Forever Redwood ADIRONDACK CHAIN GLIDERS User manual

ASSEMBLY INSTRUCTIONS FOR THE
ADIRONDACK CHAIN GLIDERS
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 1
CONTENT OF BOXES
No.
1
2
3
4
5
6
7
Drawing
Description
Supports
Legs
Base Legs
Diagonal Supports
Armrests
Seat
Backrest
Qty.
2
2
2
2
2
1
1
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 2
HARDWARE LIST
No.
A
B
C
D
E
F
Drawing
Description
3/8´´ X 7´´ Bolts
(To attach the legs to the supports. / To
attach the diagonal supports to the legs and to
the supports).
5/16´´ X 5 ½´´ Bolts
(To attach the base legs to the legs).
3/8´´ X 8´´ Bolts
(To attach the base legs to the legs).
5/16´´ X 3 ½´´ Bolts
(To attach the armrests to the seat and to the
backrests).
Chains
Quick links
Note: Dimensions of your hardware will vary depending on size.

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 3
No
1
2
3
4
5
6
7
DESCRIPTION
Supports
Legs
Base Legs
Diagonal Supports
Armrests
Seat
Backrest
Note: Part numbers in the Drawing are for
reference only. These do not match to the
numbers marked on the parts sent.
1
1
2
2
3
3
4
4
5
5
6
7

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 4
Step 1: Attach the legs (2) to the supports (1), with 3/8” X 7” bolts (A). Tap the bolt all the way into the wood to set it. Then add
a washer and nut and lightly tighten. Each part has a series ofnumbers that indicate where to attach the part with the corresponding
number
Step 2: Attach the base legs (3) to the legs with 5/16” X 5 ½” bolts (B) and 3/8” X 8” Bolts (C). Tap the bolt all the way into the
wood to set it. Then add a washer and nut and lightly tighten. Each part has a series of numbers that indicate where to attach the
part with the corresponding number
3/8´´ X 7´´ Bolts
2
2
1
3/8´´ X 8´´ Bolts
5/16´´ X 5 ½´´ Bolts
3
3

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 5
Step 3: Use 3/8” X 7” bolts (A) to attach the diagonal supports (4) to the legs and to the supports. Tap the bolt all the way into
the wood to set it. Then add a washer and nut and lightly tighten. Each part has a series of numbers that indicate where to attach
the part with the corresponding number
Step 4: Attach the Armrests (5) to the Seat (6), with 5/16” x 3 ½ bolts (D), washers & nuts. Tap the bolts all the way into the
wood to set it. Then add a washer and nut and lightly tighten. Each part has a series of numbers that indicate where to attach the
part with the corresponding number.
5
5
6
5/16´´ X 3 ½´´ Bolts
3/8´´ X 7´´ Bolts
4
4

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 6
Step 5: Use 5/16” x 3 ½ bolts (D) to attach the backrest (7) to the armrests. Tap the bolts all the way into the wood to set it. Then
add a washer and nut and lightly tighten. Each part has a series of numbers that indicate where to attach the part with the
corresponding number
Step 6: Finally, with someone helping you, use quick links (F) and chains (E) to join the seat glider to the frame glider. Take a
few minutes to adjust the chain height to your preference.
7
5/16´´ X 3 ½´´ Bolts
Chains & Quick Links

ADIRONDACK CHAIN GLIDERS
www.ForeverRedwood.com P| 7
This completes the assembly of the Two Seat Adirondack Glider; I hope you enjoy your set for many decades. If you ever have a
problem or question, do not hesitate to call us (866 332 2403) or send us an email. We are here to support you.