Forever Redwood THE VERSAILLES ARBOR User manual

ASSEMBLY INSTRUCTIONS FOR THE
THE VERSAILLES ARBOR
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
THE VERSAILLES ARBOR
www.ForeverRedwood.com
CONTENT OF BOXES
No.
1
2
3
4
5
6
Drawing
Description
Posts
Lattice Panels
Arches
Slats
Boots
Anchor Base
Qty.
4
2
2
8
4
4
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 2
THE VERSAILLES ARBOR
www.ForeverRedwood.com
CONTENT OF BOXES
No.
A
B
C
D
E
F
Drawing
Description
-½´´ X 3 ´´ Anchor Bolts
(To attach the anchor bases to the ground).
5/16´´ X 3´´ Lag Bolts
(To attach the anchor bases to the posts).
3´´ Deck Screws
(To attach the arched rafters to the support. /
To attach the slats to the arched rafters. / To
attach the boots to the posts).
3/8´´ X 6 ´´ Bolts
(To attach the single supports to the posts. /
To attach the main knee braces to the
support).
Washers
3/8´´ Nuts
Note: Dimensions of your hardware will vary depending on size.

P| 3
THE VERSAILLES ARBOR
www.ForeverRedwood.com
No.
.
1
2
3
4
5
6
DESCRIPTION
Posts
Lattice Panels
Arches
Slats
Boots
Anchor Base
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 4
THE VERSAILLES ARBOR
www.ForeverRedwood.com
NOTE: In order to know where the post needs to be placed, check the numbers on them. If the post is not marked, then place the
single Supports on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet, only
place them on the ground to begin with”).
Step 1: Install the anchor base (6) with ½´´ X 3 ½´´ anchor bolts (A) or lag bolts. Please see the “How to anchor your pergola
document” for all details. Set your post (1) in the saddle of the anchor bases. Drill a ø ¼´´ hole in the post prior to anchoring to
facilitate the ratcheting of the hardware. After that, use a 5/16´´ X 3´´ lag bolts (B) to attach each post to its respective anchor
base.
Step 2: Attach the lattice panels (2) to the posts (1) with 3´´ deck screws (C). Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
1
1
2
2
3´´ Deck Screws
1
6
5/16´´ X 3´´ Lag Bolts
1

P| 5
THE VERSAILLES ARBOR
www.ForeverRedwood.com
Step 3: Place the arches (3), into the post notches as shown and attach to the posts with 3/8´´ X 6´´ bolts (D). Each part has a
series of numbers that indicate where to attach the part with the corresponding number.
Step 4: Attach the slats (4) to the arches with 3´´ deck screws (C). Each part has a series of numbers that indicate where to attach
the part with the corresponding number.
3
3
4
3/8´´ X 6´´ Bolts
3´´ Deck Screws

P| 6
THE VERSAILLES ARBOR
www.ForeverRedwood.com
Step 5: Finally, attach the boots (5) to the posts with 8´´ x 3´´ deck screws (C). Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
8
8
8
8
3´´ Deck Screws

P| 7
THE VERSAILLES ARBOR
www.ForeverRedwood.com
This completes the Arbor assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question, don't
hesitate to call us (866 332 2403) or email us. We are here to support you.