Fovno Es-2cs User manual

全电动吸盘行李箱架说明书

FOVNO Electric Sucker Luggage Rack Instructions

Please read these instructions carefully before using this product. The instructions contain important information

which will help you get the best out of the product and ensure safe and proper installation, use and maintenance.

· Do not squeeze or impact the product forcibly.

· Do not disassemble or modify this product.

· Children should be supervised to ensure that they do not use this product as a toy to avoid unnecessary accidents.

· This product needs to be used with the attached alarm, which serves as a reminder during the use of the roof rack. If, when in use, the alarm continues to sound please stop your

vehicle and check our troubleshooting guide. If you are unable to solve the issue, please refrain from using the product until you have contacted customer service.

· In normal use of this product, the suction foot will slowly leak air. When the air pressure inside the leaking suction foot reaches the set minimum pressure value, the N-Power

control box will pump the air automatically, and the alarm will sound. The alarm will stop after a few seconds. The time it takes the N-Power control box to create a vacuum

depends on the hose length and other system settings. Normal operating time is between 2 - 15 minutes and during this time it is normal for the alarm to sound.

· It is normal for the suction foot to leak slowly during use. If the control box starts frequently within 2 minutes(while the alarm keeps buzzing), It is considered to be air leaking too

fast. Frequent start of the control box will cause the internal motor to overheat and not function properly. If similar situations occur, please check whether the suction foot is

damaged, whether the suction part is ﬂat and smooth or whether the hose and quick connector are damaged immediately. If the above problems are removed, but the frequent

start-up phenomenon still occurs, it could mean something is a problem with the product. Please contact customer service immediately. Some products have a particularly

good sealing performance and when the adsorption surface is particularly smooth, it may cause the control box to work automatically at an interval of more than 20 minutes.

If the buzzing alarm doesn't go oﬀ for a long time, please open the suction foot, in which way, you will ﬁnd out if the control box is working normally. If the control box is working

normally, there is no need to worry.

· Before use, please check the battery charge level in the N-Power control box and charge if needed. Do not use with a low battery.

· Before use, please check whether the roof rack control box is working normally with suﬃcient power. Press the control box sunction foot on a smooth surface, turn on the

power switch, and press the control box vertically with your hand. After all the suction foots seal to the surface, open any of the suction foots, the control box should start to

work and this suction foot should re-adsorb the surface immediately, this is what we consider normal operation (Meanwhile, connect to the power of the alarm. the alarm should

start to buzz with the control box starts to work, and stop when the suction foot adsorbed completely).

· Before use, make sure that the ﬁlter sponge at the suction port on the bottom of the suction foot is in good condition. The ﬁlter sponge has a great protective eﬀect on the

adsorption of the suction foot. It prevents dust or other items from entering the suction pipe and guarantees the airtightness of the air valve in the suction foot.

Terms and Conditions

· Before use, please clean the roof area and the bottom surface of the suction foot to be installed with water and dry with a microﬁbre cloth. The suction foot can be installed after

ensuring that the area is free of dust and water.

· When using, please install the roof rack on a ﬂat and smooth part on the roof. The surface where the suction foots are placed must not have cracks. Do not install the roof rack in

places where there vinyl stickers or where there are joins between panels, glass or plastic.

· While driving, check whether the control box is working normally every 4 hours using the method above, and check whether all the suction foots are functioning.

· When using this product, please pay attention to the following items: the highway speed should not exceed 120km/h, and the ordinary road should not exceed the speed limit

sign. Be aware of road conditions and drive slowly on uneven or bumpy conditions.

· There is a lithium battery in the control box of this product. The temperature will aﬀect its eﬃciency. It is recommended to use in an environment at a temperature between

-20°C and +40°C.

· During use, if the control box cannot work normally due to force majeure, please do not panic. Each suction foot of this product is equipped with an air check valve. Even if the

control box is not working normally, the suction foot can still be ﬁrmly adsorbed for at least 1 hour. Please get oﬀ the car in a safe place to check and troubleshoot the problem.

If the control box still does not work normally, please stop using it immediately and contact our company's customer service for repair as soon as possible.

· When the roof rack is not in use, please dust seal plug the air pipe quick interface on the control box and the main suction foot with a rubber plug to prevent foreign objects from

entering and aﬀecting the normal operation of the roof rack.

Learn about your new Electric Sucker Luggage Rack-Hatchback version

Introduction

Pneumatic hose

Front text

N-Power

Control box

Luggage mounting plate

Rear text

Left rear suction feet group

Front liftable suction foot

Front suction foot

Protection cover

Right rear suction feet group

Pneumatic hose

Front text

Right triangle

N-Power

Control box

Luggage mounting plate

Rear text

Left rear suction feet group

Left triangle

Front liftable suction foot

Front suction foot

Protection cover

Right rear suction

feet group

Learn about your new Electric Sucker Luggage Rack-Redan version

Introduction

(Dust seal: When the rack is not in use

please use the dust seal to protect the

pneumatic connections.)

Introduction

Alarm

Pairing

Alarm System Instructions

1. Your rack is ﬁtted with a safety alarm which will alert you if the back loses its connection with the vehicle. The alarm

will sound if a suction foot leaks. In the even of this happening the N-Power system will automatically attempt to create a

vacuum seal using the built in pump.

2. The alarm module is ﬁtted with a standard USB which can be connected to your vehicle either via the vehicles own USB, a

USB adaptor or USB port on a sound system. The alarm will connect to the N-Power box wirelessly and will alert you in the

even of a pressure error. Double sided toe on the underside of the alarm can be used to hold it in place.

3. PLEASE NOTE: If you are using more than one electric rack system on your vehicle the alarm system may not operate

correctly due to a shared signal. While the alarm may not operate the N-Power box will still function as normal.

N-Power control box functions

· Charging: Charging the N-Power box is easy and thanks to the USB-C connector you can charge from a phone charger power

band or a USB charger. Simply remove the waterproof / dust cover and charge with the included USB C wire.

· The N-Power control box features USB lights that tell you the level of charge in the battery. An orange light indicates the system

needs charging, blue means full and a red light indicate the system is being charged. To check the battery level press the button

on the N-Power control box.

N-Power Control Box

Dust seal plug

Quick release air hose connection

USB Type C connector Power button

Battery health check button

(Red light when charging

blue light when fully charged.）

（The blue light is normal, and the red

and orange are charged immediately）

red orange blue blue blue

The underside of the alarm

A button for the pairing switch

Pairing method of alarm and control box

1. Clear data: There is a small hole on the back of the

alarm that is a button for the pairing switch. After the

alarm is connected to the power supply, press the

switch button in the small hole for about 10 seconds

When the indicator light of the alarm is oﬀ, it meansthat

the original data is cleared.

2. Use the same method to press the switch button in

the small hole of the alarm for about 3-5 seconds. After

the alarm indicator lights up, start the control box, and

then stop pressing the pairing switch. At this time, the

alarm buzzes, the pairing is complete.

Suction ﬁlter

Base of foot Gasket

Warning: Ensure the suction foot ﬁlter is clean

and in good condition.

Introduction

Press in hose

Remove the dust seal plug

(please keep it in a safe place)

Hose Connection

Hose Disconnection

① ②

Replace the dust seal

plug when not in use

b.While pressing the lever

carefully pull the hose loose

a.Press the lever to release

the locking interface

① ②

Installation of your Electric Sucker Luggage Rack

Hatchback version and sedan have the same method

What's in the box

Introduction

Name Main Body Suction Foot Group

Right Rear Rack Suction Feet

Group×1

Electric Sucker

Luggage Rack

Hatchback

Version

Accessories Spares

Spare Board×4

Alarm×1

USB Type-C Cable×1

Pipe Fixing Buckle×6

5mm Allen Key×1Carriage Screw×8

Microﬁbre Cleaning Cloth×1

Square Gasket×8

Seals×4

Suction Foot Filters×4

CPC Dust Seal Plug×2

Hose Connector×4

4mm Allen Key×1

Speciﬁcation

Model number ES-T02

Package size 850×180mm

System weight 7.5kg

Protection grade

Executive standard

Our products have acquired the UN38.3、EN62133

IP65

QC/T948-2013

Battery capacity 3400mAh

Input DC 5V

Power 13W

Maximum negative pressure -65KP

Wireless transmission frequency 433.92MHZ

Gaskets×4

Rear Frame×1

Front Frame×1

Left Rear Rack Suction Feet

Group×1

Lubricant ×1

Hand Nut×8

Model number

Package size

System weight

Protection grade

Executive standard

Our products have acquired the UN38.3、EN62133

Battery capacity

Input

Power

Maximum negative pressure

Wireless transmission frequency

Seals×4

Suction Foot Filters×4

CPC Dust Seal Plug×2

Hose Connector×4

Gaskets×4

Nylon Cable Tie

What's in the box

Introduction

Name Main Body Suction Foot Group

Right Rear Rack

Suction Feet Group×1

Left Rear Rack

Suction Feet Group×1

Right Triangle × 1

Electric Sucker

Luggage Rack

Redan version

Accessories Spares

Spare Board×4

Alarm×1

USB Type-C Cable×1Pipe Fixing Buckle×6 5mm Allen Key×1

Carriage Screw×8 Microﬁbre Cleaning Cloth×1

Square Gasket×8

4mm Allen Key×1

Speciﬁcation

ES-T03

850×180mm

9.1kg

IP65

QC/T948-2013

3400mAh

DC 5V

13W

-65KP

433.92MHZ

Rear Frame×1

Front Frame×1 Left Triangle × 1

Lubricant ×1

Hand Nut×8

Figure Ⅰ

Figure Ⅱ

Figure Ⅲ Figure Ⅳ

This product is divided into hatchback version and sedan version, please install it according to the instruction manual of

the purchased product.

Hatchback rear frame installation

1. Install the suction feet group on the rear text, and tighten the screws as shown in Figure Ⅰ. Two spacers should be placed at the connection

to avoid shaking due to excessive clearance.

2. The

pneumatic hose

under the front frame and the rear frame text need to be ﬁxed with pipe ﬁxing buckles, as shown in Figure Ⅱ.

3. After the rear suction feet group is installed, connect the

pneumatic hose

on the rear frame to the joint of the rear suction feet group as shown

in Figure Ⅲ.

Note: During installation, the control box switch and the

pneumatic hose

on the suction feet group

face the rear of the vehicle, as shown in Figure Ⅳ.

The

pneumatic hose

towards the rear of the

vehicle

Fixed pneumatic hose

Instructions

Figure Ⅴ Figure Ⅵ Figure Ⅶ

Tie with nylon ties

Forward Backward

Sedan rear rack installation

1. Install the rear suction feet group and the

triangle

together, as shown in Figure Ⅴ (the left and right directions of the

triangle

have the LOGO

facing outward, and the

triangle

faces the same as Figure Ⅶ). Two spacers need to be placed at the connection to avoid shaking due to

excessive clearance.

2. Install the rear suction feet group with the

triangle

installed on the rear frame, as shown in Figure Ⅵ, place the anti-loose speacer on the

installation place to prevent loosening, and tighten the screws.

3. The

pneumatic hose

under the front frame and the rear frame should be ﬁxed with the pipe ﬁxing buckle as shown in Figure Ⅱ, and the pipe

ﬁxing buckle on the

triangle

should be fastened with nylon cable ties as shown in Figure Ⅶ.

4. After the rear suction feet group is installed, connect the

pneumatic hose

on the rear frame to the joint of the suction feet group as shown in

Figure Ⅲ.

Note: During installation, the control box switch and the

pneumatic hose

on the suction feet group face the rear of the vehicle, as shown in

Figure Ⅳ.

Instructions

The installation is complete

Luggage Installation

1. Measure the distance between the mounting slots/holes on the left and right sides of the luggage compartment, as shown in Figure Ⅷ.

2. Adjust the position of the mounting plate according to the distance between the mounting slots/holes on both sides of the luggage, as

shown in Figure Ⅸ. After adjusting to the proper position, tighten the screws (the adjustment method is the same way for the front and rear frames).

3. Loosen the ﬁxing screws of the mounting plate and the text, adjust the position of the mounting plate, and tighten the screws, as shown in Figure Ⅹ.

Mounting plate can be

moved left or right to

adjust distance

Instructions

Figure Ⅷ Figure Ⅸ

Figure Ⅹ

Adjust the distance between the mounting plates

according to the size between the luggage mounting

holes

The adjustment method of the front frame

and the rear frame is the same way

Loosen the screw

Adjust the mounting plate position

Measure the dimensions between the luggage

mounting holes

？cm

4. After the luggage mounting plate is adjusted, if the p

neumatic hose

is too long, it can be cut, as shown in Figure Ⅺ(the cut oﬀ p

neumatic hose

should be kept in case it needs to be extended when the mounting plate is adjusted to the maximum size, and the

hose

connector is included in

the spares plastic box)

5. If the position of the mounting plate cannot be adapted to the slot/hole position of the luggage compartment, you can use the spare board for

installation, as shown in the Figure Ⅻ. After adjusting to the appropriate position, tighten the screws (the adjustment method of the front frame

and the rear frame is the same), and then connect the p

neumatic hose

Luggage Installation

Instructions

Extend the hoseShorten the hose

The p

neumatic hose

is too long

andcan be shortened

Spare mounting plate

It can be installed outside the suction feet group if the distance

between the mounting holes on both sides of the luggage is too long.

Figure Ⅺ

Figure Ⅻ

Instructions

Front Frame Middle Height Adjustment

1. The height of the suction foot in the middle of the front frame can be adjusted according to the curved surface of the roof, so that the three

suction feet can ﬁt the roof as much as possible.

2. To adjust the method, disconnect the white hose quick connector as shown in Figure XIII-Ⅰ.

3. Rotate the middle suction foot height as shown in Figure XIII-Ⅱ. The suction feet swing back and forth to accommodate the curved surface of

the roof. After adjusting the height, there is no need to lock it.

4. Adjust to the appropriate height and connect the hose quick connector.

5. Front and rear frame p

neumatic

hose connection: The p

neumatic

hose can be connected to the rear frame from the inside of the luggage. The

neumatic

hose inside the luggage needs to be protected by a corrugated pipe as shown in the Figure XIV. When placing items, try to avoid

pressing the p

neumatic

hose to cause the p

neumatic

hose to be blocked or damaged.

Unscrew the interface

Rotate the suction foot to adjust the height to ﬁt the curved surface of the roof

Figure XIII-Ⅱ

Figure XIV

Figure XIII-Ⅰ

Figure XVI

Instructions

Luggage Installation

Thread the carriage screws

into the mounting plate

1. Install the luggage rack on the luggage, select the appropriate position of the installation slot/hole, and use carriage screws, square gaskets and

hand nuts to ﬁx as shown in the Figure XV.

2. After ﬁxing, place the luggage rack and luggage on the roof as a whole, choose a suitable position, turn on the power switch, and attach the

suction feet to the roof. Fit the roof to complete the adsorption, and the installation is complete, as shown in the Figure XVI.

Apply vertical downward pressure on the suction feet

by hand so that each suction foot is secured to the roof

Figure XV

Trouble Shooting

Problem Possible Issue Solution

The USB is not connected to the power interface. Please check USB connection

and power source.

Alarm is damaged.

Low power in battery.

Contact customer service.

Fully charge and retry.

Battery is damaged. Contact customer service.

Loose connectoin. Check wires are connected properly.

System is in sleep mode. Use as normal.

Not the above and still not working. Contact customer service.

Damaged suction foot. Contact customer service.

Poor seal due to uneven/cracked surface. Move system.

Replace ﬁlter.

Replace Hose.

Lost ﬂiter.

Damage to hose.

Alarm is not functioning

Control box is not functioning

Control box lights is not

functioning when charging

Suction foot is not functioning

Warranty

The after sales service of this Electric Sucker Luggage Rack is strictly based on the“Consumer Rights Protection of the People's Republic of China”and“Product

Quality Law of the People's Republic of China”to implement after-sales three-guarantee service, the service content is as follows:

Warranty period

1. If the product fails to perform within 7 days of purchase, it should be tested by the manufacturers after sales service centre to determine if there is a fault.

2. Within 8-15 days from the next day after you sign for the product, if the product has performance failures listed in the“Electric Sucker Luggage Rack Performance Failure

List”, it can be determined by the manufacturer's after-sales service centre. Enjoy free replacement or repair services.

3. Within 12 months from the day after you sign for the product, if the product has performance failures listed in the“Electric Sucucker Luggage Rack Performance Failure List”,

it has been tested and determined by the manufacturer's after-sales service centre, and you can enjoy it for free Maintenance service.

Issues not covered by this warranty

1. Unauthorised maintenance, misuse, collision, negligence, liquid ingress, accident, altercation, incorrect use of this product and its accessories, remove or altering labels or

anti-counterfeiting marks.

2. The validity period of the warranty has expired.

3. Damage caused by force majeure.

4. Issues not met in the performance failures listing.

5. Due to human reasons, the product and its accessories have the performance failure listed in the“Electric Suction Foot Luggage Rack Performance Failure List”.

Electric Sucker Luggage Rack Performance Failure List

1. Control box is not functioning.

2. Control box is not charging.

3. Alarm is not functioning.

4. Suction feet are not creating a vacuum with no visible damage.

Electric Sucker Luggage Rack

Name Performance failure

Maintenance

The pneumatic air hoses and interlocking interfaces should be coated with a silicone based oil to ensure sealing performance.If a suitable lubricant cannot be found, an edible oil

can be used as a substitute.

When the bike rack is not in use please disconnect pneumatic air hoses and replace the dust seal plug to prevent dirt or debris from entering the system.

After use please ensure the battery in the control box is fully charged. If you do not use this product for a long time, the battery in the control box will lose power, please check the

power every three months and charge it in time.

Warranty Card

User name

Address

Telephone number

Product name and model

Purchase date

Maintenance Record

Number Date Fault Description and Replacement Accessories Service Center Service engineer