Courtyard Creations RVS949W User manual

PAGE 1 OF 4E-3
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL
USE INTENDED FOR RESIDENTIAL USE ONLY.
RVS949W
SHADOW CREEK ALL-WEATHER WICKER
CUSHIONED DEEP SEATING SWIVEL GLIDERS - 2PK
COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until the swivel glider is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
"
"
"
"
"
2
11
1
1
1
1
4
214
13
15
16
4
3
PART
NO. MATERIAL CODE PART Q’TY
BACK ASSEMBLY
SEAT ASSEMBLY
LEFT ARM
RIGHT ARM
WASHER d6.5*D30*2.0
SUPPORT FRAME WASHER d8.5*D12*2.1
WASHER d8.5*D12.5*1.5
SEAT POST PLASTIC NUT M6*P1.0
DECORATIVE
PLASTIC COVER JAM NUT M8*1.25
BASE ASSEMBLY HEX. KEY WRENCH 4MM
BOLT M6*40 HEX. KEY WRENCH 6MM
BOLT M6*65 NUT WRENCH 10&13MM
BOLT M6*35 BACK CUSHION
BOLT M8*30 SEAT CUSHION
WASHER d8.5*D17*1.6
RVS949W-CS03-1
RVS949W-CS02-1
RVS949W-CS01-2
RVS949W-CS01-3
17FA05040301-YX
17FA05100701-YX
17FA08060601-YX
17FC08030801-YX
17FD08300501-YX
418
1217
PARTS LIST
WASHER d6.5*D13*1.0
4
17C03A0814041YX
15
BOLT M8*40
RVS949W-CS14-1
18000C23001 21916 RFS8821-CS04
17D03A040401-YX 42017 18000744004
17KAA0101----Y4 12118 RVS949W-CS12-2
17KAA0201----Y4 12289 17C40A0714001YX
17KAB1101----Y4 123210 17C40A0722001YX
61R949WX00001BA 124111 17C40A0712001YX
61R949WY00001BA 125412 17C01A0810001YX
Y
ME

FIGURE 1 FIGURE 2
FIGURE 3 FIGURE 4
Step 1:
Place the back assembly (#1) onto a non-abrasive
surface, such as a carpet. Fasten the arms (#3 and #4)
to the back assembly (#1) by using bolts (#9).
Keep the bolts loose. See Figure 1.
Step 3:
Fasten the seat assembly (#2) to the back assembly
(#1) by using bolts (#10), washers (#14) and plastic
nuts (#19). See Figure 3.
Note:
The labels marked “L” and “R” on the arms (#3 and #4)
should coincide with Figure 1 to ensure proper assembly.
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
L
R
#9 BOLT M6*40
3
1
9
9
4
#9
B
O
LT M
6
*4
0
40
#9 BOLT M6*40
#9
B
O
LT M
6*
4
0
40
Step 2:
Fasten the seat assembly (#2) to the arms (#3 and #4)
by using bolts (#9). Keep the bolts loose.
See Figure 2.
Step 4:
Turn the seat assembly to its upright position.
Fasten the support frame (#5) to the arms (#3 and #4)
by using bolts (#12) and washers (#17). See Figure 4.
PAGE 2 OF 4E-3
2
99
2
3
4
1
10
19
3
4
14
#10 BOLT M6*65
65
#12 BOLT M8*30
30
12
17
17
17
3
4
30
5

FIGURE 5 FIGURE 6
FIGURE 7 FIGURE 8
Cleaning and Maintenance
Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
The cushions may be washed on the surface only by using mild soap and water or a commercial foaming
upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
We recommend the use of furniture covers when not in use.
Inspect and tighten all of the bolts and fasteners on a regular basis to ensure the proper performance and
safety of your swivel glider.
In order to prolong the life and beauty of your swivel glider,
we recommend that it be stored in a dry and
protected
area during off season periods.
Step 5:
Fasten the seat post (#6) to the support frame (#5) by
using bolts (#13), washers (#16 and #18) and jam nuts
(#20). See Figure 5.
Step 7:
Insert the seat post (#6) into the hole in the center of
the base assembly (#8). Fasten them together by using
bolt (#11) and washer (#15). Make sure that all of the
bolts have been tightened completely. See Figure 7.
Note:
For ease with installation, we recommend that the seat
post (#6) be slightly olied or waxed before fastening it to
the base assembly (#8).
Step 6:
Place the decorative plastic cover (#7) on the chair's
base assembly (#8) as above picture A shows.
See Figure 6.
Step 8:
Turn the swivel glider to its upright position. Place the
cushions (#24 and #25) onto the swivel glider.
See Figure 8.
Caution:
To ensure one’s safety during use of this swivel glider,
make sure that all of the bolts are completely tightened.
This chair has the ability to swivel; therefore use by
young children should be adult supervised.
PAGE 3 OF 4E-3
20
20
18
18
5
16
16
13
13
6
5
6
40
#13 BOLT M8*40
A
A
7
7
8
824
25
8
7
8
7
#11 BOLT M6*35
35
11
15
6

Swivel glider is for sitting purposes only. Standing on or misuse of swivel glider may result in damage or injury.
Weight limit 250 lbs (113.5kg). Not intended for commercial use.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL OF THE PARTS, MAKING SURE THAT
YOU HAVE ALL OF THE PARTS LISTED.
IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY
PARTS ARE MISSING OR DAMAGED, CALL THE HELP LINE AT
1-877-539-7436 BEFORE RETURNING THIS ITEM TO THE STORE.
PROVIDE THE FOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THE PRODUCT.
2-PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS
LIST.
MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS
PRODUCT TO THE RETAILER.
Warranty
This product is covered by Courtyard Creations Inc.'s one–year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer’s responsibility for freight and packing charges to and from the service center.
PAGE 4 OF 4E-3