Formax FD 8500HS User manual

High Security Paper Shredder
FD 8500HS Cross-Cut / Level 6
OPERATOR MANUAL
FIRST EDITION
10/08
Safety Devices and Other Features
Formax 8000 Series Shredders are equipped with various safety features:
Automatic Reverse Rotation
(Process takes about 6 to 8 seconds)
When too much paper is inserted, the cutter stops operating
and
automatically rotates in reverse to discharge the jammed paper. An
alarm sounds. Reduce the amount of paper and restart the operation.
Door Switch
If the door is open, the shredder will not operate.
Automatic Stop
When the shredded paper fi lls the waste bin, the “FULL”
light comes
on and the cutter stops operation. Open the door, remove the waste
bin and empty paper shreds. Replace the waste bin, close the door
and continue operation.
Automatic Power Shut-Off
• If the shredder operates continuously for more than 30
minutes,
the power is automatically shut off.
• If the motor is overloaded, the “STOP” LED will fl ash until it cools
down. When the fl ashing stops the shredder is ready to be used
again.
Oil Indicator
Oil regularly for peak performance
.
NOTE:
High Security shredders require
a specialized oil that can only be ordered through Formax, part # 8000-15
.
The
“MANUAL” LED will fl ash after every four (4) hours of operation as an indicator to oil
the shredder cutting blades. The LED will continue to fl ash until oiled. NOTE: the
shedder will still operate when the LED is fl ashing but at a decreased load capacity.
To oil:
Spread shredder oil onto the cutters through the feed opening, and allow the
oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button
and hold for fi ve seconds. “MANUAL” and “REV” LED indicators on control panel will
light. The shredder will operate in reverse for one minute, then the “AUTO” LED will
light indicating the shredder is ready.
Maintenance
• Disconnect power by pulling power cord plug from wall outlet.
• To clean the exterior, wipe the surface with a soft cloth. If the surface is
very dirty,
use a neutral detergent, then wipe again with a soft cloth.
CAUTION:
• Never put water directly on the surface of the shredder.
• Never clean the case with benzene or thinner, since it will cause discoloration.
• Do not dismantle the shredder. Contact your Formax Dealer for service.
NSA Approved
Meets the requirements of NSA/CSS specifi cation for
Level 6 High-Security cross-cut shredders.

Operation
1. Open the door and fl ip the breaker switch to the “ON”
position. Close door. Press the Power Switch on the right side
of the shredder to the “ON” position (This switch should be used
to turn the power on and off).
2.
Auto Start/Auto Stop
When the “START” button is pushed, the signal lamp “AUTO”
will light. Insert paper to shred. The shredder will start and stop
automatically when using this function.
3.
Manual Operation
If paper is too small for the shredder’s sensors to detect, shred
it manually. Push the “START” button once more and the
“MANUAL” lamp will light. Insert paper to be shredded. Three
minutes after shredding, the cutter automatically stops rotating.
Safety Precautions
To avoid personal injury, and damage to the shredder, observe the following safety
precautions. Please keep these instructions for future reference.
Set-up Guidelines
1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared
with another electronic device, the total current should not exceed 30A (at 110V).
Specifi cations
Cutting Style:
Cross Cut
Shred Size:
1/32” x 3/16” (Level 6)
Sheet Capacity:
4 to 5 (
NO staples or paper clips
)
Speed:
39 feet per minute
Feed Opening:
16”
Dimensions:
24” W x 20” D x 35” H
Bin Capacity:
26 gal.
Weight:
242 lbs.
Power supply:
110-120V, 60Hz
FD 8500HS - For paper only
4.
Reverse Operation
Push the “REV” button and the signal lamp “REV” will light and cutters will operate in
reverse. If too much paper is inserted at one time in standard modes, the shredder
will automatically operate in reverse. If this occurs, remove the inserted paper and
shred in smaller amounts. NOTE: The maximum amount of paper to be shredded
differs according to paper quality, humidity and voltage. If the shredder is to be used
continuously, do not insert more than half of the maximum capacity.
5.
Full Sensor
If the waste bin is full, the “FULL” lamp will light and the cutter will stop automatically.
Open the door, empty the waste bin of paper shreds, replace the waste bin, close
door, and continue to shred.
NOTE:
In case of emergency, push the
“Power Switch” to cut off power and/or pull
the plug out of the wall outlet.
•
Keep hands, long hair, clothing, ties, jewelry
and loose items away from the feed opening
and shred outlet.
•
Do not use the shredder for anything other
than its intended purpose. Never use it to
shred cloth, plastic, cardboard or any hard
material that will cause damage to the
shredder blades.
DO NOT SHRED STAPLES OR PAPER CLIPS, THEY WILL
DAMAGE OR DESTROY THE CUTTING BLADES.
•
Do not allow children to use the machine.
•
Do not operate with a damaged power cord or plug, or when the machine
is
damaged in any manner.
•
Unplug the shredder when it is being moved, or if it is not in use for an
extended
period of time.
•
Do not disconnect the power by pulling only the cord. Hold the plug when
disconnecting.
•
Keep the shredder away from direct sunlight.
•
Do not sit on the shredder or place anything on top of it.
•
Never open the fi xed switch or cover.