Fortinet FortiAP 222E User manual

FortiAP 222E
QuickStart Guide

1/31/2018
Copyright© 2018 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®,
FortiCare® and FortiGuard®, and certain other marks are registered trademarks of Fortinet,
Inc., in the U.S. and other jurisdictions, and other Fortinet names herein may also be
registered and/or common law trademarks of Fortinet. All other product or company names
may be trademarks of their respective owners. Performance and other metrics contained
herein were attained in internal lab tests under ideal conditions, and actual performance and
other results may vary. Network variables, different network environments and other
conditions may affect performance results. Nothing herein represents any binding
commitment by Fortinet, and Fortinet disclaims all warranties, whether express or implied,
except to the extent Fortinet enters a binding written contract, signed by Fortinet’s General
Counsel, with a purchaser that expressly warrants that the identified product will perform
according to certain expressly-identified performance metrics and, in such event, only the
specific performance metrics expressly identified in such binding written contract shall be
binding on Fortinet. For absolute clarity, any such warranty will be limited to performance in
the same ideal conditions as in Fortinet’s internal lab tests. In no event does Fortinet make
any commitment related to future deliverables, features, or development, and circumstances
may change such that any forward-looking statements herein are not accurate. Fortinet
disclaims in full any covenants, representations,and guarantees pursuant hereto, whether
express or implied. Fortinet reserves the right to change, modify, transfer, or otherwise
revise this publication without notice, and the most current version of the publication shall be
applicable.

Cautions and Warnings
Environmental specifications
Ambient operating temperature: 0C to 40C
Refer to specific Product Model Data Sheet for Environmental
Specifications (Operating Temperature, Storage Temperature,
Humidity, and Altitude).
Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales
(Température de fonctionnement, température de stockage, humidité et l'altitude).
Safety
Caution: This equipment is to be used in a Network Environment 0 per IECTR
62101. This product is connected only to PoE networks without routing to the
outside plant.
Attention: Ce matériel doit être utilisé dans un Environnement Réseau 0 par
IECTR 62101. Ce produit est uniquement connecté aux réseaux PoE sans
installation externe de routage.
QuickStart Guide

Box Includes
FortiAP device QuickStart Guide
PWR PoE LAN
SEN O
V
SEN O
SEN O
Mounting Hardware: Pole-Mount
Bracket, Wall Mount Base, and Mount
Kit: Mounting Screws (X8), Bolts (X4),
and Pole-Mount Straps (X2)
PoE injectorEPA5006GPR Antennae:
2.4G (X2),
5G(X2),
and BLE
(X1)
4

Grounding Screw Grounding cable
(X1) AC Power Cord (US)
5

Before YouBegin
Write down details typically provided by your network administrator or ISP.
Static IPaddress
IPaddress ___________________
Subnet Mask ___________________
Default Gateway ___________________
Primary/Secondary DNS ___________________
DHCP
It is normal to not require a hostname, but your ISP might require it.
Hostname ___________________
QuickStart Guide Video
https://video.fortinet.com/video/177/
fortigate-and-fortiap
6

FortiAP 222E - Device Front
FortiAP 222E
Device Guide
7

FortiAP 222E - Device Rear
2.4 GHz
Antenna
5.0 GHz
Antenna
5.0 GHz
Antenna
2.4 GHz
Antenna
8

FortiAP 222E - LED Definitions
O: Not connected
Green: Connected
Blinking: Transmitting and receiving data
LAN
O: No link detected or disabled
Green: 5GHz wireless radio enabled
Blinking: Transmitting and receiving data
5.0GHz
O: The unit is o
Green: The unit is on
Green Blinking: The unit is booting up
Power
O: No link detected or disabled
Green: 2.4GHz Wireless Radio enabled
Blinking: Transmitting and receiving data
2.4GHz
9

Installation
The unit can be mounted on a wall or ceiling using
the mounting hardware provided.
The electrical wall box must be pre-installed.
10

A
Antennae
The FortiAP 222E unit provides dual
concurrent radio signals. Use the
top antenna mounts to access the
Radio 1 (802.11 b/g/n at 300Mbps)
signals, and the bottom antenna
mounts (near the waterproof PoE
connector) to access the Radio 2
(802.11 a/n/ac at 867Mbps) signals.
To use both radio frequencies
concurrently, use all four WiFi
antennae.
To install the WiFi antennae
1. Insert the antennae base firmly
into the appropriate antenna
mount.
2. Securely hand tighten the
fastening collar.
3. Repeat for the remaining
antennae.
11

B
Cabling
The unit requires 48VDC power, which is delivered by the PoE injector over a
straight-through Ethernet cable.
To install the weatherproof connector
1. Unscrew the coupling ring from the waterproof connector, remove the
sealing gland, and thread the RJ-45 plug through the connector
components.
2. Insert the RJ-45 plug into the PoE port on the unit and install the
weatherproof panel connector onto the threaded coupling at the port.
3. Slide the sealing gland along the cable into the panel connector.
4. Thread the coupling ring into the panel connector and tighten it until the
sealing gland is compressed, making a watertight seal on the cable.
12

FortiAPSetup
Deployment through a FortiGate
Ensure that you are running the Fortinet recommended version of
software. Please check support.fortinet.com for more information.
If FortiGate is on the same network as the FortiAP:
1. Use FortiGate to preauthorize the FortiAP device.
2. Refer to the “Access Point Deployment” section of the FortiWiFiand
FortiAP Configuration Guide found at http://forti.net/ap-docs.
3. Plug the FortiAP into your local Ethernet connection. The FortiAP will self-
configure.
Or
1. Instead of preauthorizing, you can use the FortiGate to authorize the
FortiAP device after you have connected the FortiAP to the network.
2. Within two minutes of connecting the FortiAP to the FortiGate, the device
appears on the Managed FortiAP page in the Web-based Manager:
authorize and assign a profile to the device.
13

If FortiGate is not on the same network as the FortiAP:
1. Log into FortiAP directly (IP address: 192.168.1.2) with username admin
and no password, and specify the IP address of the controlling FortiGate.
2. Connect to FortiAP via the CLI using the instructions in the “Connecting
to FortiAP CLI” section of the FortiWiFi and FortiAPConfiguration guide.
3. Specify the IP address of the controlling FortiGate:
cfg -a AC_IPADDR_1=0.0.0.0
cfg -c
where 0.0.0.0 is the address of the FortiGate.
4. The FortiAP device connects to FortiGate, and then you can authorize the
FortiAP.
14

Cautions and Warnings
Environmental specifications
Ambient operating temperature: -30C to 60C
Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature,
Storage Temperature, Humidity, and Altitude)
Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales (Température
de fonctionnement, température de stockage, humidité et l'altitude).
Safety
Warning: Equipment intended for installation in Restricted Access Location.
Avertissement: Le matériel est conçu pour être installé dans un endroit où l’accès est restreint.
Caution: This equipment is to be used in a Network Environment 0 per IECTR 62101. This product is
connected only to PoE networks without routing to the outside plant.
Attention: Ce matériel doit être utilisé dans un Environnement Réseau 0 par IECTR 62101. Ce produit
est uniquement connecté aux réseaux PoE sans installation externe de routage.
This product is intended to be supplied 48-57 Vdc from PoE source.
Le produit doit être alimenté par à de 48-57 Vdc (PoE).
Grounding — To prevent damage to your equipment, connections that enter from outside the building
should pass through a lightning / surge protector, and be properly grounded. Use an electrostatic
discharge workstation (ESD) and/or wear an anti-static wrist strap while you work. In addition to the
grounding terminal of the plug, on the back panel, there is another, separate terminal for earthing.
Mise à la terre — Pour éviter d’endommager votre matériel, assurez-vous que les branchements qui
entrent à partir de l’extérieur du bâtiment passent par un parafoudre / parasurtenseur et sont
correctement mis à la terre. Utilisez un poste de travail de décharge électrostatique (ESD) et / ou portez
15

un bracelet anti-statique lorsque vous travaillez. Ce produit possède une borne de mise à la terre qui
est prévu à l’arrière du produit, à ceci s’ajoute la mise à la terre de la prise.
This product has a separate protective earthing terminal provided on the back of the product in
addition to the grounding terminal of the attachment plug. This separate protective earthing terminal
must be permanently connected to earth with a green with yellow stripe conductor minimum size # 14
AWG and the connection is to be installed by a qualified service personnel.
Ce produit a une borne de mise à la terre séparé sur le dos de l'appareil, en plus de la borne de mise à
la terre de la fiche de raccordement. Cette borne de mise à la terre séparée doit être connecté en
permanence à la terre avec un conducteur vert avec la taille bande jaune de minimum # 14 AWG et la
connexion doit être installé par un personnel qualifié.
The connecting cable between the outdoor equipment and the indoor ITE devices should comply with
Class 3 wiring methods as listed in NEC, Table 725.154(G) for Class 3 Cable Substitutions.
Le câble connectant l’équipement extérieur et ceux d’intérieur de type ITE doit être conforme avec les
méthodes de câblage de classe 3 tel que listé dans le standard NEC, Table 725.154(G) pour les câbles
de substitutions de classe 3.
PoE input cable type should be CL3, CL3P, CL3R, CL3X, marked "SUNLIGHT RESISTANT", "SUN.
RES.", or "SR." and "water resistant" or "W".
Le type de câble PoE d'entrée doit être CL3, CL3P, CL3R, CL3X marqué "SUNLIGHT RESISTANT".
"SUN RES.» Ou «SR». et "waterproof" ou "W".
If further assistance is needed with purchasing a power source and POE input cable, please contact
Fortinet, Inc.
Si vous avez besoin de plus d'aide à l'achat de l'alimentation et le fil d'entrée PoE, s'il vous plaît
communiquer avec Fortinet, Inc.
The Console port is not intended to be connected to the computer after the outdoor installation is
completed.
16

La porte Console n’est pas destinée à être raccordée à l’ordinateur après l’installation extérieure faite.
This equipment is to be connected only to PoE networks (LPS) and maybe installed outdoors except
the Surge Protector, the PoE Injector and its external LPS Power Supply which are intended for indoor
installation only.
Ce produit doit être connecté uniquement aux réseaux POE et peut être installé à l'extérieur sauf le
protecteur de surtension, l'injecteur PoE et son alimentation LPS externe qui sont destinés à une
installation intérieure seulement
Regulatory Notices
Federal Communication Commission (FCC) – USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
17

WARNING: Any changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 28cm between the radiator
and your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Industry Canada Equipment Standard for Digital Equipment (ICES) –
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development (ISED) – Canada
This device complies with ISED license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d' ISED applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être
exploités. Sélection d'autres canaux n'est pas possible.
18

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 28cm between the radiator &
your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 28cm de
distance entre la source de rayonnement et votre corps.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point
operation as appropriate.
Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz)
doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point,
selon le cas.
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-channel mobile satellite systems. High-power radars are allocated as
primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these
radars could cause interference and/or damage to LE-LAN devices.
Attention: Le dispositif de la bande 5150-5250 MHz est réservé à un usage intérieur afin de réduire
l'interférence nuisible potentielle aux systèmes mobiles par satellite co-canal. Les radars à haute
puissance sont désignés comme utilisateurs principaux (à savoir les utilisateurs prioritaires) des
bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interférences et /
ou endommager les périphériques LE-LAN
This device has been designed to operate with an antenna having a maximum gain of 5 dBi for 2.4GHz
and 7 dBi for 5GHz. Antenna having a higher gain is strictly prohibited per regulations of ISED. The
required antenna impedance is 50 ohms.
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference
19

to other users, the antenna type and its gain should be so chosen that the equivalent isotopically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de 5 dBi pour 2,4
GHz et 7 dBi pour 5GHz. Une antenne ayant un gain supérieur sont strictement interdites par la
réglementation d'ISED. L'impédance d'antenne requise est de 50 ohms.
Conformément à la réglementation d'ISED, cet émetteur radio peut fonctionner seulement avec une
antenne d’un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par ISED. Dans le but
de réduire les risques de brouillage radioélectrique aux autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l'intensité nécessaire à l'établissement d'une communication réussie.
This radio transmitter (7280B-141703) has been approved by ISED to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (7280B-141703) a été approuvé par ISED pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur
au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
This device and it's antennas(s) must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une
autre antenne ou transmetteur.
20