Foster Abstract User manual

Foster spa
via M.S. Ottone, 18/20
42041 Brescello (RE) - Italy
tel. [phone] - tel. Servizio Assistenza +39.0522.684450
fax [phone] - fax Servizio Ricambi +39.0522.962166
e-mail: [email protected]
www.fosterspa.com
USER'S MANUAL FOR GAS COOKER HOBS
Abstract
cod. 9606801

20
ENGLISH
Table of Contents
1. Usage warnings ................................................................................................................... 21
2. Safety warnings.................................................................................................................... 22
3. Warnings for disposal.......................................................................................................... 22
4. Know your appliance............................................................................................................ 23
GENERAL WARNINGS
General recommendation to be consulted before installation
and use of the purchased cooker hob.
INSTALLER INSTRUCTIONS
They are intended for the qualified technician that will complete
appliance installation, commissioning and initial testing.
USER INSTRUCTIONS
The indicate usage recommendations, a description of controls and the
correct cleaning and maintenance operations for the appliance.
5. First installation................................................................................................................... 24
6. Positioning in the work top.................................................................................................. 24
7. Fastening the cooker hob to the cabinet............................................................................... 26
8. Connecting the cooker hob to the gas network..................................................................... 29
9. Room ventilation.................................................................................................................. 30
10. Discharging combustion products (exhaust)........................................................................ 31
11. Adapting to different types of gasses.................................................................................... 31
12. Adjustment of the minimum................................................................................................. 33
13. Electrical connection of the cooker hob................................................................................ 33
14. Cooker hob use.................................................................................................................... 34
15. Cleaning and maintenance................................................................................................... 37
Gas cooker hobs summary........................................................................................................... 182
Dear Customer,
We thank you for having chosen a Foster cooker hob.
Your preference is our pride and satisfaction.
In this document are the recommendations and instructions that will enable you to make the best
use of the purchased cooker hob and guarantee its best preservation in time. We ask that you take a
few minutes to protect the efficiency of the product and for your satisfaction.
With kind regards
Foster spa

21
ENGLISH
GENERAL WARNINGS
1. Usage warnings
This manual is and integral part of this appliance. It is necessary to keep it undamaged
and on hand for the entire life cycle of the hob. We recommend carefully reading
this document and all instructions contained within before using the appliance.
Installation must be completed by qualified personnel according to current
standards. This appliance is intended for domestic type use, and is conform with
CE Directives currently in force.
The appliance has been manufactured to carry out the following function: COOK-
ING AND HEATING FOOD, ANY OTHER USE MUST BE CONSIDERED IM-
PROPER.
The manufacturer declines any responsibility for uses that are different from those
indicated.
• Never use this appliance for heating environments.
• Do not leave packaging material waste unguarded in the household environment.
• Separate the various packaging waste materials and deliver them to the closest
selective waste collection centres.
This appliance has a mark pursuant to European Directive 2002/96/EC with regard
to waste, electric and electronic appliances (waste electrical and electronic equip-
ment - WEEE). This Directive defines the Standards for the collection and recycling of
dismissed appliances valid throughout the territory of the European Union.
The identification plate, with techni-
cal data, serial number and marking, is
positioned in view under the hous-
ing [Fig. 1].
THE PLATE MUST NEVER BE RE-
MOVED. Fig. 1:
position of the identification plate

22
ENGLISH
GENERAL WARNINGS
2. Safety warnings
In your interest and for your safety, by law it has been established that instal-
lation and service for all electric or gas appliances must be carried out
by qualified personnel, according to current regulations and the require-
ments of local companies supplying gas and electric power.
• Gas or electric appliances must always be disengaged by competent persons.
• The plug to be connected to the power supply cable and the related socket must
be of the same kind and conform to regulations in force.
• The socket must be accessible once the appliance is installed.
• Never detach the plug by pulling on the cord.
• It is mandatory to have an earth connection as per modes foreseen in the electrical
system safety standards.
• Do not block the openings and ventilation and heat dispersion slots.
Immediately after installation complete a short test on the appliance following the
instructions contained in subsequent pages in this manual. If it does not operate
correctly, disconnect the appliance from the power mains and contact
the closest technical assistance centre: NEVER ATTEMPT TO REPAIR THE
APPLIANCE.
During use the appliance becomes very hot. The use of proper thermal gloves is rec-
ommended for any type of operation. The appliance is to be used by adult persons.
DO NOT ALLOW CHILDREN TO COME CLOSE OR PLAY WITH IT.
The manufacturer declines any liability for damages to persons or property, caused by
the non observance of the following regulations or resulting from tampering with even
a single part of the appliance and using non original spare parts.
3. Warnings for disposal
OUR CARE FOR THE ENVIRONMENT
Our products are packaged using non polluting materials, that are therefore compatible with the en-
vironment and recyclable. We request your cooperation in making sure that packaging materials are
disposed of correctly. Contact your reseller or competent organizations in your area for information
about waste collection centres, recycling and disposal.

23
ENGLISH
GENERAL WARNINGS
DO NOT ABBANDON THE PACKAGING MATERIAL OR PARTS OF IT. THEY
MAY CREATE A SUFFOCATION DANGER FOR CHILDREN, ESPECIALLY
PLASTIC BAGS.
Even your old appliance must be disposed of properly, this will contribute to avoiding negative envi-
ronmental and health consequences, that would occur as a result of improper disposal.
IMPORTANT: this appliance cannot be treated as household waste. Deliver the old
appliance to the local company that is authorised to collect appliances that are no
longer in use. A proper disposal makes an intelligent recovery of precious materials. It
is also necessary to cut the cable connecting to the power mains and remove it along
with the plug.
4. Know your appliance
All drawings relating to the Foster cooker hobs manufactured today, are at the end of this manual, Gas
cooker hobs summary [Page 182].
We ask that you recognise the drawing of the cooker hob you have purchased to familiarise with the
main technical-functional features.
For research practicality the cooker hobs are distinguished in two macro-families:
• Traditional built-in cooker hobs: “8 mm edge”, “Q4 edge” and “semi-flush edge”;
• Flush built-in cooker hobs: “flush-mount” edge.
Regardless of the type of edge, the first group has a simple traditional built-in hole. The cooker
hobs with "flush-mount" edge have a more detailed drawing to enable realisation of the "made to
measure" hole, or having a step necessary to house the edge of the cooker hub so it is "flush" with
the worktop.
Numbers in correspondence with the burners are present in all drawings. Such numbers identify the
type of burner depending on the key below. To know the powers of the burners of the gas cooker hub
you purchased, refer to reading the powers table depending on the type of gas used [Page 182].

24
ENGLISH
INSTALLER INSTRUCTIONS
ENGLISH
5. First installation
Do not leave packaging material waste unguarded in the household environment.
Separate the various packaging waste materials and deliver them to the
closest selective waste collection centres.
In order to remove all manufacturing residues, we recommend cleaning the appliance.
For further information on cleaning see Chapter 15 [Page 37].
6. Positioning in the work top
The following interventions require masonry and/or carpentry work and must there-
fore be completed by a competent technician. Installation can be completed on dif-
ferent materials, such as masonry, metal, solid wood and plastic laminated wood, as
long as it is heat resistant (T 100°C).
6.1 Installation on the support structure (worktop) of a traditional built-in
cooker hob (8 mm edge, Q4 edge, semi-flush edge)
Cut an opening on the top surface of the
cabinet with the dimensions and position
indicated here below and represented in
the drawing [Fig. 2].
The dimensions of the built-in hole are
shown in the Gas cooker hobs sum-
mary - models with traditional built-
in [Page 182], in correspondence of the
drawing of the purchased cooker hob.
A
B
Fig. 2: cutting the hole for the built-in

25
ENGLISH
INSTALLER INSTRUCTIONS
• The distance of the cooker hob
from the back edge must be at least
50mm;
• The distance of the cooker hob from
the walls that exceed worktop height
must be at least 100 mm;
• Make sure that there is a minimum
distance of 750 mm from the burner
to any shelf placed vertically above it;
50
750
100
Fig. 3: cooker hob distances
• Make sure that any exhaust appliances installed above the cooker hob are posi-
tioned according to the measurements indicated in the hood instructions booklet.
• Carefully position the supplied in-
sulating gasket along the external
perimeter of the hole created on the
worktop, trying to make it adhere
along the entire surface by slightly
pressing it by hand [Fig. 4].
• Once these operations have been
completed, use the supplied brack-
ets to fasten the hob to the structure.
Refer to the “Fastening the cook-
er hob to the cabinet” paragraph
[Page 26]. Fig. 4:
positioning the insulating gasket
6.2 Installation on the support structure (worktop) of a flush built-in cooker
hob (flush-mount edge)
This type of appliance requires milling on the 1.5 mm deep worktop,
which measurements are indicated in the top drawing, identifiable in the section
Gas cooker hobs summary - models with "flush" built-in [Page 182].
The step is necessary to house the cooker hub edge so that it is "flush" with the
worktop.

26
ENGLISH
INSTALLER INSTRUCTIONS
• Accurately clean milling.
• Before positioning the top, lay the
sealer gasket provided on the entire
milling surface [Fig. 5].
• Once these operations have been
completed, use the supplied brackets
to fasten the hob to the structure. Re-
fer to the “Fastening the cooker
hob to the cabinet” paragraph
[Page 26].
Fig. 5: positioning the insulating gasket
A constant light of at least 0.5 mm is envisioned between the external dimensions of the
stainlesssteelplatformandtheinternaldimensionsoftheloweringthatmustberespected
during assembly. The temperatures that develop during use of the cooker hub induce a
slight elongation on the stainless steel platform, therefore, the envisioned light enables
avoidinganyinterferences.Withregardtothekitchenworktop,thetemperaturesinduced
by the cooker hub - whether in the section and on the contact top - are very contained.
We recommend assembling the cooker hubs with flush-mount edge on water-repel-
lent materials.
7. Fastening the cooker hob to the cabinet
Fasten the supplied hooks to the brackets under the appliance, as shown here below.
The supplied hooks make it possible to fasten to a top whose thickness is between
30 and 40 mm.
IMPORTANT:
• For fastening this product to the support structure, the use of mechanical or
electric screwdrivers is not recommended and only moderate pressure
must be exerted by hands to the clamping parts.
• The surface under the appliance must be at at least 5 mm from the bottom of it
and must have an opening for passing gas and electric conduit that is
at least 50x50 mm.
• If this product is installed above an oven, it must be equipped with a
cooling fan.

27
ENGLISH
INSTALLER INSTRUCTIONS
7.1 Fixed hooks
They make it possible to fasten the cooker hob using fixing frames pre-set along specific points.
Standard edge (8 mm)
Q4 edge (4 mm)
Semi-flush edge (3 mm)
Flush-mount edge

28
ENGLISH
INSTALLER INSTRUCTIONS
Set hook B in frame A welded to the hob,
making sure that it is blocked in the spe-
cific holes based on top thickness (for a
30 mm thick top, lock the hook in the the
highest hole in the frame; for a 40 mm thick
top, block the hook in the lowest hole of the
frame).
Rotate tongue CA until it is positioned
above the top, then tighten screw D.
B A
CD
30
B A
CD
40
7.2 Sliding hooks
Make it possible to fasten the cooker hob without pre-set fastening points.
Standard edge (8 mm)
ABC
Flush-mount edge - Q4 (only for S4000 series)
A B C
Insert hook B in the sliding guide CA.
Manually lock the hook using screw A.

29
ENGLISH
INSTALLER INSTRUCTIONS
7.3 Fixed brackets
Make it possible to fasten the cooker hob in pre-set fastening points.
Standard edge (8 mm)
A
B
Introduce the bracket B in appropriate top seat.
Manually lock the bracket using screw A.
8. Connecting the cooker hob to the gas network
It is necessary for the gas supply system to conform to local regulations in force.
It is necessary to verify that local distribution conditions (gas nature and pressure)
and the appliance adjustment status are compatible.
IMPORTANT: If the appliance is installed above an oven, it is necessary to avoid
passing the gas tube behind the oven in order to avoid overheating.
The connection to the gas sup-
ply network can be completed us-
ing rigid copper piping or with a
continuous flexible steel pipe
on the wall, according to established
regulations that are parts of the regu-
lations in force [Fig. 6]. In any case
every pipe connected to the
gas supply network must be
equipped with a safety intercep-
tion valve.
stainless steel
flexible pipe
cooker hob
fitting
gasket
copper
rigid pipe
Fig. 6:
connection to the gas supply network

30
ENGLISH
INSTALLER INSTRUCTIONS
IMPORTANT: Always place the gasket between the hob fitting and the connection
pipe.
• If using a stainless steel flexible pipe, it must be installed so that it does not
come in contact with any part of the cabinet, but passes through an unoccupied
area where its entire length can be inspected. Maximum extension of the flexible
pipe must be less than 2 metres.
• The gas fitting is the type with a 1/2” gas ISO R7 tapered thread.
After connecting the appliance to the gas supply network always verify fittings
seal using a soapy solution.
VERIFYING THE SEAL USING NAKED FLAMES IS ABSOLUTELY PROHIBITED.
The cooker hob is tested for methane gas G20 (2H) at a pressure of
20mbar. For supplying with other types of gas, see the Adapting to the different
types of gas table [Page 31]
8.1 Connection to liquid gas
Use a pressure regulator and realise connection on cylinder in compliance with the
prescriptions established by the current Standards.
Ensure the supply pressure respects the values indicated in the table
Adapting to different types of gasses [Page 31]. In this case also, connection
must be carried out with copper rigid pipe or with stainless steel flexible pipe with
continuous wall.
9. Room ventilation
IMPORTANT: The appliance can only be installed in rooms that are permanently
ventilated, as required by standards in force.

31
ENGLISH
INSTALLER INSTRUCTIONS
10. Discharging combustion products
(exhaust)
Discharge of combustion products must be ensured through hoods connected to an
efficient natural draught flue, or through a forced exhaust.
An efficient exhaust system requires an accurate design by a specialist that is ap-
proved for this work, following positions and distances contained in regulations.
IMPORTANT: At the end of the intervention the installer must issue a conformity
certificate.
11. Adapting to different types of gasses
Gas
type
Burner Rated
capacity
(KW)
Rated con-
sumption
(g/h)
Injector
(ø mm)
Min
rated capacity
(KW)
Series No. Ref.
LPG GAS
G30/G31 28÷30/37 mbar
II
2 Auxiliary 1,00 73 0,50 0,52
3 Semi-quick 1,75 127 0,65 0,52
4 Quick 2,70 196 0,80 0,90
5 Triple crown 3,50 254 0,95 1,80
10 Dual 4,50 328 i 0.46 / and 0.66 i 0.46 / and 0.66
III
6 Auxiliary 1,10 80 0,52 0,52
7 Semi-quick 1,75 127 0,65 0,52
8 Quick 3,00 218 0,85 0,90
9 Triple crown 3,80 276 0,98 1,80
AE
11 Auxiliary 1,00 73 0,50 0,52
12 Semi-quick 1,75 127 0,65 0,52
13 Quick 3,00 218 0,85 0,90
14 Dual gear 5,00 364 i 0.46 / and 0.95 i 0.30 / and 1.40
INSTALLER INSTRUCTIONS

32
ENGLISH
INSTALLER INSTRUCTIONS
Gas
type
Burner Rated
capacity
(KW)
Rated con-
sumption
(l/h)
Injector
(ø mm)
Min
rated capacity
(KW)
Series No. Ref.
METHANE GAS
G20 20 mbar
II
2 Auxiliary 1,00 95 0,72 0,52
3 Semi-quick 1,75 167 0,97 0,52
4 Quick 2,70 257 1,08 0,90
5 Triple crown 3,50 333 1,35 1,80
10 Dual 4,50 429 i 0.72 / and 1.02 i 0.46 / and 0.66
III
6 Auxiliary 1,10 105 0,73 0,52
7 Semi-quick 1,75 167 0,98 0,52
8 Quick 3,00 285 1,26 0,90
9 Triple crown 3,80 362 1,35 1,80
AE
11 Auxiliary 1,00 95 0,72 0,52
12 Semi-quick 1,75 167 0,97 0,52
13 Quick 3,00 285 1,32 0,90
14 Dual gear 5,00 476 i 0.75 / and 1.58 i 0.30 / and 1.40
The appliance is tested for methane gas G20 (2H) at a pressure of 20 mbar. When
using with other types of gas it is necessary to replace the burner nozzles, and adjust
the minimum flame on the gas taps. For nozzle replacement, proceed as described in
the following paragraphs.
11.1 Cooker hob nozzle replacement
IMPORTANT: Before completing the following operations, always make sure that the
appliance is disconnected from the power mains.
1. Remove the grids, remove all flame spreading
caps and crowns.
2. Using a 7 mm tube spanner, unscrew the burner
nozzles [Fig.7].
3. Proceed with burner nozzle replacement based on
the type of gas to be used (table “Adapting to
different types of gasses” [Page 31]).
4. Correctly reposition the burner in its seat.
Fig. 7: nozzle replacement

33
ENGLISH
INSTALLER INSTRUCTIONS
IMPORTANT: After adjusting for use with a gas that is different from the initial testing
one, replace the label on appliance housing with the one that corresponds to the new
gas type.
12. Adjustment of the minimum
Instructions for urban and methane gas
1. Light the burner and bring it to the minimum
position.
2. Remove the gas tap knob and turn the adjust-
ment screw [Fig. 8] inside or on the side of the
tap rod (depending on the model), until a regular
minimum flame is obtained.
3. Re-assemble the knob and verify burner flame
stability (when quickly rotating the hand from
maximum to minimum position the flame must
not shut off).
4. Repeat the operation on all gas taps.
Fig. 8: adjustment of the minimum
Instructions for liquid gas (LPG)
Tighten the screw inside, or on the side of the tap (depending on the mode), rod
clockwise completely.
13. Electrical connection of the cooker hob
IMPORTANT: Before completing the following operation, always make sure that the
voltage and sizing of the power supply line correspond to the characteristics indicated
on the place located under the housing of the appliance. This plate must never be
removed.

34
ENGLISH
USER INSTRUCTIONS
It is mandatory to have an earth connection as per modes foreseen in the electrical
system safety standards.
• If using a fixed connection, it is necessary to pre-set an omnipolar interruption
device on the appliance power supply line with a contacts distance that is equal
to or greater than 3 mm, located in a position that can be reached easily and is in
proximity of the appliance.
• If using a connection with a plug and socket, verify that they are of the same type.
Avoid using reducers, adaptors or diverters because they may cause
overheating or burns.
IMPORTANT: The manufacturer declines any liability for damages to persons or
property, caused by the non observance of the following regulations or resulting from
tampering with even a single part of the appliance.
14. Cooker hob use
14.1 Lighting the burners
Before lighting hob burners, make sure
that the flame spreading crowns are po-
sitioned in their seat with the respective
caps.
parallel and centred tilted
not centred
tilted
Fig. 9:
crown position
The new burners called "Series III" are assem-
bled on certain cooker hobs. The lock system
between cover (B) and flame spreading (A)
guarantees perfect positioning and large
cleaning ability.
Fig. 10: positioning of the series III burner

35
ENGLISH
USER INSTRUCTIONS
The upper cover (B) of the burners must be placed in opposite seat with the two intro-
ductions notches in correspondence of the two cylinders below (C) and tighten clock-
wise.
The associated burner is indicated near each knob.
The appliance is equipped with an electric ignition
device. It is sufficient to press the knob and rotate it
anti-clockwise to the maximum flame symbol, until
it is lit. If it does not ignite within the first 15sec-
onds, bring the knob on [chiuso] (closed)
and do not try to re-ignite for 60 seconds.
Once it is lit, keep the knob pressed for a few sec-
onds in order for thermocouple to heat up. It is
possible that the burner shuts off when the knob
is released: this means that the thermocouple was
not sufficiently heated. Wait a few seconds and re-
peat the operation, keeping the knob pressed for a
little longer. Once the burner is lit, it is possible to
adjust the flame based on need.
OFF
MAX
MIN
Fig. 11: standard burner knob
CHIUSO
MAX 1
MAX 2
MAX 1
MIN 2 MAX 1
CHIUSO 2
MIN 1
CHIUSO 2
Fig. 12: burner knob
dual (S4000)/dual gear
CHIUSO
1 MAX
2 CHIUSO
1 MIN
2 CHIUSO
1 MAX
2 MAX
1 MIN
2 MIN
Fig. 13: burner knob
dual (GIOTTO/VULCANO)
After every use of the hob, always verify that the
control knobs are in [chiuso] (closed) posi-
tion.
If the burners were to shut off accidentally, after
about 20 seconds a safety device intervenes and
blocks gas output, even when the tap is open. In
this case bring the knob to [chiuso] (closed)
position and do not try to light the burner for at
least 60seconds.
USER INSTRUCTIONS
1 INSIDE BURNER
2 EXTERNAL CROWNS
1 INSIDE BURNER
2 EXTERNAL CROWNS

36
ENGLISH
USER INSTRUCTIONS
14.2 Practical recommendations for burner use
For better burner yield, and minimum
gas consumption, it is necessary to use
flat and regular bottom pots, equipped
with a cover and proportioned to the
burner, in order to avoid that the flame
goes up their sides (see the “Pots
diameter” paragraph [Page 36]).
When boiling, reduce the flame as much
as needed to make sure that the liquid
does not overflow. Fig. 14:
pots use
During cooking, all containers or steak pans, also to avoid burns or damage to the
hob, must not exceed the measurements indicated in the paragraph “Pot diameter”
[Page 36]). Do not heat empty pots or pans, because they may overheat.
When using greases or oils, pay careful attention because, when overheating, they
may catch on fire. If a pan containing greases or oil catches on fire, do not pour water
on it because it may cause burns; extinguish the fire by covering the pan with a wet
cloth and disconnect the appliance from the power mains.
14.3 Pot diameter
• Auxiliary burner: from 6 to 14 cm
• Semi-quick burner: from 15 to 20 cm
• Quick burner: from 21 to 26 cm
• Double crown, triple crown, dual burners: from 24 to 28 cm
During operation, the cooker hob generates heat and humidity in the room it is in-
stalled in. Make sure that the kitchen is well ventilated. A prolonged used of the ap-
pliance with some or all burners may require additional ventilation such as opening a
window and/or a greater suction power from the exhaust hood.

37
ENGLISH
USER INSTRUCTIONS
15. Cleaning and maintenance
Do not use a steam jet to clean the appliance.
Before any intervention it is necessary to disengage the appliance power supply.
Avoid leaving acid or alkaline (vinegar, lemon juice, salt, tomato juice,...) substances
on the steel, grids and other parts of the appliance.
15.1 Cleaning the stainless steel
In order to properly preserve the stainless steel, it is necessary to regularly clean it after each use,
once it has cooled down.
15.1.1 Daily ordinary cleaning
In order to clean and preserve stainless steel surfaces, only use specific products that do not contain
abrasives or chlorine based acid substances.
Usage mode: pour the product on a wet cloth and pass it over the surface, carefully rinse and dry using
a soft cloth or a deerskin.
15.1.2 Food stains or residue
Absolutely avoid using metal sponges and sharp scrapers to avoid damaging the sur-
faces. Use normal products for steel, non abrasives, using wood or plastic material
tools if needed. Carefully rinse and dry using a soft cloth or a deerskin.
We recommend using Foster Steel Clean to clean the steel; for information on where it
can be obtained, contact the after-sales technical assistance centre.
Do not use chemical detergents such as oven sprays or stain removers.
15.2 Cleaning gas components
The grids, caps and flame spreading crowns are removable in order to simplify cleaning: wash then
in hot water with non abrasive detergent, making sure that any crud is removed and dry them imme-
diately using a cloth. Re-assemble the caps on their crowns. The cast iron components, like the grids
and the burners, must never be washed in dishwashers.
For the ignition glow plugs to work correctly, the thermocouples must always be clean. Frequently
check them and, if necessary, clean using a wet cloth and then dry them. Any dry residue must be
removed using a wood toothpick or a needle.
Foster S.P.A. will not answer for the possible inaccuracies contained in this manual attributable to printing
or transcription errors. The right is reserved to make amendments to own products considered necessary or
useful, also in the interest of the utility, without jeopardising its functional and safety features.

182
Riepilogo piani cottura a gas
Legenda
Serie N. Bruciatore Potenza (W)
1 Manopola di comando
II
2 Ausiliario 1.000
3 Semirapido 1.750
4 Rapido 2.700
5 Tripla corona 3.500
10 Dual 4.500
III
6 Ausiliario 1.100
7 Semirapido 1.750
8 Rapido 3.000
9 Tripla corona 3.800
AE
11 Ausiliario 1.100
12 Semirapido 1.750
13 Rapido 3.000
14 Doppia corona 5.000
Tipo di bordo
Bordo standard (8 mm)
Bordo Q4 (4 mm)
Bordo semifilo (3 mm)
Bordo filotop
Fori da incasso
- -
A
B
A = larghezza - B = profondità
ENGLISH ITALIANO
Gas cooker hobs summary
Key
Series No. Burner Power (W)
1 Control knob
II
2 Auxiliary 1.000
3 Semi-quick 1.750
4 Quick 2.700
5 Triple crown 3.500
10 Dual 4.500
III
6 Auxiliary 1.100
7 Semi-quick 1.750
8 Quick 3.000
9 Triple crown 3.800
AE
11 Auxiliary 1.100
12 Semi-quick 1.750
13 Quick 3.000
14 Dual gear 5.000
Edge type
Standard edge (8 mm)
Q4 edge (4 mm)
Semi-flush edge (3 mm)
Flush-mount edge
Holes for built-in
- -
A
B
A = width - B = depth