FoodSaver V1090 User manual

Tips for Successful Vacuum Packaging
For more usage tips and safety information, please refer to the FoodSaver Reference Guide or visit our website at www.foodsaver.com.
Sealing a Bag
Make sure you’ve placed the bag in the proper
place.When making a bag from a roll, make sure
end of cut piece is on Sealing Strip (H), not over
rubber gasket (J) or in Vacuum Channel (G).
Prevent moisture or liquid from being pulled into
the Vacuum Channel or trapped in the seal. Either
pre-freeze moist foods such as raw meat for 1-2 hours
before vacuum packaging, or place a folded paper
towel between food and end of bag to absorb excess
liquids. Just be sure to leave at least 3 inches between
paper towel and end of bag so that bag seals proper-
ly with paper towel inside.
Make sure the Seal Control Switch (E) is set to the
proper setting.
Make sure you give appliance time to cool down.
Wait at least 20 seconds between seals. Under very
heavy usage, appliance will shut off automatically to
prevent overheating. If it does, wait 20 minutes to
allow appliance to cool off.
Removing Air from a Bag
Make sure you’ve placed the bag in the proper
place. When vacuuming and sealing a bag, make
sure open end of bag is inside Vacuum Channel (G).
Check for wrinkles in the bag along the Sealing
Strip. Wrinkles in seal may cause leakage and allow
air to come back into bag. Check for wrinkles in bag
along Sealing Strip (H) before closing lid and vacu-
um packaging. If you find wrinkles after sealing bag,
simply cut bag open and vacuum package again.
If motor runs for more than 30 seconds without
stopping, you may need to adjust bag and try again.
If you are making the initial seal on a piece of bag
material with two open ends, make sure bag is placed
on Sealing Strip, not on rubber gasket (J). If you are
vacuum packaging with a bag, make sure open end
is placed down inside Vacuum Channel and make
sure Accessory Hose (F) is not attached. If you are
vacuum packaging with an accessory, check Accessory
Hose in appliance lid and in accessory to ensure a
tight fit.
Tips

General Tips
Tips for Successful Vacuum Packaging
(continued)
1. Vacuum packaging is NOT a substitute for the
heat process of canning. Perishables still need to
be refrigerated or frozen.
2. For best results, use FoodSaver Bags, Canisters
and Accessories.
3. During the vacuum packaging process, small
amounts of liquids, crumbs or food particles can
be inadvertently pulled into Vacuum Channel,
clogging the pump and damaging your appliance.
To prevent this, follow these tips:
a. For moist and juicy foods such as raw meats:
Freeze first and avoid overfilling bags. You can
also place a folded paper towel inside top of bag,
but below seal area, before vacuum packaging.
b. For soups, sauces and liquids: Freeze first and
avoid overfilling bags. Or, use a canister in
refrigerator.
c. For powdery or fine-grained foods: Avoid
overfilling bags or use a canister. You can also
place a coffee filter or paper towel inside
before vacuum packaging.
d. If your appliance features a Drip Tray, empty it
after each use.
4. To avoid overfilling, always leave at least 3 inches
of bag material between bag contents and top of
bag. Then leave at least one additional inch of bag
material for each time you plan to reuse bag.
5. Do not create your own side seams for a
FoodSaver Bag. These bags are manufactured
with a special side seam, which is sealed all the
way to the outer edge.
6. To prevent wrinkles in seal when vacuum
packaging bulky items, gently stretch bag flat
along Sealing Strip before you close lid.
7. If you are unsure your bag was sealed properly,
simply reseal bag about 1⁄4inch above first seal.
8. When you are vacuum packaging items with sharp
edges (dry spaghetti, silverware, etc.), protect
bag from punctures by wrapping item in soft
cushioning material, such as a paper towel. You
may want to use a canister or Mason jar instead
of a bag.
9. When using accessories, remember to leave one
inch of space at top of canister or container.
10.Pre-freeze fruits and blanch vegetables before
vacuum packaging for best results. See pages 2-3
of FoodSaver Reference Guide for more information.
Tips
Copyright © 2005 Tilia, Inc. All rights reserved. This material may not be reproduced or redistributed in any fashion without the express written consent of Tilia, Inc.
FoodSaver, GameSaver and the Freshness Shield logo are trademarks or registered trademarks of Tilia Int’l, Inc. in the United States and other countries. All other
trademarks are property of their respective owners. Tilia, Inc. and Tilia Int’l, Inc. are Jarden companies.This product is protected by one or more of the following Patents:
U.S. 4,660,355; 4,941,310; 5,655,357; 6,058,998; 6,256,968; Canada 1,315,746; and their equivalent international patents.
Item # T180-00249-001 (07/05)

QuickStart
V1085/1090
Shown V1085; V1090 operates in the same manner.
For important safety information and helpful tips, please refer to the FoodSaver Reference Guide
included in your kit. Questions? Visit us at www.foodsaver.com or call 1-800-777-5452 (U.S.) or
1-877-804-5383 (Canada). Get tips on vacuum packaging and order FoodSaver accessories.
Accessory Port
Seal Control Switch
(2-Position)
Accessory Hose
F
E
D
Indicator Light
Open/Cancel Button
Instant Seal Button
C
B
A
Vacuum Channel
Sealing Strip
H
GAntibacterial Drip Tray
Rubber Gasket
J
I
Features of Your FoodSaver Appliance
Features

Bags &Rolls
1. Place item(s) in bag, allowing at least 3 inches of
space between bag contents and top of bag.
2. Open appliance lid and place open end of bag
down into Vacuum Channel (G).
3. Close lid.
4. Turn Seal Control Switch (E) to:
for vacuum and seal.
to vacuum and extended seal (for moist or
juicy foods such as raw meat).
5. To begin vacuum process, press down firmly on lid
with both hands until motor starts, wait 3-5 seconds,
then release. Motor will continue to run.
6. When motor and Indicator Light (A) turn off, press
Open/Cancel Button (B) to open lid and remove
bag. Refrigerate or freeze if needed. (See FoodSaver
Reference Guide for food safety tips.)
Note: Let appliance cool down for 20 seconds
after each use.
2
1
1. Cut enough bag material from roll to hold item
to be vacuum packaged, plus 3 inches. Be sure to
cut straight.
2. Open appliance lid and place one end of bag
material across Sealing Strip (H), not over
rubber gasket (J).
3. Close lid.
4. Turn Seal Control Switch (E) to .
5. Press down firmly on lid with both hands until
motor starts, wait 3-5 seconds, then release.
Motor will continue to run.
6. When motor and Indicator Light (A) turn off,
press Open/Cancel Button (B) to open lid and
remove bag.
Now you are ready to vacuum package with your
new bag (see below).
1
How to Make a Bag from a FoodSaver Roll
How to Vacuum Package with FoodSaver Bags
Getting Started
Registering your appliance is quick and easy at www.foodsaver.com.
Place Bag on Sealing Strip Set Seal Control Switch Press and Release Lid
Place Bag in Vacuum Channel Set Seal Control Switch Press and Release Lid

Bags &Rolls
Accessories
FoodSaver Accessory Guidelines
FoodSaver Accessories
Accessories include FoodSaver Vacuum Packaging Canisters, Universal Lids, Jar Sealers and Bottle Stoppers.
1. Always leave at least one inch of space between
contents and rim.
2. Wipe rim of canister, container or bottle to ensure
it is clean and dry.
3. Place lid on canister or container, or place stopper
in bottle.
4. For accessories with a large knob on lid, turn knob
to Vacuum. Vacuum package using instructions
below. When vacuum process is complete, turn
knob to Closed before removing Accessory Hose.
5. For accessories without a large knob on lid,
vacuum package using instructions below.
How to Open FoodSaver Accessories after Vacuum Packaging
FoodSaver Vacuum Packaging Canisters
(without large knob on lid)
To release vacuum and open, push gray rubber
button on lid.
FoodSaver Bulk Canisters and Quick Marinators
(with large knob on lid) and Universal Lids
To release vacuum and open, turn knob on lid
to Open.
FoodSaver Jar Sealer with Mason Jars
For use with Ball®and Kerr®brand Mason jars.
IMPORTANT: Do NOT use screw bands when
vacuum packaging jars. To open, wedge spoon
between Mason jar lid and highest part of threaded
rim. Twist spoon gently to release vacuum.
FoodSaver Bottle Stoppers
To release vacuum and open, simply twist and pull
up on Bottle Stopper.
How to Vacuum Package with FoodSaver Accessories
1. Prepare container according to FoodSaver
Accessory Guidelines above.
2. Insert one end of Accessory Hose (F) into
Accessory Port (D) on appliance. Insert other
end into port on accessory. Twist gray tab while
inserting to ensure a tight fit.
3. Turn Seal Control Switch (E) to .
4. To begin vacuum process, press down firmly on lid
until motor starts, wait 3-5 seconds, then release.
Motor will continue to run.
5. When motor turns off, vacuum process is complete.
6. Gently twist and remove Accessory Hose from
accessory and appliance.
7. To test vacuum, simply tug on accessory lid. It should
not move.
Note: For important tips on using accessories
with different foods, please refer to the FoodSaver
Reference Guide.
1
Insert Accessory Hose Set Seal Control Switch Press and Release Lid

And More
The Instant Seal Button (C) stops the vacuum process
early and seals the bag, preventing fragile foods such
as cookies from being crushed.
1. Vacuum package as described in previous sections.
2. To stop process before all air is removed, press and
release Instant Seal Button. Vacuum process will
stop within a few seconds and bag will be sealed.
3. When light and motor turn off, open lid and
remove bag.
If fragile foods start to crush, you can also stop
the vacuum process without sealing the bag. Press
Open/Cancel Button (B) and motor will stop.
The Antibacterial Drip Tray (I) is made with an
FDA-approved antibacterial ingredient that helps
inhibit the growth of bacteria. The Drip Tray fits
inside the Vacuum Channel (G) and is removable,
making cleanup easy when small amounts of liquids
are inadvertently pulled into Vacuum Channel during
vacuum process. (See FoodSaver Reference Guide for
tips on preventing this.)
Place Drip Tray into Vacuum Channel. Two bag
guides in Drip Tray help correctly position FoodSaver
Bags when vacuum packaging. Slip open end of bag
into guides before closing lid and vacuum packaging.
After each use, empty Drip Tray and wash in warm
soapy water or place on top rack of dishwasher.
Appliance can be used without Drip Tray.
Additional Features
Instant Seal Button
Open/Cancel Button
Antibacterial Drip Tray
Accessories