOT OVERTIGHTEN CONNECTIONS.
3. WALL BAR INSTALLATION
Note: Hole size will be determined by your use of just the screw or
anchor and screw for installation. Drill hole for mounting of bottom
post. Start with a smaller drill bit size, 1/8" is recommended, and drill
hole. If you hit a wall stud, go to next step. If you do not hit a wall stud,
change to a drill bit size suitable for the anchors, 1/4" is recommended,
and re-drill hole.
Anchors are for use on drywall or tile. For fiberglass, acrylic and flat
plastic surfaces, use toggle bolts (not included).
Before drilling top mounting hole, it is recommended that you place
the assembled slide bar and post assembly (1) on its side next to the
hole locations you have marked. Make sure posts are pressed fully onto
bar. Align center of bottom post with bottom hole that was just drilled
and make sure center of top post aligns with mark for top hole. If not,
re-mark top hole location. If it aligns, drill top hole in location as
marked.
2. Mark the place for drilling the hole for the lower
post. Mark using a level, in a vertical line from the
lower hole, the placement of the upper post hole.
Distance approximately 25.7" (653 mm).
Step 1: Step 2:
Step 3:
4

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
1
2
3
4
1
6
2
3
4
5
6
7
8
9
1
2
3
4
5. Slide the slide mechanism (1) and elbow (2)
onto the wall bar (3). Slide wall bar over bracket
tabs (4) and secure the wall bar unit with screws
(5) provided. Install caps (6) into ends of wallbar.
Lower elbow (7) & screw (8) was pre-installed
prior to shipping, tighten screw (9) if you find it
is sliding inside bar.
6. INSTALLATION OF THE SHOWER SET
Connect the shower hose to the wall outlet (1)
and the hand held piece (2), ensuring that the
internal gaskets (3) are present in the shower
hose nuts. Normal 1/2” rubber gaskets can be
used.
Place the conical nut of the hose (4) that is
connected to the hand held piece, in the slide
bar holder (5) and turn it to desired position.
To slide the mechanism up or down, push in on
the button (6) of the mechanism and slide it on
the bar.
4. Insert anchors (1) into drilled holes. Slide
covers (2) over brackets (3), and insert screws (4)
into bracket/cover assembly. Secure assembly
to wall with screws.
Step 4:
Step 5: Step 6: Completed
5

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
6
Pressure Balancing Loop:
. If installing bodysprays in a bank of 3 or
fewer, a pressure balancing loop is not
necessary.
. If installing bodysprays in a bank of 4 or
greater, a pressure balancing loop must be
used to keep the pressure even between
the bodysprays.
Body Jets Spray Installations Instruction
Step 2: Apply teflon tape to threaded tail pipe
of the body spray
G2
Step 3: Press the escutcheon against the
finished wall
Step 4: Screw the Body spray tightly into the
female of water Supply
Step 1: Attach the escutcheon to the body
spray.

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
8
Mixer Installations Instructions
Rough-in Body
Anchor
Positioning
Bar
Tapping Screw 1
Tapping Screw 2
Plate
Cover
Button
Screw 1
Diverter
Handle
Temp.
Handle
On/Off
Handle
Hex Wrench
Hot Water
Function 1
Function 2
Function 3
Cold Water
Function 1 Function 3
Function 2
Hot Water
Cold Water
Step 2
Step 1
Step 3 ( Connection)

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
7
FontanaShowers
©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Acid
Care & Cleaning
General Information
1. The product can be cleaned with warm water, a mild soap and a clean soft cloth.
2. Clean progressively and gently.
3. It is not required to use any abrasive cleaning pads, wire wool or cloths to clean the
product.
4. Avoid a vigorous cleaning action, as this could contribute to denaturing and dulling
5. Abrasive or strong cleaning products containing ammonia, bleaches, alcohol, dyes,
acids (hydrochloric, formic, phosphorus, chlorine or acetic) will be not be affected.
All products manufactured and supplied by Fontana are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected
6. If using a spray cleaner, apply the cleaning agent onto a soft cloth, never directly
spray onto the product as the cleaner may enter gaps and openings and cause
damage. Do not allow the cleaner to remain on the product for a period of time. After
cleaning, rinse thoroughly with clean water.