Foster 7300000 Technical specifications

Model:
7300000
EN - Induction vitroceramic hob
EN - Use and installation manual

25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 –L2 –L3
BROWN –BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 –N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645 220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645

17
EN
Dear customer!
This appliance is intended for household use only.
Materials used for packaging are nature friendly and may be recycled, deposited or
destroyed without any threats to the environment. In order to recognize these features, all
packing materials are marked with relevant symbols.
Once your appliance has become obsolete and you do not intend to use it any longer,
take adequate care not to litter the environment. Deposit your old appliance with the
authorized depot dealing with used household appliances.
Instructions for use
Instructions for use describe the appliance and the way it is handled.
These instructions are intended for various types of appliances, so you can find some
descriptions of functions that your particular appliance may not have.
These instructions are only valid for the country indicated on the appliance. If there is NO
country on the appliance, technical instructions should be observed for adapting the
appliance to comply with the requirements and regulations in your country.
Instructions for
connection
The appliance must be connected in compliance with the instructions attached to it, as
well as in compliance with relevant regulations and standards. The connection may only
be performed by a qualified person.
Rating plate
The rating plate indicating the basic information is attached on the bottom of the
appliance.
The Manufacturer strives for continuous improvements. For this reason, the text
and illustrations in this book are subject to change without notice.
Keep these instructions in a safe place and ensure that new users are familiar with
the contents. Pass them on to any future owner.
Important warnings
18
Installation
19
Connection to the power supply
20
Tecnical information
21
Operation
23
Safety functions and error display
28
Cleaning and maintenance
29
1
3
5
7
8
21
22
Technical information
Appliance introduction

18
IMPORTANT WARNINGS
xThe appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless continuously supervised.
xPrevent the children to hang around the appliance and warn them properly against the danger of burns.
xThis appliance can be used by children aged from 8 years and above, and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
xChildren shall not play with the appliance.
xCleaning and user maintenance shall not be made by children without supervision.
xUnattended cooking with fat or oil can be dangerous and may result in fire. Be sure having the preparation of
such food (fries) under constant control. Never try to extinguish a fire with water, but switch off the appliance and then
cover flame e.g. with a lid or a fire blanket.
xDanger of fire: do not store items on the cooking surfaces.
xIf the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
xDon’t use high-pressure steam cleaner or hot steam to clean the appliance.
xNever place any metal objects upon the appliance surface, such as knives, forks, spoons, pot lids, and the like, as they
may get very hot.
xThe appliance can not be activated by external timers or remote controls systems.
xDo not use the appliance for room heating.
xIf there is a wall power outlet located near the appliance and another appliance is plugged into it, make sure the power
cord does not come into contact with the hot cooking zones.
xDo not store any temperature-sensitive objects, materials, or substances underneath the appliance, e.g. detergents,
sprays, etc.
xIn case of a failure of the appliance, immediately disconnect the appliance from the power mains and contact the service
center.
xThe appliance is manufactured in compliance with the relevant effective safety standards.
xDon't connect the appliance to the power supply with an extension cable or multiple sockets, because they don't assure a
sufficient safety (e.g. overheating risk of multiple sockets).
xConnect the appliance to a permanent connection.
xInstallation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an
adequately qualified technician.
xDo not place empty pans on the appliance.
xAppliance surface should not be used as a worktop. Sharp objects may cause scratches.
xPreparing food in thin aluminum of plastic containers on the cooking zones is not allowed. Do not place any plastic
objects or aluminum foil on the appliance surface.
xAfter a prolonged use of cast iron plates, the area of the plate and the edge of the cooking zone may faded. Repair
service is not covered by the warranty.
xIf the appliance is built-in over an oven with a pyrolytic system, it should not be operated while the pyrolytic process is in
progress because it can trigger its overheating protection.
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more
detailed information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
2

23
INSTALLATION
Important warnings
•Installation of the appliance into a kitchen worktop must be performed by an adequately qualified technician.
•Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should be treated with heat
resistant glue (100°C); otherwise, the worktop finish may be discolored or deformed.
•Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall
unit or wall at one side. On the other side, however, no unit or divider should stand higher than the appliance.
NOT ALLOWED
NOT RECOMMENDED
NOT RECOMMENDED
RECOMMENDED
•The distance between the appliance edge and the adjacent tall kitchen furniture element should amount to no less than
250 mm.
•All sizes and distances to be taken for the proper functioning of the appliance are shown in figures below.
•The kitchen furniture element underneath the hob should not be fitted with a drawer. If the kitchen furniture element as a
horizontal partition wall, it should be installed no less than min 20mm from the lower surface of the appliance. The space
between the partition wall and the appliance must be empty; no objects should be placed into that gap.
•Hanging, or wall-mounted kitchen elements should be installed high enough not to interfere with the work process.
•A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker
hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available
or, if there are any flammable objects (e.g. utensil rails, wall units etc) above the appliance, a minimum safety distance
of at least 800 mm must be maintained between them and the appliance below.
•Fit the wall units and cooker hood before fitting the appliance to avoid damaging it.
•The front part must have an opening of no less than 5 mm.
•The appliance must not be installed over a fridge, fridge-freezer, freezer, dishwasher, washing machine, washer-dryer or
tumble dryer.
•Only ovens fitted with a cooling fan may be installed underneath this appliance.
•Before installing an oven, the rear wall of the kitchen furniture element should be removed in the area of the appliance
cut-out. Furthermore, a gap of at least 5 mm should be left at the front side.
a
≥ 800 mm
b
≥ 50 mm
c
≥ 20 mm
d
≥ 80 mm
e
≥ 5 mm
f
≥ 30 mm
g
≥ 250 mm
3

BUILT-IN SIZES
Installing the foam
gasket
(for glass appliances)
Before inserting the appliance into the opening in the kitchen worktop, the supplied foam
gasket must be attached to the lower side of the glass.
Do not install the appliance without the foam gasket!
The gasket should be attached to the appliance in the following way:
xRemove the protective film from the gasket.
xAttach the gasket to the lower side approximatelyA=2-3 mm from the edge. The gasket
must be attached along the entire length and should not overlap at the corners.
xWhen installing the gasket, make sure that the glass does not come into contact with any
sharp objects.
The fixing of the appliance to the worktop is achieved by using the brackets supplied in the accessory bag. After
applying the gasket and positioning the top in the recess hole, position the brackets and secure them using the screws
provided. Use the holes in the four corners of the hob.
7380645 7381645 7381245 7382645 7383645 7384645
A290
580 580 770 770 860
B
510 510 510 510 510 510
C270
560 560 750 750 840
D480
480
480
480
480
480
E55 mm 55 mm 55 mm 55 mm 55 mm 55 mm
F
6 mm 6 mm 6 mm 6 mm 6 mm 6 mm
GPP PP PP PP PP PP
HPP PP PP PP PP PP
24
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 25 of 113
DE-ACTIVATION OF THE BOOSTER
There are different options for boost function deactivation:
Select any other cooking level for the pot by slider if the booster function is currently active.
Deactivate boost function by shortcut
Deactivate boost function by activation of a pot program
Deactivation by induction system due to temperature or power management
The boost function is terminated and deactivated automatically after boost- time of 10 min. Power
level 9 is set, and sound emitted. The pot selection state is unchanged. The boost function can be
reactivated after expiration of the boost time if the temperature conditions allow it. If the pot is
removed from the cooking position whilst the boost function is active- the boost is not deactivated,
but the boost time limitation counter keeps running.
4.2.11 Pot Settings Transfer
As pots are not related to fixed cooking zones in Area Induction, they can be moved to several positions on
the cooktop. Therefore, the active power level of the pot follows the pot position. This means if a pot is
moved, the power level is automatically transferred to the new pot position.
Pot is moved by the user
The display immediately updates the pot position
The power level is transferred to the new pot position automatically
The pot is in selection mode if no other pot was selected previously
920
7300000
520
908
504
4

5
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
25
CONNECTION TO THE POWER SUPPLY

The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-
pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.

Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 –L2 –L3
BROWN –BLACK - GREY
EARTH GREEN / YELLOW
NEUTRAL
N1 –N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 –L2 –L3
BROWN –BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 –N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 –L2 –L3
BROWN –BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 –N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645
220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
1 2 3 4 5
1 2 3 4 5
7300000
5

26
WARNING! THIS APPLIANCE MUST BE GROUNDED
The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective
earthing system, which complies with current local and national safety regulations.
You can access terminal block at the bottom of the appliance. Open terminal block with the use of a screwdriver with a
slotted tip. Make electrical connection as shown in the table above, depending on the model purchased and the type of
electrical connection.
Basic adaptation of environment sensors
After each connection to electrical network, basic adaptation is automatically performed which ensures the optimal
function of the sensors. All displays light up for a few seconds. During sensor adaptation, there must be no objects. If not,
the adaptation stops until you remove the objects. During this time you cannot use the cooking panel.
1 2 3 4 5
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
6

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 34 of 113
LEAVING THE POT PROGRAMS
Pot Program can be exited
by touching the X icon
by the expiry of timeout counter
by touching the area above the pot program menu.
MELTING FUNCTION
The melting function is especially used for melting chocolate. The function sets the temperature of the
induction coil sensor to 44°C.
ACTIVATION OF THE MELTING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the chocolate icon
The melting function is activated for the selected pot
The pot is deselected
The program menu closes automatically
Note In most cases, the symbols / icons are displayed inverted for the duration of the actuation.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 37 of 113
KEEP WARM FUNCTION:
The function sets the temperature of the induction coil sensor to 70°C.
ACTIVATION OF KEEP WARM FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the keep warm icon
The keep warm function is activated for the selected pot
The pot is deselected
The program menu closes automatically
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
SYSTEM POWER SETTINGS
•The cooktop must be connected to the power supply for max. 1 minute.
•The cooktop must be switched OFF.
•Press simultaneously anywhere on the left region and on the right region in the lower half area of the display for 2 seconds.
•Values starting from 2.4kW up to 11.0 kW in 100W steps can be chosen.
•Select the power level with the selection wheel and save with the confirm button.
TECHNICAL INFORMATION
7300 000
220-240 V 1N
380-415 V 3N
50 / 60 Hz
870 x 384 mm
11000 W
179,6 Wh/kg
2600 W
3650 W
7
MODEL
SUPPLY VOLTAGE
SUPPLY FREQUENCY
COOKING AREA
TOTAL POWER
EC ELECTRIC COOKING
ENERGY CONSUMPTION
FOR THE HOB [Wh/kg]
NOMINAL POWER
BOOSTER POWER

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
APPLIANCE INTRODUCTION
ON/OFF Key Display Cooking area
At the first connection to the power supply, or after an interruption and a restoration, the
display shows the factory preset time for about 20 seconds.
First Connection
Press the ON/OFF button to turn on the appliance. When turned on, the display shows
the initial screen accompanied by an acoustic signal.
Turning the hob ON
To turn off the device, press the ON/OFF button until an acoustic signal is emitted.
The current time is displayed for about 20 seconds.
Turning the hob OFF
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 42 of 113
4.4 Functions of menu bar
4.4.1 Key lock
Key lock is a functionality intended to lock the keys during the cooktop is in operation or in pause state. This
is useful for cleaning purposes (as the touch control is unable to differentiate a wet fabric from a finger).
Precondition
Cooktop is switched ON, no pot is selected
ACTIVATION OF KEY LOCK
Touch the Key Lock icon in the menu bar
The display screen except the Key Lock icon and the ON/OFF key are locked.
8

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 25 of 113
DE-ACTIVATION OF THE BOOSTER
There are different options for boost function deactivation:
Select any other cooking level for the pot by slider if the booster function is currently active.
Deactivate boost function by shortcut
Deactivate boost function by activation of a pot program
Deactivation by induction system due to temperature or power management
The boost function is terminated and deactivated automatically after boost- time of 10 min. Power
level 9 is set, and sound emitted. The pot selection state is unchanged. The boost function can be
reactivated after expiration of the boost time if the temperature conditions allow it. If the pot is
removed from the cooking position whilst the boost function is active- the boost is not deactivated,
but the boost time limitation counter keeps running.
4.2.11 Pot Settings Transfer
As pots are not related to fixed cooking zones in Area Induction, they can be moved to several positions on
the cooktop. Therefore, the active power level of the pot follows the pot position. This means if a pot is
moved, the power level is automatically transferred to the new pot position.
Pot is moved by the user
The display immediately updates the pot position
The power level is transferred to the new pot position automatically
The pot is in selection mode if no other pot was selected previously
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
COOKWARE DETECTION
•There are no fixed cooking zones. The pot can be placed and operated anywhere inside the cooking area of the
cooktop.
•The pot is displayed according to its size and position on the cooktop in the main screen.
•There are three standard pot sizes: small, medium, big. Pots are always displayed with a round shape.
COOKWARE PLACING
•The glass ceramic surface is dimensioned to accommodate up to a maximum of 6 containers simultaneously.
•For correct pot detection and for efficient heat transmission is preferable to use circular pans of the following sizes:
•Small pots between 100-145mm in circumference won’t be detected everywhere in the cooking area.
•Oversize cookware must be placed on the back section of the cooking area only.
•Large pots might appear on the display as two different elements. Move the pot slightly or place it again on the
surface until it is recognised.
•Always keep pots a few centimeters apart.
Cookware is automatically detected when the hob is switched on.
Do not place metal objects such as knives, forks, spoons and lids on the surface of the
hob, they may become hot.
Pots should only be placed inside the cooking area, never place them too close to the display.
Min. circumference: 145 mm Max. circumference: 280 mm
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 57 of 113
ADDING FUNCTIONS TO THE MENU BAR
Precondition
Cooktop is switched ON, “Personalize” menu is opened and, at least, one function was removed from menu
bar (as described above)
Select a function outside the black box
The selected function is moved to the right-hand side of functions in the black box
Confirm the settings by selecting the tick icon or
Cancel the settings by selecting the cross icon
The user is navigated back to the settings menu
9

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
•With the appliance switched on, place a pan suitable for induction cooking on the glass ceramic surface.
The display represents the pot as a circle:
•A power setting can be selected using the bar at the bottom of the display.
•Select a level of power by tapping or sliding your finger up to the corresponding number.
•Power levels can be selected intermediate between integers, identifiable by points between one number and another.
•To stop the supply of energy and the heating of the pan, you can perform the following actions at any time:
•Dependent of the status of the pot, the pot shape is changing its color, ranging from blue to orange
, browning
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 20 of 113
There are three standard pot sizes implemented in the UI: small, medium, big. Pots are always displayed
with a round shape. Fourth pot size is only used in display conflict cases.
4.2.5 Pot Selection and Power Regulation
Precondition
The cooktop is switched on and a new pot is placed on the cooktop.
The pot is displayed in the main screen
The new pot will only be automatically selected by the system if no other pot has been selected
before
Selection mode is shown by a little animation with two function icons around the pot. Additionally, the
power level slider appears on the bottom part of the display
Select the desired power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
25
CONNECTION TO THE POWER SUPPLY
The appliance may ONLY be connected by an authorized qualified technician.
Electric system protection should comply with all relevant regulations.
The connection clips can be accessed when the connection clip covers are opened /
removed.
Before connecting the appliance, make sure the voltage indicated on the rating plate is
consistent with the voltage in your home network. Connection voltage should be checked
by a qualified technician using a corresponding measuring device!
The rating plate with basic information is attached on the lower side of the appliance.
In order to make a fixed connection to the mains, insert an all-pole circuit breaker
between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct
contact.
Before any intervention, disconnect the appliance from the power mains. Connect the
appliance in compliance with the electric connections diagram supplied; make sure the
relevant network voltage is observed!
The ground wire should be connected to the clip indicated by the earth symbol.
The mains cable should be fed through the fastening clip which protects it from being
accidentally pulled out.
After connecting the appliance, turn on all cooking zones / heaters for approximately
three minutes to make sure they are operating correctly.
Incorrect connection may destroy parts of the appliance, making the warranty void!
Connection cable on the back of the appliance should be led in such way that it DOES
NOT touch the appliance back wall, as this part will get very hot during operation.
The appliance is generally configured to the maximum available power, shown in the
technical data table. It’s possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
technician. See chapter on power limitation setting.
Installation diagram
Use cables type: H05V2V2-F
LIVE
L1 –L2 –L3
BROWN –BLACK - GREY
EARTH
GREEN / YELLOW
NEUTRAL
N1 –N2
BLUE
Model Supply Voltage / Frequency Number of phases Power cable section Connection
7380645 220-240 V~ 50/60 Hz 1 phase + N 3 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 3 x 4 mm2
380-415 V ~ 50/60 Hz 2 phases + N 4 x 2,5 mm2
220-240 V~ 50/60 Hz 1 phase + N 5 x 2,5 mm2
380-415 V ~ 50/60 Hz 3 phases + N 5 x 1,5 mm2
7381645
7381245
7382645
7383645
7384645
•Select power level 0 •Tap twice on the pot on the display •Turn the hob off
POWER LEVEL SETTING
After a few moments of inactivity, the pot is deselected and will be need to touch the circle on
display to select it again.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 57 of 113
ADDING FUNCTIONS TO THE MENU BAR
Precondition
Cooktop is switched ON, “Personalize” menu is opened and, at least, one function was removed from menu
bar (as described above)
Select a function outside the black box
The selected function is moved to the right-hand side of functions in the black box
Confirm the settings by selecting the tick icon or
Cancel the settings by selecting the cross icon
The user is navigated back to the settings menu
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
0
1-2
3-4
5-6
7-8
9
B
OFF
Slow simmer, mantining warm food
Cooking small amounts
Cooking larger quantites, roasting larger chunks
Roasting, browning
Roasting
Boiling big amounts of water (Booster)
Power
level Use
10

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
•The booster enables the induction to provide a higher power for a pot for a short period of time (10 min).
•This is useful to heat-up/boil a big amount of water
DE-ACTIVATION OF THE BOOSTER
•Select any other cooking level for the pot by slider if the booster function is currently active.
•Deactivate boost function by activation of a pot program.
•Deactivation by induction system due to temperature or power management.
•The boost function is terminated and deactivated automatically after boost - time of 10 min. Power level 9 is set, and
sound emitted.
•The boost function can be reactivated after expiration of the boost time if the temperature conditions allow it.
POT PROGRAMS
•The pot program menu contains various functions for the preparation of food.
•To enter the menu select the required pot by touching inside the pot icon.
•Select the knife and fork icon of the pot.
•The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
BOOST FUNCTION
As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
Tap to activate
B
•Pot Program can be exited:
-by touching the X icon
-by touching the area above the pot program menu
-by the expiry of timeout counter
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
11

MELTING FUNCTION
•The melting function is especially used for melting chocolate.
•The function sets the temperature of the induction coil sensor to 44°C.
KEEP WARM FUNCTION
•This function is commonly used to keep food warm.
•The function sets the temperature of the induction coil sensor to 70°C.
SIMMERING FUNCTION
•The function sets the temperature of the induction coil sensor to 94°C.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 33 of 113
4.3.2 Pot Programs
The pot program menu contains various functions for the preparation of food.
ENTERING THE POT PROGRAM MENU
Precondition
Cooktop is ON. Pot is placed on the cooktop.
Select the required pot by touching inside the pot icon
The pot gets in selection mode
Select the knife and fork icon of the pot
The pot program menu opens
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 34 of 113
LEAVING THE POT PROGRAMS
Pot Program can be exited
by touching the X icon
by the expiry of timeout counter
by touching the area above the pot program menu.
MELTING FUNCTION
The melting function is especially used for melting chocolate. The function sets the temperature of the
induction coil sensor to 44°C.
ACTIVATION OF THE MELTING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the chocolate icon
The melting function is activated for the selected pot
The pot is deselected
The program menu closes automatically
Note In most cases, the symbols / icons are displayed inverted for the duration of the actuation.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 37 of 113
KEEP WARM FUNCTION:
The function sets the temperature of the induction coil sensor to 70°C.
ACTIVATION OF KEEP WARM FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the keep warm icon
The keep warm function is activated for the selected pot
The pot is deselected
The program menu closes automatically
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 40 of 113
The simmering function is activated for the selected pot
The pot is deselected
The program menu closes automatically
DE-ACTIVATION OF SIMMERING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and simmering function is active
OPTION A
Select the pot with active simmering function
Change the power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company: 0083 / E.G.O. Germany (E.G.O. Elektro-Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 23 of 113
4.2.8 Power levels
In general, there are 18 power levels implemented in the power level slider.
[0, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9]
If a pot is selected, the display shows only full power level 0 on the slider. As soon as the user set power
level >0 a dot is displayed on the left and right side of the level to indicate half power levels.
The user can select half step power values by doing the following:
Select a half power level by touching between the power values shown in the slider
The requested power level 2.5 is set and displayed in the pot and slider
technical customer documentation
company: 0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
DEACTIVATING A POT PROGRAM
•Change the power level on the slider.
•Select the activated simmering function in the functions menu to deactivate it.
•Double tap on pot
technical customer documentation
company: 0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 82 of 113
5.4 Unsuitable Pot Material
The induction can detect pots of unsuitable pot material. In that case, the affected pot cannot be powered.
Precondition
The cooktop is switched ON. A pot of unsuitable pot material is placed on the cooktop.
The unsuitable pot is displayed in grey color with a question mark
If the user selects the pot and set a power level, the requested power level is displayed in red color
The pot cannot be heated and is still displaying power level 0 and a question mark
Select the question mark to see an info message
12

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
COOKING TIMER
•Pot timers can be used to switch OFF a pot automatically after the set time has run out.
•While the timer is running, the cooking zone can be operated normally (i.e. cooking level can be changed).
•Each pot has an independent timer. All pot timers can run in parallel.
•Select the required pot by touching inside the pot icon and select the clock icon of the pot.
•Adjust the numbers for the timer on the hours and minute wheels, then confirm the setting on the confirm icon.
•The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to the second.
•If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing.
•The cooking level is switched off.
•Confirm the timer by touching the flashing timer values or by removing the pot or by waiting 35 seconds.
CHANGING THE VALUE AND DE-ACTIVATION
•Touch the pot timer values on the pot display.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 34 of 113
LEAVING THE POT PROGRAMS
Pot Program can be exited
by touching the X icon
by the expiry of timeout counter
by touching the area above the pot program menu.
MELTING FUNCTION
The melting function is especially used for melting chocolate. The function sets the temperature of the
induction coil sensor to 44°C.
ACTIVATION OF THE MELTING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the chocolate icon
The melting function is activated for the selected pot
The pot is deselected
The program menu closes automatically
Note In most cases, the symbols / icons are displayed inverted for the duration of the actuation.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 37 of 113
KEEP WARM FUNCTION:
The function sets the temperature of the induction coil sensor to 70°C.
ACTIVATION OF KEEP WARM FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and pot program menu is opened
Select the keep warm icon
The keep warm function is activated for the selected pot
The pot is deselected
The program menu closes automatically
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 40 of 113
The simmering function is activated for the selected pot
The pot is deselected
The program menu closes automatically
DE-ACTIVATION OF SIMMERING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and simmering function is active
OPTION A
Select the pot with active simmering function
Change the power level on the slider
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
•To change the value adjust the numbers for the timer on the number wheels and confirm by touching the tick icon.
•To deactivate the timer touch the reset icon or set timer values to 00:00 and confirm by touching the tick icon.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company: 0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 83 of 113
Select the “X” icon in the top right corner to close the info message
Move the pot to a corner of the cooktop to get more coil coverage
The info box disappears 10 seconds after opening (except for the scenario conflict).
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 82 of 113
5.4 Unsuitable Pot Material
The induction can detect pots of unsuitable pot material. In that case, the affected pot cannot be powered.
Precondition
The cooktop is switched ON. A pot of unsuitable pot material is placed on the cooktop.
The unsuitable pot is displayed in grey color with a question mark
If the user selects the pot and set a power level, the requested power level is displayed in red color
The pot cannot be heated and is still displaying power level 0 and a question mark
Select the question mark to see an info message
213

MENU BAR FUNCTIONS
KEY LOCK
•Key lock is a functionality intended to lock the display while the cooktop is in operation.
•This is useful for cleaning purposes.
•To activate touch the Key Lock icon in the menu bar.
•The display screen except the Key Lock icon and the ON/OFF key are locked.
•To de-activate this function touch the Key Lock icon for 3 seconds.
STAND ALONE TIMER
•Stand-alone timer has the performance of an egg timer.
•It can be adjusted within a range of 1 min to 9 h 59 min.
•After the adjusted time has run out, a signal tone is emitted.
•Stand-alone timer has no impact on any cooking zone.
•To activate this function touch the Hoursglass icon in the menu bar.
•Adjust the numbers for the timer on the hours and minute wheels.
•Confirm the setting with the tick icon.
•If the timer expires a signal tone is emitted and the timer numbers are highlighted and flashing.
•Confirm the timer by touching the flashing timer values.
•The signal tone stops, and the hourglass icon is displayed again.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 22 of 113
4.2.6 Shortcut switch OFF pot
To be able to switch off a pot really fast the user can double tab on the required pot. The power level is
immediately switched to power level 0.
Double tap on pot icon
Pot is selected and is then switched OFF.
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
Generally, two selection modes are possible:
Direct Selection:
The selection is done by touching directly on the desired cooking level number.
Sliding:
The selection is done by wiping with the finger from the left side to the right or vice versa.
The power level slider is visible if a pot is in selection mode.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 42 of 113
4.4 Functions of menu bar
4.4.1 Key lock
Key lock is a functionality intended to lock the keys during the cooktop is in operation or in pause state. This
is useful for cleaning purposes (as the touch control is unable to differentiate a wet fabric from a finger).
Precondition
Cooktop is switched ON, no pot is selected
ACTIVATION OF KEY LOCK
Touch the Key Lock icon in the menu bar
The display screen except the Key Lock icon and the ON/OFF key are locked.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 45 of 113
Confirm the setting with the tick icon
The stand-alone timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired a signal tone is emitted and the timer numbers are highlighted and flashing
Confirm the timer by touching the flashing timer values
The signal tone stops, and the hourglass icon is displayed again
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 83 of 113
Select the “X” icon in the top right corner to close the info message
Move the pot to a corner of the cooktop to get more coil coverage
The info box disappears 10 seconds after opening (except for the scenario conflict).
14

PAUSE
•Pause function is a feature to “freeze” the cooktop for max. 10 minutes.
•No cooking zone will provide any power.
•All timers (including stand-alone timer) will be paused.
•To activate the pause function touch the pause icon in the menu bar.
•All system states are maintained throughout the pause.
•Any timer set before and stopped during the pause, continues when the pause mode is finished
•If pause state lasts longer than 10 min, the cooktop will turn OFF.
•Booster will be canceled when activating Pause function. The power level will be set to level 9 by the system after
deactivation of Pause.
•To exit the Pause function press the play button in the center of the screen.
SETTINGS MENU
•The settings menu is integrated in the bottom bar of the main screen.
•To access the menu touch the menu icon in the bottom right corner.
•It contains various functions to configurate the cooktop:
-Personalise
-Child lock
-Sound
-Brightness
-Clock
-Language
-Factory reset
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 51 of 113
Pause function is active
DE-ACTIVATION OF PAUSE FUNCTION
Touch the continue icon
The pause function is terminated, and the cooktop will continue with all actions set before.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 57 of 113
ADDING FUNCTIONS TO THE MENU BAR
Precondition
Cooktop is switched ON, “Personalize” menu is opened and, at least, one function was removed from menu
bar (as described above)
Select a function outside the black box
The selected function is moved to the right-hand side of functions in the black box
Confirm the settings by selecting the tick icon or
Cancel the settings by selecting the cross icon
The user is navigated back to the settings menu
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
technical customer documentation
company: 0083 / E.G.O. Germany (E.G.O. Elektro-Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
15

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 24 of 113
4.2.9 Power level display
Dependent of the status of the pot, the pot shape is changing its color.
Power level 0: Pot is displayed in blue
Power level 1 to 3.5: Pot is displayed in purple
Pot Programs: Pot is displayed in purple
Power level 4 to 6.5: Pot is displayed in red
Power level 7 to B: Pot is displayed in orange
Lifted pot: Pot is displayed in grey
4.2.10 Boost function
The booster enables the induction to provide a higher power for a pot than its nominal power for a short
period of time (10 min for Area induction). This is useful to heat-up/boil a big amount of water.
Note As the booster function may reach high temperatures, it must only be used for cooking
processes using water. Oil or fat may start to burn if booster is used.
ACTIVATION OF THE BOOSTER
Precondition
Cooktop is switched ON. Pot is placed on the cooktop and pot is in selection mode.
Select booster level on the slider (e.g., shown as “B” or “P”)
The booster for the selected cooking zone is activated. The display for the pot shows a boost sign.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 51 of 113
Pause function is active
DE-ACTIVATION OF PAUSE FUNCTION
Touch the continue icon
The pause function is terminated, and the cooktop will continue with all actions set before.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 18 of 113
4.2.2 Switching ON and OFF
Precondition
The cooktop is in standby mode, i. e., it is connected to the power supply voltage and the self-test has been
performed successfully.
Touch the ON/OFF SmartKii.
The cooktop is turned on.
No logo is implemented in the E.G.O. standard variant. A customer brand logo can be displayed optionally.
Main screen for cooking is displayed
Touch the ON/OFF SmartKii.
The cooktop will go to standby mode. A running stand-alone timer will continue with its count down;
the residual heat indication is displayed. The real time clock is displayed for additional 15 seconds.
ON/OFF activities are accentuated by corresponding acoustic signals.
The cooktop switches OFF automatically after 20 s if all cooking levels are set to 0 and no operation is
performed by the user. A running egg timer will continue with its count down; the residual heat will also be
indicated.
Note For safety reasons, switching OFF the cooktop by the ON/OFF SmartKii is always possible.
PERSONALISE
•Functions which are displayed in the menu bar in the main screen can be personalised.
•Select the Personalize icon in the settings menu.
•The black box shows the function which are displayed in the menu bar of the main screen.
•Select a function in the box to remove a function or to change the position.
•Any function can be added back selecting it from outside the box.
•Operation is confirmed by selecting the tick icon in the bottom left corner.
CHILD LOCK
•Child lock is a functionality to protect the cooktop against unintended operation.
•If locked, the cooktop may be turned ON, but the main screen for operating the cooktop is not displayed.
•Child lock stays active even if the power supply is interrupted and recovered. It must be de-activated manually.
•To activate select the child lock icon in the settings menu and select “ON”.
•Select the confirm icon to confirm the settings.
•An info message occurs explaining that child lock gets valid after the next switch ON.
•Every time you switch on the hob, the display shows the child safety lock symbol first.
•Touch the symbol for three seconds, then the main screen shows on the display.
•To de-activate select the child lock icon in the settings menu and select “OFF”.
SOUND
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 57 of 113
ADDING FUNCTIONS TO THE MENU BAR
Precondition
Cooktop is switched ON, “Personalize” menu is opened and, at least, one function was removed from menu
bar (as described above)
Select a function outside the black box
The selected function is moved to the right-hand side of functions in the black box
Confirm the settings by selecting the tick icon or
Cancel the settings by selecting the cross icon
The user is navigated back to the settings menu
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 56 of 113
The selected function will be removed
Select the confirm icon to store the setting
The „Personalize“ submenu is closed
Back on main screen the user can see the change of the functions in the menu bar
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
•Sound is adjustable on 6 different levels.
•There are two volume sliders available: notification and timer.
•To costumize sound select the sound icon in the settings.
•Slide to the desired volume level on the slider.
•Confirm the settings by selecting the confirm icon.
Errors will always sound in maximum
volume independent from the settings in
the sound menu.
16

technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 56 of 113
The selected function will be removed
Select the confirm icon to store the setting
The „Personalize“ submenu is closed
Back on main screen the user can see the change of the functions in the menu bar
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 55 of 113
4.4.5 Personalize
The user can personalize the functions which are displayed the menu bar in the main screen, except the
settings menu. Functions can be removed from the menu bar or the position can be changed.
REMOVING FUNCTIONS FROM MENU BAR
Precondition
Cooktop is switched ON, settings menu is opened
Select the Personalize icon in the settings menu
The Personalize submenu opens
The black box shows the function which are displayed in the menu bar of the main screen
Select a function in the box to remove a function or to change the position
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 59 of 113
The Child lock submenu opens
Child lock is deactivated per default
Select “ON” in the wheel
Select the confirm icon to confirm the settings
The Child lock is activated, and the Child lock menu is closed
An info message occurs explaining the user that child lock gets valid after the next switch ON
Brightness
•Brightness level can be modified to improve visibility.
•Select the brightness icon in the settings menu.
•Adjust the brightness on the slider.
•Confirm the settings by selecting the tick icon.
Clock
•In the clock settings menu, the timecan be adjusted. The clock uses 24 h time format by default.
•Select the clock icon in the settings menu.
•Adjust the clock on the hours and minute wheels, if required change to 12 hours’ time format.
•Confirm the settings by selecting the tick icon.
Change of language
•In the language settings it’s possible to change the sistem languange to any of the following: English, German,
French, Spanish, Italian, Chinese (simplified), Korean, Vietnamese.
•In the settings menu slide the settings functions from right hand side to left hand side to get the function fully visible.
•Select the globe icon to enter the language submenu.
•Select the desired language on the wheel and confirm the settings by selecting the tick icon.
Factory reset
•Settings can be reset to factory conditisions.
•In the settings menu slide the settings functions from right hand side to left hand side to get the function fully visible.
•Select the factory icon to enter the factory reset function.
•Confirm the reset by selecting the tick icon.
17

PROTECTION AND SAFETY WARNINGS
COOKING TIME LIMITER
•The cooking time limiter is an additional safety feature to turn OFF pots after a certain time.
RESIDUAL HEAT INDICATOR
•Residual Heat Indication is a safety feature to indicate that parts of the surface of the glass ceramic still keep a
temperature which may cause burns when touching.
•The display shows the affected area of the surface with an H.
technical customer documentation
company:
0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 40 of 113
The simmering function is activated for the selected pot
The pot is deselected
The program menu closes automatically
DE-ACTIVATION OF SIMMERING FUNCTION
Precondition
Cooktop is ON. Pot is placed on the cooktop and simmering function is active
OPTION A
Select the pot with active simmering function
Change the power level on the slider
technical customer documentation
company: 0083 / E.G.O. Germany (E.G.O. Elektro-Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 28 of 113
Confirm the setting on the confirm icon
The pot timer menu is left
The timer starts counting backwards. Beneath 1 hour, the display shows the current time accurate to
the second.
If the timer expired, a signal tone will be emitted, and the timer numbers are highlighted and flashing
The cooking level is switched off
Confirm the timer by touching the flashing timer values or by removing the pot
The signal tone stops, and the clock icon is displayed on the pot again
technical customer documentation
company: 0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 26 of 113
4.2.12 Pot Lifting
If a pot is lifted by the user, the induction keeps the pot information for approx. 20 seconds. During that time
the user can replace the pot and all pot settings are reset automatically.
Lift pot
Pot is displayed as lifted. Pot information remains in the display for approx. 20 seconds
Active pot timer is paused
Replace pot on the cooktop
All pot settings are reset automatically
Notes If the pot is not replaced on the cooktop within 20 seconds, the pot display is removed.
If a new pot is placed in area of a lifted pot, this pot is deleted.
technical customer documentation
company: 0083
/
E.G.O. Germany (E.G.O. Elektro
-
Gerätebau GmbH)
document id.: 90.60113.039-001-08-A / state: 120 - at review
designation: Lumio customer documentation page 82 of 113
5.4 Unsuitable Pot Material
The induction can detect pots of unsuitable pot material. In that case, the affected pot cannot be powered.
Precondition
The cooktop is switched ON. A pot of unsuitable pot material is placed on the cooktop.
The unsuitable pot is displayed in grey color with a question mark
If the user selects the pot and set a power level, the requested power level is displayed in red color
The pot cannot be heated and is still displaying power level 0 and a question mark
Select the question mark to see an info message
COOKING LEVEL
Melting
Keep warm
Simmering
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
P
2 h
2 h
2 h
10 h
10 h
5 h
5 h
5 h
5 h
4 h
4 h
3 h
3 h
2 h
2 h
2 h
2 h
2 h
2 h
1 h
10 min
MAX. OPERATION TIME
As long as the residual heat indicators are on, don’t touch the heating zones and don’t put any
heat sensitive object on them.
APPROPRIATE COOKWARE
•In pan selection mode, a pan that is not appropriate shows in a grey color with a question mark.
•Touch the question mark to show the info message.
18