fossLED FLWP4T User manual

●Output signal: RF(2.4GHz) + DMX512
●Input Voltage: 85-265VDC
●
●Sensitive tunable white and dimmable slider.
●
●When used as an RF controller it can be Paired with multiple receivers.
●
●
- FLWP4T
RF / DMX Control - 4 Zone Tuneable Touch Wall Panel
.
User Guide
Technical Parameters
Remote distance up to 30m within Free Range. Please allow for 12m within
areas restricted by obstacles.
Pairing Guide
Pairing your Wall Panel with each 2.4G RF receiver
● Using the "Match Key"
1. Match: Switch off receiver power, then switch on power again,
short press zone key 3 times on the wall panel quickly within 5s after receiver power on,
the link has been completed once the connected LED lights flash 3 times.
Repeat this process to link further receivers to the wall panel.
2. To Delete a match: Switch off power to the receiver, then switch on power again,
short press the zone key you are deleting 5 times on the remote within 5s after power on,
the unlink has been completed once the connected LED lights flash 5 times.
.
Key Functions
Dimensions
Features
●
●
●
Light Type: Tuneable White
Size: 86x86x35 mm
62.00 mm
4 Zone Touch panel compatible with both DMX512 (FLDC4Y-DMX) and RF (FLDC4Y) receivers.
Set and save several Scene modes
Features
● At Power Up
Match the controller with our receiver (Without using the Match Key)
1.
Match
:
Switch off receiver power, then switch on power again,
short press zone key 3 times on the remote quickly within 5s after receiver power on,
the link has been completed once the connected LED lights flash 3 times.
2. To Delete a match: Switch off power to the receiver, then switch on power again,
short press the zone key you are deleting 5 times on the remote within 5s after power on,
the unlink has been completed once the connected LED lights flash 5 times.
.
Turn On/O
Lighting in all
Zones
Short press will recall
previously saved scenes. To
save a new scene, hold scene
button for 2s.
Tuneable White / Brightness
Slider
Zone Selection - Short press to
select and turn on lighting in
that Zone. Long press 2s to
turn of the lighting in this
Zone.
Short press multiple Zone keys
quickly to control Zones
simultaneously.
RF Receiver - FLDC4Y
DMX Receiver - FLDC4Y-DMX

Installation Diagram
Typical base as below:
UninstallTouch panelBaseplateBase
Ɣ The product shall be installed and serviced by a qualified person.
Ɣ The product is non-waterproof.
Ɣ Good heat dissipation will prolong the working life of the controller, Please ensure good ventilation.
Ɣ Please check if the output voltage of any power supplies used comply with the working voltage
of the product.
Ɣ Ensure all wire connections and polarities are correct
Ɣ If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself.
Safety Information
Wiring Diagram for DMX 512
L NGNDD+ D-
DMX OUTPUT
I NPUT
110-265VAC
RoHS
Uin=85-265VAC
Iin=Max 0.1A
Out=DMX512 Signal
Uin=12-24VDC
Iin=20.5A
Uout=4×(12-24)VDC
Iout=4×5A
Pout=4×(60-120)W
Temp Range:
-30~+55
FLDC4Y-DMX DMX512 & RDM Decoder
DMX IN/OUT
D+ D- D+ D-
+
+
NW
WW
NW
WW
Tunable White LED strip x 2
Uin=12-24VDC
Iin=20.5A
Uout=4×(12-24)VDC
Iout=4×5A
Pout=4×(60-120)W
Temp Range:
-30~+55
FLDC4Y-DMX DMX512 & RDM Decoder
DMX IN/OUT
D+ D- D+ D-
+
+
DMXsignal
Power Supply
12-24VDC
Constant Voltage
N
AC110-230V
NW
WW
NW
WW
Dual color LED strip x 2
DMXsignal
Each zone two channel:
zone 1 is channel 1 ~ 2,
zone 2 is channel 3 ~ 4,
zone 3 is channel 5 ~ 6,
zone 4 is channel 7 ~ 8,
channel 1,3,5,7 is WW,
channel 2,4,6,8 is CW.
DMX channel address assignment
L
N
AC85-265V
Powerinput