Sunricher SR-10 Series User manual

Instructions for SR-10XX Series& RGBY Controller
SR-10XX Series full-color LED controllers features high-reliability and
cost-effective, mainly comes in two types constant voltage series and constant current
series. There are lots of items for each type, e.g manual manipulation, wireless remote
controlling, etc. The controllers has maximium four-channel output functioning as RGBY
controller and functioning as RGB controller if only three channels output are used.
I. Parameter
1. SR-101X Constant Voltage Controller
Input voltage：12-36V
Load current: 3×5A (or 4×5A)
Max. Load Power：3×60-108W(or 4×60-108W)
Working Temperature：-20-+50℃
Load Type：0.04-0.1W LED Type
Speed Level：8 Levels
Brightness Level：8Levels
Changing mode：13 modes （9 dynamic modes，4 static modes）
Remote controlling distance：>20 meters
Dimension：L178×W45×H19mm
2. SR-101X Constant current Controller
Input voltage：12-36V
Load current: 3 or 4×350mA(700mA)

Max. Load Power：3/4×4.2-12.6（8.4-25.2）W
Work Temperature：-20-+50℃
Load Type：1W( or 3W ) LED Type
Speed Level：8 Levels
Brightness Level：8 Levels
Changing mode：13 modes（9 dynamic modes，4 static modes）
Remote controlling distance：>20 meters
Dimension：L178×W45×H19mm
II. Features:
1. 256 levels of grey scales for RGB/RGBY, full-color changing gently,
smooth, subtlely and softly without any flash,
2. 9 dynamic modes, gradient, skipping, etc. 4 static colors(R,G,B,Y)
3. To stop at a single static color(R,G,B,Y available), speed & brightness
adjustable with the function Pause
4. To work with our power repeater to expand output and drive led products
unlimitely
III. Dimension:

IV. .Directions
Standard remote controller

Mini remote controller
Three keys on main controller
No. Button Function
1 SPEED To speed up/down color changing(1-8 level cycling changing）
2 MODE Modes of color changing(9 dynamic modes,4 static modes）
3 BRIGHT To adjust the brightness（1-8 level cycling changing）
Three keys on remote controllers
NO Buttons of standard
remote controller Buttons of Mini remote controller Functions
1 A S To speed up/down color changing(1-8
level cycling changing）
2 B M Modes of color changing(9 dynamic
modes,4 static modes）
3 C B To adjust the brightness（1-8 level cycling
changing）
Besides Remote controlling is also available under the circumstance wire connecting terminal
pluging in switches on remote controller, drawing as follows:
V. Connection diagram
1.Connection diagram for single controller

2. Connection diagram for connecting power repeaters

VI．Remote controlling learning mode
To use remote controller for the first time, it must be learned by LED
controller. Methods are: hold button SPEED & MODE on LED controller
concurrently for 3 seconds, The LED indicator will turn on, then press any key
on the controller(hold it for over 2S), the indicator will give out a flash which
signifies learning mode is activated now, you can use the controller normally

from then on. Use the same method to apply on other remote controllers, one
LED controller can learn ten remote controllers(maximium).
VI. malfunctions analysis & troubleshooting
Malfunctions Causes Troubleshooting
Can not learn the remote
controller
1. learning duration (only within 3S)
exceeded 3S
2. insufficient duration of helding
remote controller
1. when indicator turns on, press any key on
remote controller ASAP
2. ensure the duration of helding remote
controller over 2S
Can not remote control 1. learning mode hasn’t activated
2. remote controlling distance is out
of range
3. insufficient duration of holding the
button
1. activate the learning mode
2. shorten the remote controlling distance
3. ensure the duration of holding the button
is over 1S
Wrong color RGB wires wrongly connected Reconnect RGB wires
LED flashing Insufficient power Replace a higher power supply