Forever Redwood ENTRYWAY ARBOR User manual

ASSEMBLY INSTRUCTIONS FOR THE
ENTRYWAY ARBOR
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
ENTRYWAY ARBOR
www.ForeverRedwood.com
CONTENT OF BOXES
No.
1
2
3
4
5
6
7
Drawing
Description
Posts
Supports
Knee Braces
Trellis Wall Panels
Slats
Boots
If Ordered
Anchor Bases
If Ordered
Qty.
4
2
4
2
Will
Vary.
4
4
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 2
ENTRYWAY ARBOR
www.ForeverRedwood.com
HARDWARE LIST
No.
A
B
C
D
E
F
Drawing
Description
½´´ X 4´´ Anchor Bolts
(To attach the anchor bases to the ground).
5/16´´ X 3´´ Lag Bolts
(To attach the anchor bases to the post).
5/16´´ X 3´´ Bolts
(Attach the supports to the posts. / To
attach the knee braces to the supports and
to the posts).
5/16´´ X 5´´ Bolts
(To attach the knee braces to the posts).
5/16´´ X 4 ½ ´´ Bolts
(To attach trellis wall panels to posts).
8´´ X 3´´ Deck screws
(To attach Slats to the supports. / To attach
the boots to the posts).
Note: Dimensions of your hardware will vary depending on size.

P| 3
ENTRYWAY ARBOR
www.ForeverRedwood.com
No
1
2
3
4
5
6
7
DESCRIPTION
Posts
Supports
Knee Braces
Trellis Wall Panels
Slats
Boots
Anchor Bases
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 4
ENTRYWAY ARBOR
www.ForeverRedwood.com
NOTE: In order to know where the posts need to be placed, check the numbers on them. If the post is not marked, then place the
arched roof timbers on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet,
only place them on the ground to begin with”).
Step 1: Install the anchor bases (7) with ½´´ X 4´´ anchor bolts (A) or lag bolts. Please see the “How to anchor your pergola
document” for all details. Set your post (1) in the saddle of the anchor bases. Drill a ø ¼´´ hole in the post prior to anchoring to
facilitate the ratcheting of the hardware. After that, use a 5/16´´ X 3´´ lag bolts (B) to attach each post to its respective anchor
base.
Step 2: Attach the supports (2) to the posts with 5/16” x 3” bolts (C) washers & nuts. Tap the bolt all the way into the wood to
set it. Then add a washer and nut and lightly tighten. Each part has a series of numbers that indicate where to attach the part with
the corresponding number.
1
2
2
5/16´´ X 3´´ Bolts
1
1
1
7
5/16´´ X 3´´ Lag Bolts

P| 5
ENTRYWAY ARBOR
www.ForeverRedwood.com
Step 3: Attach the knee braces (3) to the supports with 5/16” x 3”bolts (C) and to the posts with 5/16” x 5” bolts (D), washers
& nuts. Each part has a series of numbers that indicate where to attach the part with the corresponding number.
Step 4: Attach the trellis wall panels (4) to the posts with 5/16” x 4 ½” bolts (E) washers & nuts. Each part has a series of numbers
that indicate where to attach the part with the corresponding number.
5/16´´ X 3´´ Bolts
5/16´´ X 5´´ Bolts
3
3
4
5/16´´ X 4½´´ Bolts
3
3
4

P| 6
ENTRYWAY ARBOR
www.ForeverRedwood.com
Step 5: Attach the Slats (5) to the supports with 3” deck Screws (F). Each part has a series of numbers that indicate where to
attach the part with the corresponding number.
Step 6: Finally, use 3” deck Screws (F) to attach the boots (6) to the posts.
2.3
5
8´´ X 3´´ Deck screws
6
6
6
6
8´´ X 3´´ Deck screws

P| 7
ENTRYWAY ARBOR
www.ForeverRedwood.com
This completes the Arbor assembly. Hope you enjoy your set for many decades. If you ever have a problem or a
question, don't hesitate to call us (866 332 2403) or email us. We are here to support you.