Forever Redwood THE SILVERADO MODERN PERGOLA User manual

P| 0
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
ASSEMBLY INSTRUCTIONS FOR
THE SILVERADO MODERN PERGOLA
866.332.2403 (TOLL FREE) (707) 640.29.05 (Option 4) Direct Line for the Design
Department; 7am –7pm Pacific Time, Monday-Saturday

P| 1
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
NOTE: Assembly is best done by two people. To assemble your product, you need a Hammer, a Ratch or a wrench and if
required a Drill.
PROCESS TO INSTALL THE HARDWARE PROVIDED.
Required Tools (Are not included in your hardware packing).
To install the bolts.
Insert the carriage bolts into the holes and lightly tap with a hammer until the square neck fit in the wood piece and the bolt
head must flush with the wood piece. Finally, place the washer and the nut and carefully tighten it using a ratchet with the
necessary socket or a wrench.

P| 2
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
To install the lag bolts.
Place the washers in their lag bolts. After that, insert the lag bolts into the holes and carefully tighten it using a ratchet with
the necessary socket.
Use the washers only for the Wood Pieces.
To install the deck screws.
Insert the deck screws into the holes and carefully tighten it using a drill.

P| 3
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
CONTENT OF BOXES
Description
Drawing
No.
Posts
1
Single Supports-A
2
Single Supports-B
3
Single Supports-C
4
Supports with
In-Between Blocking-A
5
Supports with
In-Between Blocking-B
6
Supports with
In-Between Blocking-C
7
Rafter
8
In-between blocking cover
9
increase of rafter
10
Slat
11
Curtain roads
12
Ceiling fan base
13
L-plaques cover
14
Boots
15
L-plaques
16
Curtain bases
17
Anchor bases
18
High wind anchor bases
19
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on
the parts sent.

P| 4
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
HARDWARE LIST
Description
Drawing
No.
½” x 3 ½” anchor bolts
AB1
5/16” x 3” lag bolts
LB1
3/8” X 10” lag bolts
LB2
3/8” x 4” lag bolts
LB3
3/8” x 2 ½” lag bolts
LB4
3/8” x 5” lag bolts
LB5
3/8” X 7 ¼” bolts
BL1
3/8” X 8” bolts
BL2
3/8” x 10 ½” bolts
BL3
3” deck screws
DS1
2” Deck Screws
DS2
Note: Dimensions of your hardware will vary depending on size.

P| 5
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
DESCRIPTION
No.
Posts
1
Single Supports-A
2
Single Supports-B
3
Single Supports-C
4
Supports with
In-Between Blocking-A
5
Supports with
In-Between Blocking-B
6
Supports with
In-Between Blocking-C
7
Rafter
8
In-between blocking
cover
9
increase of rafter
10
Slat
11
Curtain roads
12
Ceiling fan base
13
L-plaques cover
14
Boots
15
L-plaques
16
Curtain bases
17
Anchor bases
18
High wind anchor bases
19

P| 6
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 7
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
NOTE: In order to know where the post needs to be placed, check the numbers on them. If the post is not marked, then place
the single Supports on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet,
only place them on the ground to begin with”).
Note: Before install the anchor bases make sure that the ground is level using a carpenter's level or hydro-level (water level).
Step 1: Install the high wind anchor bases (19) and Anchor Bases (18) with ½” x 3 ½” anchor bolts (AB1). Please see the
“How to anchor your pergola document” for all details. Set your post (1) in the saddle of the anchor bases. Drill a ø ¼´´ hole in
the post prior to anchoring to facilitate the ratcheting of the hardware. After that, use 5/16” x 3” Lag Bolts (LB1) to attach each
post to its respective anchor base.
Step 2: Use 3/8” X 7 ¼” bolts (BL1) and 3/8” X 8” bolts (BL2) to attach the single Supports-B (3) to the posts (1). Check the
marked on each support and place as drawings shown.
Note: Don’t completely tighten yet the bolts–you will need the install the supports with in between blocking first.
A-3
A-4
A-1
A-2
B-3
B-8
BL1
A-5
A-6
LB1
BL2
LB1

P| 8
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 3: Use 3/8” X 10” lag bolts (LB2)and 3/8” X 8” bolts (BL2) to attach the single Supports-A (2) to the posts (1). Check the
marked on each support and place as drawings shown.
Note: Don’t completely tighten yet the bolts–you will need the install the supports with in between blocking first.
Step 4: Place the supports with in between blocking-A (5) into the post notches. Return to the bolts described in the step 3 and
tighten fully. After that use 3/8” X 7 ¼” bolts (BL1) to attach the supports together. Check the marked numbers on each support
with in-between blocking and place as drawings shown.
B-9
B-10
LB2
BL1
B-11
B-12
BL2

P| 9
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 5: Use 3/8” X 7 ¼” bolts (BL1) to attach the single Supports-C (4) to the posts (1). Check the marked on each support and
place as drawings shown.
Note: Don’t completely tighten yet the bolts–you will need the install the supports with in between blocking first.
Step 6: Place the supports with in between blocking-B&C (6, 7) into the post notches. Return to the bolts described in the step 3
and tighten fully. After that use 3/8” X 7 ¼” bolts (BL1) to attach the supports together. Check the marked numbers on each
support with in-between blocking and place as drawings shown.
B-4
BL1
B-7
B-6
BL1
B-5

P| 10
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 7: Use 3/8” x 10” lag bolts (LB2) to attach the supports together.
Step 8: Use 3/8” x 4”lag bolts (LB3) to attach the supports together. Check the marked numbers on each support and place as
drawings shown.
LB2
LB3
LB3
B-1
B-2
LB2

P| 11
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 9: Use 3/8” x 10” lag bolts (LB2) to attach the supports together. Check the marked numbers on each support and place as
drawings shown.
Step 10: Use 3” deck screws (DS1) to attach the in-between blocking cover (9) to the supports with in-between blocking.
9
DS1
LB2

P| 12
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 11: Use 3/8”x 2 ½” lag bolts (LB4) to attach the L-Plaques (16) and curtain bases (17) to the posts and to the supports.
|
Step 12: Use 2”Deck Screws (DS2) to attach the L-plaques cover (14) to the posts and to the supports.
|
16
14
LB4
DS2
17

P| 13
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 13: Attach the increase of rafter (10) to the supports with 3” Deck Screws (DS1) and 3/8” x 5” lag bolts (LB5). Check the
marked on each increase rafter and place as drawings shown.
Step 14: Attach the rafters (8) to the Increase of rafters (10)with 3” deck screws (DS1). Check the marked on each rafter and
place as drawings shown (C-1 at C-52).
C-1
C-52
10
DS1
DS1
LB5

P| 14
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 15: Use 3”deck screws (DS1) to attach the slats (11)to the rafters (8). Check the marked on each slat and place as drawings
shown.
Step 16: Use 3/8” x 10 ½” bolts (BL3) to attach the ceiling fan base (13)to the rafters (8). Check the marked on each ceiling fan
and place as drawings shown.
D-1
D-3
D-2
D-4
DS1
BL3
F-1

P| 15
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
Step 17: Put the curtain roads (12) in place.
Step 18: Finally, attach the boots (15) to the posts with 3” deck screws (DS1).
15
DS1
12

P| 16
THE SILVERADO MODERN PERGOLA
www.ForeverRedwood.com
This completes the Pergola assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question,
don't hesitate to call us (866 332 2403) or email us. We are here to support you.