Fortinet FortiGate Rugged 60F Series User manual

QuickStart Guide
FortiGate Rugged 60F Series
FGR-60F and FGR-60F-3G4G

3
Before you begin
Please register your device to access fortiguard updates, cloud management,
firmware upgrades, technical support, and warranty coverage.
For technical documentation such as administration guides, reference manuals,
and release notes, please visit:
http://support.fortinet.com
http://docs.fortinet.com
Thank you for choosing Fortinet.
August 16, 2022
Copyright© 2022 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, FortiCare® and FortiGuard®, and certain other marks are registered trademarks
of Fortinet, Inc., in the U.S. and other jurisdictions, and other Fortinet names herein may also be registered and/or common law trademarks of Fortinet. All
other product or company names may be trademarks of their respective owners. Performance and other metrics contained herein were attained in internal
lab tests under ideal conditions, and actual performance and other results may vary. Network variables, different network environments and other conditions
may affect performance results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or
implied, except to the extent Fortinet enters a binding written contract, signed by Fortinet’s General Counsel, with a purchaser that expressly warrants that
the identified product will perform according to certain expressly-identified performance metrics and, in such event, only the specific performance metrics
expressly identified in such binding written contract shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to performance
in the same ideal conditions as in Fortinet’s internal lab tests. In no event does Fortinet make any commitment related to future deliverables, features or
development, and circumstances may change such that any forward-looking statements herein are not accurate. Fortinet disclaims in full any covenants,
representations, and guarantees pursuant hereto, whether express or implied. Fortinet reserves the right to change, modify, transfer, or otherwise revise this
publication without notice, and the most current version of the publication shall be applicable.
2For Product License Agreement / EULA and Warranty Terms, visit https://www.fortinet.com/content/dam/fortinet/assets/legal/EULA.pdf

54
BYPASS
STATUS
HA
POWER
FortiGate Rugged 60F
CONSOLE 1 2
SFP1
SFP2
SFP2WAN1
BYPASS
WAN2
3 4CONSOLE 1 2
SFP1
SFP1
SFP2
SFP2WAN1
BYPASS
Shared
Shared
WAN2
3 4
BYPASS
STATUS
HA
POWER
FortiGate Rugged 60F
CONSOLE 1 2
SFP1
SFP2
SFP2WAN1
BYPASS
WAN2
3 4CONSOLE 1 2
SFP1
SFP1
SFP2
SFP2WAN1
BYPASS
Shared
Shared
WAN2
3 4
1x QuickStart Guide 2x Ferrite Cores
4x Extended Rubber Feet
FortiGate Rugged 60F
Box Includes- FGR-60F
1x CAT5e Ethernet Cable
1x Wall Mount Bracket
Front Panel - FGR-60F
3
4
1
2
2
3
4
1
Console (RJ-45) CLI management computer connection
Ethernet Ports 1 to 4 (RJ-45) 1 Gbps Ethernet connections
56 7
USB (USB A) USB 2.0 server port
2x DC Power Connectors 1x DIN Rail Bracket
BYPASS
POWER
STATUS
HA
Green: PHY mode
Green: Device is on
Green: Operating normally
Green: HA enabled (normal)
Red: Bypass mode
Off: Device is off
Amber: Device error
Amber: HA enabled (failover)
Off: HA disabled
Flashing Green: Device startup
FGR-60F
BYPASS
STATUS
HA
POWER
FortiGate Rugged 60F
USB
CONSOLE 1 2 SFP1
SFP1
SFP2
SFP2WAN1
BYPASS
WAN2
3 4
5
6
7
Shared WAN1 & WAN2 Ports (RJ-45) 1 Gbps Ethernet connections
Shared SFP1 & SFP2 Ports (SFP) 1 Gbps Ethernet connections
LAN/WAN Bypass (RJ-45) 1 Gbps Ethernet connections
Speed
Link/Act
Ethernet & WAN Link/Act
Green: Connected
Flashing Green: Data activity
Off: No link established
Ethernet & WAN Speed
Green: Connected at 1000Mbps
Amber: Connected at 100Mbps
Off: 10Mbpps or no link established
Green: Connected at 1000Mbps
Off: No link established
Flashing Green: 1000Mbps activity
SFP Speed
SFP LED Indicators
Ethernet LED Indicators
SFP Activity
NOTE: WAN1/WAN2 and SFP1/SFP2 are shared interfaces
Wall Mount & Bracket Scews
(1 set of Bracket Screws for the DIN or Wall Bracket)

76
SERIAL
RESET
+ - + -
DC2 12-125V DC1 12-125V
DC1
DC2
Rear Panel - FGR-60F
2 3 4 6
5
1
1
2
3
4
5
6
RESET button
Ground Screw (#12 AWG) optional ground connection
Earth Ground (Lug Plate) ground connection
SERIAL Port (DB9) RS232 connection
Power Supply Indicators (DC1 & DC2) By default, Alarm is enabled in the OS*
Power Terminals (2 Pin Male) Redundant failover, 12V to 125V DC, 2A Max, see pg12
FGR-60F
Green: Power supply is on
Red: Alarm is on*; power supply not providing power or not connected
Off: Power supply is off
Green: Power supply is on
Red: Alarm is on*; power supply not providing power or not connected
Off: Power supply is off
DC1
DC2

98
BYPASS
STATUS
HA
LTE
DIV MAINGPS
SIM1
SIM2
POWER
FortiGate Rugged 60F 3G4G
CONSOLE 1 2
SFP1
Shared
Shared
SFP1
SFP2
SFP2WAN1
BYPASS
WAN2
3 4
1x QuickStart Guide 3x Antennae
4x Extended Rubber Feet
BYPASS
STATUS
HA
LTE
DIV MAINGPS
SIM1
SIM2
POWER
FortiGate Rugged 60F 3G4G
CONSOLE 1 2
SFP1
Shared
Shared
SFP1
SFP2
SFP2WAN1
BYPASS
WAN2
3 4
FortiGate Rugged 60F 3G4G
Box Includes - FGR-60F-3G4G Front - FGR-60F-3G4G
1x CAT5e Ethernet Cable
Wall Mount & Bracket Scews
(1 set of Bracket Screws for the DIN or Wall Bracket)
1x Wall Mount Bracket
2x DC Power Connectors,
2x Ferrite Cores
1x DIN Rail Bracket
3
4
1
2
2
3
4
1
Console (RJ-45) CLI management computer connection
Ethernet Ports 1 to 4 (RJ-45) 1 Gbps Ethernet connections
56 7 8
USB (USB A) USB 2.0 server port
BYPASS
POWER
SIM1
SIM2
STATUS
HA
LTE
Green: PHY mode
Green: Device is on
Green: SIM1 is detected
Green: SIM2 is detected
Green: Operating normally
Green: HA enabled (normal)
Green: 4G service is on
Red: Bypass mode
Off: Device is off
Off: SIM1 is not detected
Off: SIM2 is not detected
Amber: Device error
Amber: HA enabled (failover)
Amber: 3G service is on
Off: HA disabled
Off: 3G/4G service is off
Flashing Green: Device startup
5
6
7
8
Shared WAN1 & WAN2 Ports (RJ-45) 1 Gbps Ethernet connections
Shared SFP1 & SFP2 Ports (SFP) 1 Gbps Ethernet connections
LAN/WAN Bypass (RJ-45) 1 Gbps Ethernet connections
Ethernet & WAN Link/Act
Green: Connected
Flashing Green: Data activity
Off: No link established
Ethernet & WAN Speed
Green: Connected at 1000Mbps
Amber: Connected at 100Mbps
Off: 10Mbpps or no link established
Green: Connected at 1000Mbps
Off: No link established
Flashing Green: 1000Mbps activity
SFP Speed
SFP Activity
NOTE: WAN1/WAN2 and SFP1/SFP2 are shared interfaces
Antenna Connection (3x SMA) WWAN antenna connections
FGR-60F-3G4G

1110
Rear - FGR-60F-3G4G SIM Slots - FGR-60F-3G4G
FGR-60F-3G4G
231
2 SIM 1
231
2 SIM 1
231
2 SIM 1
231
2 SIM 1
SIM1
Primary(1)
SIM2
Secondary(2)
SERIAL
RESET
+ - + -
DC2 12-125V DC1 12-125V
DC1
DC2
SIM1
SIM2
SERIAL
RESET
+ - + -
DC2 12-125V DC1 12-125V
DC1
DC2
SIM1
SIM2
SERIAL
RESET
+ -
DC 12-125V
SIM1
SIM2
SERIAL
RESET
+ -
DC 12-125V
SIM1
SIM2
SERIAL
RESET
+ -
DC 12-125V
SIM1
SIM2
SERIAL
RESET
+ -
DC 12-125V
SIM1
SIM2
1 2 3 4
NOTE: For more information on Wireless WAN Configuration, please
refer to the FortiOS Handbook at docs.fortinet.com
5
5SIM Slots (2x Micro SIM) SIM card slots
231
2 SIM 1
2 3 4 7
6
1
1
2
3
4
RESET button
Ground Screw (#12 AWG) optional ground connection
Earth Ground (Lug Plate) ground connection
SERIAL Port (DB9) RS232 connection
6
7
Power Supply Indicators (DC1 & DC2) By default, Alarm is enabled in the OS*
Power Terminals (2 Pin Male) Redundant failover, 12V to 125V DC, 2A Max, see pg12
Green: Power supply is on
Red: Alarm is on*; power supply not providing power or not connected
Off: Power supply is off
Green: Power supply is on
Red: Alarm is on*; power supply not providing power or not connected
Off: Power supply is off
DC1
DC2

1312
Installation
Installation
Power Connections
Warnings
• The DC input supports negative ground (+12V to +125V DC) and
positive ground (-12V to -125V DC) power sources
• Terminal +(A) is the high voltage potential pin and Terminal -(B) is
the lower voltage potential pin
• Do not connect +(A) to a lower voltage potential than -(B)
• The voltage between +(A) and -(B) must be +12V to +125V DC
• Consult a professional electrician to install the device and
determine a suitable wire gauge and length
• The DC terminal block wire gauge maximum is 12 AWG; the
minimum is 30 AWG
• Connect earth ground using the lug plate or grounding screw
• Install the supplied ferrite cores, see pg14
1. Connect +(A) of the device terminal block to the DC power source,
then connect the negative -(B) of the terminal block
2. Secure the earth ground terminal of the device to chassis
ground or earth ground
SERIAL
RESET
+ - + -
DC2 12-125V DC1 12-125V
DC1
DC2
SIM1
SIM2
GND
3. Insert the wired terminal block into the power connector on the device
SERIAL
RESET
+ - + -
DC2 12-125V DC1 12-125V
DC1
DC2
+(A)
+(A)
+(A) -(B)
-(B)
-(B)
DC Input Power +(A) Terminal -(B) Terminal
Negative Ground +12V to +125V DC Ground
Positive Ground Ground -12V to -125V DC
OPTIONAL: The FGR-60F Series have optional dual DC inputs for failover
redundancy. If a DC input fails, the second input will supply power.

1514
Installation
Internet
Ethernet Cable
WAN port
1. Connect the WAN port to an Internet connection using the provided
Ethernet cable
SFP Ports
To install the SFP transceivers:
1. Slide the SFP into the cage socket until it clicks into place
2. Lift the latch to lock the SFP
To install the supplied ferrite cores:
1. Open a ferrite core and loop the power cables around
2. Ensure there is 100mm(3.9in) to 150mm(5.9in) distance between the
ferrite core and power connector, then close the ferrite core
Tx
Rx
Cage Socket
Looped Ferrite Core
Power Cable Distance
100mm(3.9in)  150mm(5.9in)
Cage Socket
Latch
SFP
SFP
1
1
2
2
To remove the SFP transceivers:
1. Lower the latch to unlock the SFP
2. Carefully pull the SFP out of the cage socket
Internet Connections
Ferrite Core Installation
1
2

1716
Installation
Wall Mount Option
To attach the unit to a wall:
1. Mark the location on the wall where the anchors will be located
2. Drill holes into the wall, then insert the provided anchors into the holes
3. Screw the two screws provided into the two anchors, leaving enough of
the screw exposed to ensure that the unit can be mounted
4. Connect the wall mount bracket to the bottom of the device using the
provided bracket screws
5. Mount the device onto the screws and ensure that it is mounted
securely
Wall Mount Bracket
Bracket Screw
FortiGate
Wall
Wall Mount Bracket
Wall Mount
Screw
Wall
Mount Anchor
FortiGate
WARNING: To ensure adequate air flow, the minimum radiating
distance between mounted devices is 100mm(3.9in)
The FortiRugged-60F supports DIN rails with 35mm(1.4in) x 15mm(0.6in)
and 35mm(1.4in) x 7.5mm(0.3in) sizes . The minimum radiating distance
between DIN rail devices is 100mm(3.9in).
1. Connect the DIN rail bracket to the bottom of the device using the
provided bracket screws. Note there are 4 available bracket positions.
2. Position the bottom of the device directly in front of the DIN rail, ensuring
that the top of the DIN rail bracket hooks over the top of the DIN rail
3. Rotate the device until the bottom of the DIN rail bracket sits against the
bottom of the DIN rail
DIN Rail Option
DIN Rail Bracket
Bracket Screw
FortiGate
DIN Rail Bracket
DIN Rail
FortiGate
DIN Rail Bracket
DIN Rail
FortiGate
Multiple DIN Bracket Positions

1918
Installation
Desktop / Extended Feet Option
1. Place the unit on a flat, clean and stable surface
2. Ensure there is at least 38mm(1.5in) of clearance for adequate airflow
3. Plug the provided power cable into the rear of the unit and then into a
grounded electrical outlet or separate power source
38mm(1.5in)
Your device is already equipped with feet for a flat surface. You can
optionally install the extended grey feet for more surface clearance.
38mm(1.5in)
38mm(1.5in)
38mm(1.5in)
Rack/Rail Mount Option
Fortinet carries a variety of standard and custom rack and rail mount
accessories, including a rack mount tray kit, SP-RACKTRAY-02.
SP-RACKTRAY-02