Fontana Showers FS10012DF User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
Please read installation instructions below. All plumbing should be
installed in accordance with applicable building codes and regulations.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
All products must be installed by a professional and certified plumber
otherwise warranty may be voided.
PRIOR TO INSTALLATION
DUAL FUNCTION AUTOMATIC DECK MOUNT CHROME
SENSOR WATER FAUCET AND SOAP DISPENSER
INSTALLATION INSTRUCTIONS
Product code: FS10012DF
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
1

Max counter top thickness without
deck plate:
1.38”/35mm
Pre-drilled hole size requirements:
Min: 1.26”/32mm - Max: 1.38”/35mm
Faucet Deck Mount Installation
Washer
Rubber Washer
Nut and locking bolts
Threaded Tube
Faucet Body
O ring
Hole Size Chart
Washer
Rubber
Washer
Nut and
locking bolts
Water
flexible pipe
Sensor Cable
O ring
Deck Mount Type 1
Water Pipe
Deck Mount Type 2
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
2

Overview
or
Soap Bottle
Faucet Body
or
S
e
n
s
o
r
C
a
b
l
e
S
o
a
p
T
u
b
e
S
e
n
s
o
r
C
a
b
l
e
or
Soap Bottle
Faucet Body
S
e
n
s
o
r
C
a
b
l
e
S
o
a
p
T
u
b
e
S
e
n
s
o
r
C
a
b
l
e
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
3

Outlet
Inlet
This way up
G1/2
4.7 inch
5 inch
G1/2
1. Remove Control Box Cover
Remove all four screws in each corner of the control
box and remove the cover.
2. Remove Battery Box & Insert Batteries
Remove the battery case from the control box and
remove the screw from the center of the battery
case. Insert 4 AA batteries (batteries not included)
into the battery box ensuring they are inserted the
correct way.
3. Reinstall Battery Box & Control Box Cover
Re-install the battery box cover, matching the
alignment arrows together. Set the battery box back
into the control box, and re-assemble the control
box cover using the previously removed screws
ensuring they are all fully tightened.
Cover
Battery case
Battery Connector
Cover screws
Battery compartment
4a. Placement and Mounting Installation
Choose a location under the sink basin to mount the
control box, such that the sensor cable, flexible hose,
and incoming water supply all connect to the
control box. Under the sink basin, drill a hole
minimum 3/4” to fit the sensor cable and flexible
hose from the spout. Feed the sensor cable and
flexible hose through the hole.
Control Box Installation Instructions
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
4

4b. Mount the control box on the wall. Drill two 1/8"
(3mm) holes as shown, and push drywall anchors
into each hole. Secure the control box to the wall
with the drywall screws.
5. Connect The Sensor Cable
Plug the sensor cable from the faucet into the
control box to activate the infrared sensor.
6. Water Pipe Connections
Connect the incoming water supply line to the
control box, at the connection marked Inlet. Thread
on the swivel nut to the hose by hand. Tighten with
a wrench.
Connect the faucet hose to the control box, at the
connection marked Outlet.
Water Supply
Outlet Water Supply
Inlet
Please wait approximately 60 seconds after
connecting the sensor cable for sensor calibration to
complete and to begin using the faucet.
or
Temp. Control Thermostatic Mixer
Many automatic faucets do not have hot & cold
handles to adjust the water temperature coming
out of the spout, and normally installed to a single
water supply only. This valve is used for automatic
faucet to mix hot and cold water and to control
water temperature. Normally it would be mounted
under the sink with required temperature set.
Working Pressure: 0.05MPa-0.5MPa
Cold Water Temp: 0°C
Hot Water Temp: 85°C
Outlet Flow Rate: 20m3/h
Cold Water in
NPS male G1/2
Mixer Water out
NPS female G1/2
Hot Water in
NPS male G1/2
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
5

Sensor Range
This sensor faucet can automatically adjust the
inductive range within 10 seconds of electrification.
Do not use inductor during this period so that the
inductor can automatically adjust to a suitable
inductive range.
Set Water Flow Time-Out
The sensor faucet will shut off the water when
washing time exceeds 1.5 minutes. If follow-up
washing is needed, re-induce after removing hands
for 2 seconds.
Notes
1. Please use the AA type alkaline battery (1.5v for
each).
2. Place batteries into each indicated spot. Utilizing
new batteries of the same brand is best. If mixed, it
could shorten the battery life to 1-2 months.
3. After installation of the battery, the solenoid valve
will do its self-testing.
4. Wait ten seconds for power to be applied and
allow the sensor faucet to self-adjust sensor
distance. Do not use your faucet during this time.
5. If the sensor distance is too short, please move the
barrier from the faucet for 5-6 mins and allow the
sensor faucet to adjust to normal.
6. If the sensor distance is too far, and water flows
continuously, the sensor faucet will self-adjust the
distance after 5 mins.
Incorrect Placement
Keep sensor range adjustment
within 4 inches away from center
of spout. This can only be done
with optional remote control.
Installing electronic soap dispenser
& faucet with intersecting centerline
might lead to accidental activation
of either or both.
Faucet FaucetSoap
Dispenser
Soap
Dispenser
Correct Placement
Keep sensor ranges
factory preset.
Keep soap spout & faucet
centerline parallel.
Faucet Faucet
Soap
Dispenser
Soap
Dispenser
General Information
Battery Override
In the event of a power failure, the sensor faucet will
automatically switch to battery-operated mode to
ensure the faucet continues to function. The sensor
faucet can also operate on the battery alone if no
main power source is available.
Hygienic
The proximity sensor faucet removes the need to
touch the faucet body, reducing the spread of
germs and the chance of cross-contamination.
Soap Commissioning Sequence
Before using the soap dispenser for the first time,
the following sequence must be carried out.
- Fill the bottle full of soap.
- Locate the dispense button on the side of the
pump. Press and hold the button until soap is
dispensed from the spout. This will ensure the
dispenser tube and cable are full of soap.
Soap Dispenser Operation
Place your hand under the spout within the sensing
range.
Once the your hand is detected, a small amount of
soap will be dispensed from the spout into your
hand.
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Our sensor spouts have a non-touch control which
uses infrared sensing technology to detect human
presence. Once detected, the spout instantly
dispenses water and automatically stops once the
user moves their hands away to eliminate
unnecessary water wastage, whilst creating a more
hygienic washroom solution.
All products manufactured and supplied by Fontana
are safe and comply to legislative requirements.
Providing they are installed correctly and receive
regular maintenance in accordance with these
instructions your user experience will not be
affected.
6

Installation of Soap Bottle
Insert the locking
plate into bracket
Insert the pump
onto the bracket
Install the bracket
on the wall
Soap Refill Process
Affix the bottle with
full soap onto the pump,
and do not over tighten.
Add soap into
the empty bottle.
SO AP
Unscrew the
empty bottle.
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
7

Battery Box
Deck Mounted Faucet Overview
or
or
－
＋
Screws
Batteries
Battery
case cover
Battery
case
＋
－
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
8

PUSH!
Caution!
PUSH!
When the soap bottle is
filled with soap, press the button
till soap dispenses out of nozzle.
Do not use the sensor when the button is pressed,
because they cannot be used at the same time,
as it might lead to the damage to the machine.
Usage of Button
Place hands immediately
under soap spout.
Predetermined amount
of soap will dispense
If more soap is needed,
remove hands & repeat.
Usage
1. Remove cover of battery case.
2. Install four (4) D size alkaline batteries.
Note: Make sure the batteries are installed in correct orientation (polarity).
3. Replace battery case cover.
4. Tighten screws.
- The standard life cycle time is 2 years, based on average use 2000 times/month.
Anode Cathode
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
9
5
9