Fortinet FortiBridge-2001F User manual

QuickStart Guide
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks of
their respective holders.
Regulatory Compliance
FCC Class A Part 15, UL/CB/CUL, C Tick, VCCI
26 October 2010
FortiBridge-2001F
INT3 EXT3
FortiBridge 2001F
USB
CONSOLE MODEM MGMT
INT1
INT2
INT1
INT2
EXT1
EXT2
EXT1
EXT2
HA
PWR NORMAL
BYPASS
MODE RESET
FortiGate
09-300-132991-20101117
Visit these links for more information and documentation for your Fortinet product:
Technical Documentation - http://docs.fortinet.com Fortinet Knowledge Center - http://kb.fortinet.com
Technical Support - http://support.fortinet.com Training Services - http://campus.training.fortinet.com
Conguring
AC Power 50 W, 100 - 240 VAC, 50 - 60Hz
Chassis 1U
Dimensions 44.0 cm x 30.1 cm x 4.44 cm
Network Interfaces
2 1GB LC SFP (SX) Ingress/Egress ports
2 1GB SFP (SX) Ingress/Egress ports
1 10/100/1000 Management port
1 USB connection
1 Console port
1 Modem connection
Command Line Interface
To connect to the FortiBridge unit
1. Use a RJ-45 to DB-9 cable to connect the FortiBridge management port to the man-
agement computer serial port.
2. Start a terminal emulation program (such as HyperTerminal) on the management
computer. Use these settings: Baud Rate 9600, Data bits 8, Parity None, Stop bits 1,
Flow Control None.
3. At the login: prompt, type admin and press Enter twice.
(The login prompt is preceded by the server default host name.)
To congure the FortiBridge unit using the CLI
1. Change the management IP address.
cong system manageip
set ip <intf_ip>/<netmask_ip>
end
2. Congure the primary and secondary DNS server IP addresses.
cong system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
3. Congure the default gateway.
cong system route
edit 1
set gateway <gateway_ip>
end
4. Change the administrator password.
cong system admin
edit admin
set password <password>
end
Shutting down the FortiBridge unit
When powering off the FortiBridge unit, always shut down the unit using the following pro-
cedures before disconnecting the power supply. Not following this procedure can increase
the risk of damaging the FortiBridge ash disk.
To power off the FortiBridge unit
1. Go to System > Status.
2. In the Unit Operation area, click Shut Down.
3. Once the indicates the shut down procedure has completed, disconnect the
FortiBridge unit from the power source.
Web-based Manager
Use the following procedure to connect to the web-based manager for the rst time.
Conguration changes made with the web-based manager are effective immediately with-
out resetting the FortiBridge unit or interrupting service.
To connect to the web-based manager
1. Connect the management port of the FortiBridge unit to Ethernet port of the manage-
ment computer.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
2. Congure the management computer to be on the same subnet as the FortiBridge
management port interface.
To do this, change the IP address of the management computer to 192.168.1.2 and
the netmask to 255.255.255.0.
3. To access the FortiBridge web-based manager, in your browser, go to
https://192.168.1.99.
4. Type admin in the Name eld and click Login.
To congure Probes
Probes monitor the FortiGate unit by sending packets from the INT 2 interface through
the FortiGate unit to the EXT 2 interface. If probe packets are not received at the EXT 2
interface the FortiBridge unit detects a failure.
Congure probe settings to set actions on failure, add a dynamic IP pattern used by the
probe packets, and enter the serial number of the FortiGate unit. Actions on failure can
include failing open and sending an alert email, a syslog message, and an SNMP trap.
1. Go to Probe > Settings.
2. Enter the Probe IP address pattern (#.#.#.*).
3. Enable ping, HTTP, FTP, POP3, SMTP, and/or IMAP probes.
4. Set the Port Number for each protocol.
5. Change the Failure Threshold and probe Interval for each probe.
To set up Notications
1. Go to Probe > Notications.
2. Enter a Notication Message Tag.
3. Optionally, select the Syslog check box and enter the IP address, port and facility of
the Syslog server that receives FortiBridge syslog messages.
4. Optionally, select the Email check box and enter the SMTP server, email addresses,
SMTP user name, and password of the users to send the alert email.
5. Optionally, select the SNMP check box and enter the name, hosts, and traps of the
SNMP manager to send alerts to a community.
To congure the Management, Default Gateway, and Primary and Secondary DNS server
IP addresses
1. Go to System > Status > Management Port area and click Change.

LED DescriptionPackage Contents
FortiBridge 2001F
USB
CONSOLE MODEM MGMT
INT1
INT2
INT1
INT2
EXT1
EXT2
EXT1
EXT2
HA
PWR NORMAL
BYPASS
MODE RESET
FortiGate
DISCONNECT POWER SUPPLY CORD BEFORE
SERVICING
Ground
AC power
connection
Power button
USB
Console
Modem
Management
LEDs
INT1 and
INT2
EXT1 and
EXT2
Mode
Reset
LEDs
Interface Description
Connecting
Administrator user name admin
Administrator password (none)
NAT/Route mode
Management 192.168.1.99
To reset the unit to the factory defaults, in the CLI type the command:
execute factory reset
FortiGate-30B
Tools and Documenation
Copyright 2010 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
QuickStart Guide
Straight-through
Ethernet cable
Power cable
DB9-RJ45 Serial
cable
REGISTER
SFP SX x2
INT3 EXT3
FortiBridge2001F
USB
CONSOLE MODEMMGMT
INT1
INT2
INT1
INT2
EXT1
EXT2
EXT1
EXT2
HA
PWRNORMAL
BYPASS
MODE RESET
FortiGate
Factory Defaults
LED State Description
Power Green The unit is powered on.
Off The unit is powered off.
Normal Green The unit is being used in Normal
mode.
HA Green The unit is being used in a HA cluster.
Off The unit is in stand-alone mode.
Bypass
Green Bypass network activity at this inter-
face.
Off Normal status.
INT and
EXT LEDs
Green The correct cable is in use and the
connected equipment has power.
Off No link established or the interface
has been turned off.
MGMT
Port
Link/Activity (left) Green Port has power and network connec-
tion.
Link/Activity (left) Green
ashing
Network data is being sent or re-
ceived.
Speed (right) indicator is
Green
Connected at 1000 Mbps.
Speed (right) indicator is
Amber
The interface is connected at 100
Mbps.
Speed (right) indicator
is Off
The interface is connected at 10
Mbps.
Interface Type Speed Proto-
col
Description
Console RJ-45 9600 bps
8/N/1
RS-232
serial
Connection to the
management computer.
Provides access to the
command line interface
(CLI).
Modem RJ-45 Connection to external
serial modem with full
handshaking.
USB USB USB Two optional connec-
tions to a USB key for
installation.
MGMT RJ-45 10/100/1000
Base-T
Ethernet Two management ports.
INT1 and EXT1 LC
SFP
1000Base-SX Ethernet Fiber optic connec-
tions to gigabit optical
networks.
INT2 and EXT2 SFP 1GB-SX Ethernet Small form-factor plug-
gable transceiver.
Connect the FortiBridge unit to the internal and external networks and the Forti-
Gate unit. Normally, you would use straight-through ethernet cables to connect
the FortiBridge unit. However, for some connections you may need a crossover
ethernet cable (for example, for compatibility with network devices that do not
support Auto MDI/MDIX).
• Connect the FortiBridge INT 2 interface to the FortiGate unit internal inter-
face.
• Connect the FortiBridge EXT 2 interface to the FortiGate unit external inter-
face.
• Connect the FortiBridge INT 1 interface to the internal network.
• Connect the FortiBridge EXT 1 interface to the external network.
• Turn on the FortiGate unit and any network equipment that was turned off.
• Connect the power cord at the back of the FortiBridge unit. Plug the other
end of the power cable into a grounded electrical outlet.
• The PWR and Bypass Mode LEDs turn on. After a short time, the Forti-
Bridge unit switches to Normal mode. The Bypass LED turns off and the
Normal LED turns on.
Note: To ground the unit, use a minimum of 18 AWG (UL Certication) wire with
ring terminals. One end connects to the ground on the back of the unit and the
other end connects to the bracket on the chassis.
Caution: Disconnect power source before servicing.