Four Seasons Courtyard 162455 User manual

WARNING:
● Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of the Gazebo construction.
● Keep assembly area at least 6 feet from any obstruction such as a fence, garage,house,
overhanging branches, laundry line, or electrical wire.
● Some parts may container sharp edges. When assembling and using this product, basic
safety precautions should always be followed to reduce the risk of personal injury and
damage to the product. Please read all instructions before assembly and use
● Check all bolts for tightness before use, and periodically check and tighten bolts as
necessary.
● Gazebo is designed for wind speeds of up to 30 miles per hour. Customer should
disassemble the gazebos when there is a chance of wind speeds higher than 30 miles
per hour.
● Please take down the gazebo during strong wind. The manufacturer or retailer is not
liable for any loss of the product or other items due to the failure to take down the
gazebo during strong wind.
8’X 5’ Grill Gazebo
TV. No: 162455

Post 1 A1 1
Post 2 A2 2
Post 3 A3 1
Base B 4
Base cover C 4
Beam D 4
Center connector E 2
Small top pole G 4
Long screen I 2
Short screen J 2
Glass side bar K1 1
Glass side bar K2 1
Support bar L 4
Hook rack M 1
Bottle opener
（Pre-assembly）N 1
Big canopy O 1
Small canopy P 1
Parts List

AA M6X15 Bolt 8 PCS
BB M6 Flat washer 32 PCS
CC M6X20 Bolt 16 PCS
DD M6X35 Bolt 4 PCS
EE M6 Nut 4 PCS
Z M6 Wrench 1 PC
Hardware Pack 1
Fig.1: Attach base cover (C) to posts (A1,A2,A3) tighten base (B) to the posts (A1,A2,A3) by using bolt ( AA )
and flat washer(BB).
Fig.2: Secure the long screen (I) and short screen (J) to the posts (A1, A2 and A3) by using bolts (CC) and flat
washers (BB).
Fig.3: Insert beam (D) into center connector (E).
Step 1
G
EE
F i g . 5
F i g . 3
F i g . 6
O
D
D
F i g . 4
IJ
F i g . 2
D
A 1
A 2
C
A 3
A 2
F i g . 1

`
Fig.4: Fix beam (D) to posts (A1, A2 and A3) with bolt (DD) and M6 flat washer(BB).
Fig.5: Insert small top pole (G) into center connector (E).
Fig.6: Put big canopy (O) onto the big top, do not fully spread, insert small top pole (G) to beam (D).
AA M6X15 Bolt 15 PCS
BB M6 Flat Washer 15 PCS
HH M6X15 Bolt 2 PCS
GG M6 Flat washer 2 PCS
FF ¢5X160MM Stake 8PCS
Hardware Pack 2
Fig.7: Put small canopy (P), fully spread
big canopy (O), using the hook-loop to
fasten it to the frame; Fix support bar (L)
to glass side bar (K1) and (K2) by using
bolt (AA) and flat washer (BB).
G
D
Fig.6

Fig.8: Fix glass side bar (K2) to post (A2 and A1) by using bolt (AA) and flat washer (BB), also fix glass side
bar (K1) to post (A2and A3) by using bolt (AA) and flat washer (BB).
Fig.9: Attach another end of support bar (K) to posts (A3, A2 and A1) by using bolt (AA) and flat washer (BB).
Fig.10: Attach hook rack (M) to glass side bar (K2) by using bolt (AA) and flat washer (BB).
Fig.11: Lift up the base cover(C),
secure the completely assembled
gazebo into the ground by using
stakes (FF).