FormFit HD 13B13 User manual

HD 13B13 Rev0 Dec 22, 2017 1 of 8
PARTS LIST
Hood Protector Installation Tape
Hood Protector
Large Pedestals (3)
Clip Bodies (4)
Pins (7)
# 6 x 5/8” Flat Head Screws (7)
Anti-abrasion Film Pads Large (4)
Anti-abrasion Film Pads Small (3)
Large Metal Mounting Brackets (3)
Metal “L” Brackets (4)
Alcohol Wipes (1)
Tape strip sheet (repositionable) (1)
TOOLS AND SUPPLIES REQUIRED
Long Shank Phillips Screwdriver #2
Tape Measure
Grease Pencil
Masking Tape
INSTALLATION
Make sure the vehicle is clean and completely dry before
installation.
This product uses a 3M adhesive product that requires
installation and curing temperatures of at least 20°C/ 70°F
for 24 hours to develop maximum adhesion to the surface.
Failure to install this product at the proper temperature or
allow adequate curing time before use is not covered under
warranty.
Proper installation of the adhesive pedestal system
requires the use of a #2 Phillips screwdriver, preferably
with a long shaft. The shaft of the screwdriver needs to
fit through the hole in the pedestal. Use of the correct
screw driver will facilitate a trouble free installation. Do
not attempt to use #1 or smaller Phillips screwdriver or
any type of electric screwdriver.
1. Insert a pin through the hole in the Hood Protector Installation
Tape supplied and into one of the large adhesive pedestals.
2. Install one of the #6 x 5/8 flat head screws into the pedestal.
Locate centre pedestal using installation tape.
3. Estimate the centre of the hood and using masking tape or the
repositionable tape strips supplied, tape the pedestal into
position.
Use the installation tape to confirm centre by measuring two
opposite corners of the hood and adjust pedestal until both
measurements are identical.
NOTE: The fingers incorporated on the leading edge of the
pedestal will help ensure the correct position relative to the
hood edge. When correctly positioned the fingers should
contact the leading edge of hood
Hood Protector
Installation Instructions
HD 13B13
Nissan Sentra 2013 - 15

HD 13B13 Rev0 Dec 22, 2017 2 of 8
Locate other pedestals using installation tape.
4. The positions of the pedestals are shown in the
illustration. Use the center mark on the leading
edge of the pedestals for accurate measuring.
The fingers incorporated on the leading edge of
the pedestal will help ensure the correct position
relative to the hood edge. When correctly
positioned the fingers should contact the leading
edge of the hood.
5. Place the hood deflector on the pedestals to
confirm proper positioning. Ensure the holes
in the deflector align with those in the
pedestals. If necessary, reposition the
pedestals so all attachment positions are
correct and the deflector is well centered.
6. Remove the hood deflector, and outline the
perimeter of the pedestals with masking tape or
the repositionable tape strips supplied to help
final installation.
7. Remove the pedestals and thoroughly clean the
outlined area with the alcohol wiping pad. This
will insure all wax, finger prints and oils are
removed from the hood surface in the bonding
area.

HD 13B13 Rev0 Dec 22, 2017 3 of 8
8. Remove the protective backing film from each of the
adhesive pedestals and install them on the hood surface.
Tip: Hook the fingers on the pedestal over the hood edge and
rotate the unit into position. After installation, remove the
masking tape and “wet out” the pedestal base by applying
pressure with your thumb around the surface of the
pedestals.
9. Start a #6 x 5/8 flat head screw into each pedestal a few
turns. The tip of the screw must not protrude into the hole
where the attachment pin will install later.
10. Peel and fold the small anti abrasion film pad in half over the
hood edge between the fingers on each of the pedestals.
11. Push a metal mounting bracket over the hood edge on top of
the anti abrasion pad installed previously. Ensure the
bracket is fully engaged over the hood edge and the hole in
the bracket is aligned with the hole in each of the pedestals.
12. Place the deflector on the pedestals and drop a pin through
the deflector and into the pedestal.
13. Maintain slight pressure on the pin, to ensure proper seating
of the components, while simultaneously tightening the
screw on all of the adhesive pedestals.
NOTE: Only tighten screw a few turns so that the pin is held
in but there is some movement of the deflector. This helps
with the installation of the components above the headlights.

HD 13B13 Rev0 Dec 22, 2017 4 of 8
14. Peel and fold two (2) of the large anti-abrasion film pads in
half over the hood edge aligned with the inner holes of the
deflector in the area above the headlights.
15. Place a clip body over each of the anti-abrasion film pads on
the edge of the hood.
16. Insert a pin through the protector into each of the clip
bodies.
17. Insert a #6 x 5/8’’ screw through an ‘L’- bracket and into
the clip body.
18. Make sure all the components are well seated together;
the protector is centered on the hood, and then tighten
the screws into the clip bodies.
19. Repeat steps 14- 18 for the outer holes of the deflector over
the headlights.
20. Tighten all the screws that are in the adhesive
pedestals.
CARE
Hand clean the deflector using a mild soap and water solution
or plastic cleaner only.
Avoid automatic car-wash equipment where a brush and/or soft
cloth come in contact with the hood deflector. Touch-less style
automatic car-wash equipment is less likely to harm the air
deflector.
Service
Periodically check to confirm the deflector is securely attached
to the hood.
WARNINGS
Do not pull/push on the deflector when opening/ closing the hood.

HD 13B13 Rev0 Dec 22, 2017 5 of 8
LISTE DE PIÈCES
Ruban capot protecteur installation
Déflecteur de capot
Piédestaux adhésifs (3)
Corps d'agrafe (4)
Goupilles (7)
5/8 de vis principales plates de #6 X » (7)
Tampons Film anti-abrasion grandes (4)
Tampons Film anti-abrasion Petit (3)
Supports en métal (3)
Parenthèses de L de ` (4)
Alcool essuyant des garnitures (1)
Band de ruban (repositionnable) (1)
OUTILS REQUIS
Tournevis à tête étoilée à jambe longue n° 2
Ruban à mesurer
Crayon gras
Ruban-cache
INSTALLATION
S’assurer que le véhicule est propre et complètement sec avant
l'installation.
Ce produit contient un ruban adhésif 3M. Il est nécessaire
d’effectuer l’installation à une température d’au moins 20°C/
70°F. Patienter pendant 24 heures pour permettre à l’adhésion
de bien se solidifier. Une installation inadéquate en ce qui
concerne la température ou le délai d'attente entrainera
l’annulation de la garantie.
L'installation correcte du système de piédestal adhésif exige
l'utilisation d'un tournevis à tête étoilée no2, préférablement à
jambe longue. La jambe longue doit s'ajuster dans le piédestal à
travers le trou. L'utilisation du tournevis approprié facilitera une
installation sans problème. Ne pas tenter d'utiliser le tournevis
no1 ou un plus petit tournevis à tête étoilée, ou n’importe quel
type de tournevis électrique.
1. Insérer une broche dans le trou de la bande d'installation fourni
Protège et dans l'une des grandes socles adhésifs.
2. Installez l'un des n ° 6 x 5/8 vis à tête plate sur le
piédestal.
Localisez console centrale avec du ruban installation.
3. Estimer le centre de la hotte et à l'aide du ruban adhésif ou des
bandes adhésives repositionnables fournis, l'adhésif du socle
en position.
• utiliser la bande d'installation pour confirmer centre par la
mesure de deux coins opposés de la hotte et ajuster socle
jusqu'à ce que les deux mesures sont identiques.
REMARQUE: Les doigts incorporés à la fine pointe du piédestal
aidera à assurer la bonne position par rapport au bord capot. Lorsqu'il
est correctement positionné les doigts doivent communiquer avec le
bord d'attaque du capot
Déflecteur de capot
INSTRUCTIONS POUR l'INSTALLATION
HD 13B13
Nissan Sentra 2013 - 15