Fortis FST1WLKPADA User manual

T1 ULTRA SLIM WALKING
SMART TREADMILL
FST1WLKPADA

• When you start training with this product, please consider your physical condition,
train properly and regularly to ensure that you have enough physical strength to
train. Wrong or excessive training will not help your health.
• This product is not suitable for children. Children can use the product, but only
under the supervision of adults. The device is not a toy.
• Only people who have a good understanding of the product and are very healthy
should use the device.
• This product is suitable for home use, not suitable for professional training and
testing, or medical purposes. If the power line is damaged, it must be replaced by
the manufacturer or a qualified service person in order to avoid danger.
• Please check all parts before use. And make sure the screws and nuts are
tightened.
• When running on a treadmill, wear comfortable tight clothes to avoid clothes being
caught by the machine. Do not let children or pets to play around the treadmill to
avoid accidents.
• Place the treadmill on a smooth, clean, level surface. Make sure there are no sharp
objects nearby. Do not use it near water and heat sources.
• Please keep your hands away from all moving parts. Do not place your hands and
feet in the gap below the running belt.
• The treadmill must have only one user at a time.
• Make sure the screws and bolts are tightened after the treadmill is assembled.
• If the product is not in use, put the machine in a safe place to prevent the danger
caused by children and those who are not suitable for using the treadmill.
• When in an emergency, quickly pull down the safety switch and step on the left
and right side of the treadmill.
• Place the treadmill well before use, the side of the left and right handrails needs
one metre safety distance, the back needs two metres. There should be no
obstacles in the safe distance.
• Please use the accessories provided by the original manufacturer and it is strictly
forbidden to change it privately.
• The product is a HC grade product with a maximum user weight of 100kgs.
• The running belt on this treadmill has a visible joint mark. This is completely
normal and will not affect the performance or operation of your treadmill.
SAFETY & WARNINGS
Note:
Ensure you have read and fully understand the instructions for this device. Failure to do so
could cause, damage or serious harm.

Special Notice
• Place the treadmill in a place where the plug can be plugged into the socket.
• Plug the device into a socket and ensure it is not loose.
• Ensure the socket has been installed professionally.
• If the plug and socket are not compatible, please do not change the plug by
yourself. Ask an electrician to handle it.
• Please use a supply voltage of 240V.
• Please do not let the power cord touch the running belt roller, and do not use a
damaged plug.
• Unplug the plug from the socket before cleaning and maintenance.
•
WARNING:
if the plug is not pulled out, it may lead to personal injury and
equipment damage.
• Please check each part carefully before use.
• Please do not use this product outdoors, in high humidity and in the sun.
• Please turn off the machine and remove the plug when you leave.
• For your safety, the power plug of the machine must be grounded.

Tr e a d m i l l
Silicone oil (x2)
Cushion (x4)
Remote controller
Installation tool
COMPONENTS

OVERVIEW

No.
Name
Quantity
No.
Name
Quantity
1.
Main Frame
1
23.
Oil Pipe Bushing
1
2.
Motor Base
1
24.
Poly V-Belt
1
3.
Front Roller
1
25.
Rubber Gasket
10
4.
Rear Roller
1
26.
Silicone Oil Tank
1
5.
Running Board
1
27.
Silicone Refuelling Tube
1
6.
Running Belt
1
28.
Wireless Governor
1
7.
Dc Motor
1
29.
Silicone Oil L-Shaped Hex
1
8.
Electronic Meter
PCB
1
30.
L-Shaped Hex Wrench
6mm
1

9.
Controller
(Lower
Controller)
1
31.
Cross Open End Wrench
1
10.
Communication
Line
1
32.
Flat Gasket Ø8.5
7
11.
Power Line
1
33.
Spring Gasketø8.5
2
12.
Power Line
Buckle
1
34.
Locknut M8
2
13.
Motor Cover
(Upper)
1
35.
Cylindrical Head In
Hexagonal Screw M8*55
5
14.
Motor Cover
(Lower)
1
36.
Cylindrical Head In
Hexagonal Screw M8*12
2
15.
Rear Ta i l C o ve r
1
37.
Semicircular Head In
Hexagonal Screw M8*35
2
16.
Left Border
1
38.
Countersunk Head In
Hexagonal Screw M8*25
8
17.
Right Border
1
39.
Cross Recessed Pan Head
Combination Screw M4
1
18.
Moving Wheel
1
40.
Cross Groove Pan Head
Self Attack Self Drilling
Screw ST4.2*16
17
19.
Border Buckle
2
41.
Cross Groove Pan Self
Drilling Screw ST4.0*16
20
20.
R-Shaped Line
Buckle
8
42.
Cross Groove Pan Self
Drilling Screw ST4.0*12
4
21.
Oil Cover
1
43.
Cross Groove Pan Self
Drilling Screw ST3.0*10
2
22.
Shock
Absorption Pad
2
44.
Instructions Manual
1

The main structure of the treadmill you purchased has already been assembled in the
factory. It can simply be used when plugged in. The following operations are how to use
handrails and how to fold and unfold them.
1. Lift the treadmill out of the box and placed it on a level surface. (Make sure the
front and back of the treadmill has 50cm space for folding and running power lines.
etc.)
2. As shown below, the tail of the treadmill can be raised with both hands to move
forward and backward, which is only suitable for short-distance movement within
the room.
3. Plug in the power, turn on the switch and enjoy the exercise.
INSTALLATION

LED window display
"SPEED" Window:
Displays the current speed. The speed display range is: 0.8-6.0km/h. When the countdown
is started, "3", "2" and "1" are displayed.
“TIME” Window:
Display’s the exercise time. The time is from 0:00-99:59. When the time is 99:59, the
treadmill speed steadily decreases until it stops running.
The countdown mode will decrease from the set time to zero. When the countdown is 0:00,
the treadmill speed steadily decreases until it stops running and completely stops after 10
minutes, later enters the standby state.
“DIS” Window:
Displays the distance travelled, from 0.00-99.90. It will begin to re-count after the maximum
is exceeded.
The countdown mode will decrease from the set value to zero, when the countdown reaches
0, the treadmill speed steadily decreases until it stops running and completely stops after 10
minutes, then it will enter standby mode.
“CAL” Window:
Display the calorie consumption value. When the calorie consumption value is displayed,
the positive count is from 0.0-999.0, re-count after overflow. When the count is reversed, it is
counted from the set value to 0. When the countdown reaches 0, the treadmill speed
steadily decreases until it stops running and completely stops after 10 minutes, later enters
the standby state.
OPERATION

Remote Button Function
• “□” is start/stop button: This button can be used to stop the treadmill from running
state and reset to zero during exercise. Use this button also as the start button
when the power is on.
• "+" is speed increasing button: Adjust the speed after the treadmill starts, its
adjustment range is 0.1 km/time and it continues to increase when it is held for
more than 1 second.
• "-” is speed decreasing button: Adjust the speed after the treadmill starts, the
adjustment range is 0.1 km/time and continues to decrease when it is held for more
than 1 second.
Operation during exercise:
• Pressing the "-" button will slow down speed of the treadmill.
• Press the “+” button to increase the running speed of the treadmill.
• Press the “□” button to slow down the running speed until it stops running.

APP Guide Operation:
• Download YPOO treadmill APP: Please enter “YPOO” in Apple APP Store or Google
Play. Then you can download the treadmill app freely.
• Create your Account: Enter necessary information to create your sport account.
• Select Training Plan: Select training plan and create a customised plan on the app,
then you can control your treadmill from your smart phone remotely and do your
customized exercise!
Note:
1. You ca n cho ose your loc al language and s et you r local language. You ca n
choose: English, Chinese or Korean.
2. This app will protect your privacy and will not collect any personal
information. Please feel free to use.

Numerical display range:
Setting parameters
Start
Default
Setting range
Display
Range
Time (min : sec)
0:00
-
-
0:00-99:59
Incline (%)
Speed (km/h)
0.8
0.8
0.8- 6.0
0.8- 6.0
Distance (km)
0.00
0.00-99.90
Heart rate (/MIN)
-
N/A
N/A
-
Calorie (Kcal)
0.0
-
-
0.0-999.0
VI. Treadmill Shut down instructions:
The treadmill can be turned off at any time by turning off the power switch so that it does
not damage the treadmill.
VII. Error:
E02
Over voltage protection
E03
Over current protection
E04
Motor open-circuit
E06
Communication error
EOC
Burst protection

Once the treadmill has been run on for 50km cumulatively (about 3 months), maintenance
is needed. Put the lubricating oil (about one third each time) squeezed into the silicone oil
valve and then the running belt will be automatically maintained.
Proper maintenance is the only way to keep your treadmill at its best. Incorrect maintenance
can hurt or shorten the life of the treadmill.
Running belt adjustment
Adjusting the running belt has two functions: Tightening adjustment and the running belt
centre position adjustment. The running belt has been adjusted at the factory. However,
after use, the running belt will be stretched or deviated from the centre plate and cause
damage to the running belt trim strip and the rear cover by friction. It is normal for the
running belt to be stretched during use. When the running belt is slippery or not smooth
during use, you can improve it by adjusting the tightness of the belt.
CLEANING & CARE
Tips:
Do not use sandpaper or solvents to clean the treadmill. The controller part of the
treadmill should not be exposed directly to the sun or moisture to avoid damage.
Please check and tighten all accessories of the treadmill frequently. Damaged parts
must be replaced immediately.

How to adjust the running belt?
1. Adjust the screw on the left side of the belt by Allen Key, turning 1/4 times clockwise
to adjust the rear roller to tight the belt.
2. Repeat step 1 to adjust the right screw. Check that the left and the right screw are
adjusted to the same distance so that the rear roller can be paralleled to the
treadmill frame.
3. Repeat steps 1 and 2 until the running belt does not slip.
4. Note: The running belt can't be adjusted too tightly, which will break the running
belt and increase the pressure of the front and rear rollers, causing problems such
as roller bearing damage and abnormal noise. If you want to reduce the tension of
the running belt, turn the wrench counter clockwise. Note that the left and right
sides are rotated at the same distance.
Adjust the running belt to the middle position
When using the treadmill, the pressure on the running belt is unbalanced because the two
feet exert different forces when running, that causes the belt deviate from the centre. This
deviation is normal. When no one is using the treadmill, the belt goes back to the centre
automatically. If not, you need to adjust it to the centre.
How to adjust the running belt to the middle?
1. Run the treadmill with no-load at a speed of 6km/h.
2. Observe the distance of the running belt to the left and right border. If the running
belt deviates to the left side, turn the left screw clockwise for 1/4 by inner hexagonal
wrench. If the running belt deviates to the right side, turn the right screw clockwise
for 1/4 by inner hexagonal wrench. If the running belt is still not in the centre, repeat
the above the step until it is adjusted to the centre.
3. After adjusting the running belt to the centre, adjust the speed to 1km/h and
observe the deviation of the running belt and check whether there is slipping during
running. If still there is any deviation from the centre, repeat the above steps.
4. Warning! Do not over tighten the roller! This will cause the bearing permanent
damage! If the above steps do not work, you need to tighten the running belt
again.

Colour
Grey
Net weight
29kg
Running belt
45*120cm
Product size
61*150*125cm
Power (W)
600
Speed
0.8-6km/h
Max user weight
100kg
Motorised Walking Treadmill
SPECIFICATION

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com