FOVNO RS-H1B User manual

手 动 倒 立 吸 盘 车 顶 架 说 明 书
FOVNO Manual Inverted Sucker Bike Rack Instructions

11
Learn about your new Manual Inverted Sucker Bike Rack
Introduction
Handlebar strap
Handlebar clamp
Cylinder rod
Suction foot
Safety strap
Saddle strap
Saddle holder
Saddle suction foot Handelbar suction foot
Handelbar suction foot
Safety suction foot
Strap buckle

12
What's in the box
Introduction
Name Safety Suction Foot
Manual Inverted
Sucker Bike Rack
Due to transportation regulations, the maintenance oil may be taken out of the packaging, please buy silicone oil at the local market or bike shop, If you cannot buy silicone oil,
you can temporarily replace it with edible oil.
Handelbar Suction Foot
×2
×1
×1
Saddle Suction Foot Accessories
Specification
Model Number
Package Size
System Weight
Carry Capacity
Executive standard
1 bike
QC/T948-2013
RS-H1B
370×160×140mm
2.3kg
Our products have acquired the CE-ROSH、UKCA、CA Prop65、CPSIA certification.
250×40mm
Crank Strap×1
Microfibre
Cleaning
Cloth×1
Lubricant ×1

13
The handlebar suction foot installation
Instructions
Install handlebar Remove the handlebar
Lock the handlebar
Shake
Tighten the handlebar
Penetrate
Release handlebar
Press button
Remove handlebar
Pull apart

1
4
2
3
14
Bundling position
Strap installation
Strap removal
Figure Ⅰ
1. Press button
2. Take out the straps
1
2
The safety suction foot installation
After putting the bike upside down on roof of the car, be sure to install the safety suction foot. The binding position of the safety suction foot is
shown in Figure Ⅰ. Install the safety suction foot under the bike aheadset stem , and the safety strap must pass between the bike down tube and
the fork before tying up.
Note: Use safety suction foot must be used to use this product.
Instructions
1. Press button
2. Thread the strap
3. Release the button
4. Tighten the strap

The saddle suction foot installation
Select the mounting
holes according to the
actual situation
Binding behind the seatpost
15
Suction foot adsorption and removal:
1. Before installation, clean the installation position and suction foot to avoid dust affecting the sealing, or water accumulation causing the suction foot to be slippery.
2. Press the suction foot vertically against the roof with one hand, and push the cylinder rod with the other hand to draw out the air, as shown in Figure Ⅱ, until the white line
enters the pump. Make sure that the cylinder rod has no obvious return.
3. After use, remove it from the edge of the suction foot by hand as shown in Figure Ⅲ,make the air into the suction foot,then take it out.
Instructions
Figure Ⅱ Figure Ⅲ
Press the cylinder rod Peel along the edge of the suction foot
Press vertically

Be sure to install a safety
suction foot
16
Installation method 1
1. Install the handlebar suction feet and saddle suction foot on the bike, fasten the straps, and the bottom of all suction feet are horizontally upward, and the cylinder rod is facing
the rear of the bike, as shown in Figure 4.
2. Invert the bike to the roof of the car, adjust the bike to be parallel to the car, adjust the position of the handlebar suction foot and the saddle suction foot, so that the bottom surface of the
suction foot and the installation surface are completely fitted,absorb all the suction feet.
3. Place the safety suction foot under the bike aheadset stem, absorb the suction foot, and the safety strap must pass between the bike down tube and the fork before tying up, as
shown in Figure Ⅴ.
Instructions
Figure Ⅳ Figure Ⅴ

Be sure to install the safety
suction foot
17
Instructions
Installation method 2
1. Open the handlebar suction feet and place them in the selected position as shown in Figure VI. The distance between the two is determined by the length of each side of the bike
handlebar.
2. Attach the saddle suction foot to the bike saddle and fasten the straps, making sure that the strap is tied behind the seat tube.
3. Hang the handlebars of the bike on the handlebar clamps, tie the handlebars tight, and absorb the saddle suction foot.
4. Place the safety suction foot under the bike aheadset stem, absorb the suction foot, and the safety strap must pass between the bike down tube and the fork before tying up, as
shown in Figure Ⅶ.
Figure Ⅵ Figure Ⅶ
Installed on the rear of the car, you need to confirm the
suction position of the suction foot. once installed, the
bike does not block the license plate.

Precautions
1. Place cylinder rod toward the rear of the car to avoid the wind and dust entering into the cylinder rod.
2. Before driving,check the handlebar suction feet and saddle suction foot are tight with bike and car,And whether the safety suction foot strap is fastened.
3. Please stop the car to check the bike rack about every 4 hours, ensure the bike handlebars and saddle with suction feet are tight, and ensure that there is no sign air leakage from the suction
feet.(If the white line is outside of the pumpwhich means the suction is leaking, you should push the cylinder rod until it comes into pump.)
4. The speed in normal roads should not exceed the speed limit. The speed in highways should not exceed 120km/h. Please slow down when cornering and drive slowly in bumpy roads.
5. In order to avoid the crank shaking caused by the bumps during driving, the crank should be fixed to the bike frame with crank strap.
120
Check the white line 120km/h speed limit Sharp turn Bumpy road Tie the crankand the frame
18
Precautions and Maintenance
Maintenance
1. Please clean the removed suction feet in time and put it in the storage bag for storage.
2. Cylinder maintenance oil is used to maintain the cylinder, make the cylinder more lubricated and seal better.
Maintenance method: ①Pull out the cylinder rod; ②Drip the maintenance oil into the cylinder pipe; ③Apply the maintenance oil to the front piston of the cylinder rod;
④Install the cylinder rod.
Notice:There is no regular time for the cylinder maintenance.
If you use it frequently, please maintain it once a month.. If not, please check and ensure that the cylinder is lubricated before use.
①② ③ ④

19
Trouble Shooting
Possible lssue Troubleshooting method Solution
The cylinder rod shows
a white mark for a short
time
The suction foot cannot
be attached to the roof
Lack of maintenance oil in
the cylinder
The live rubber piston at
the front end of the
cylinder rod is damaged
The interface between the
cylinder and the suction
foot is damaged
Damaged bottom surface
of suction foot
Cracks and bumps on the
adsorption surface
The suction foot does not
fit completely
Pull out the cylinder rod to check the condition of the front end
of the cylinder rod. If the rubber piston at the front end is not
abrasion, no liquid silicone oil
Add maintenance oil to the cylinder or
the front end of the cylinder rod. If there
is no maintenance oil, you can add a few
drops of cooking oil instead.
Please contact our after-sales service to
provide repair parts
Please contact our after-sales service to
provide repair parts
Please contact our after-sales service to
provide repair parts
Transfer the suction foot to a flat,
smooth surface without cracks
Press the suction foot vertically and
firmly with one hand to make the suction
foot fully fit with the suction surface,
and quickly press the cylinder rod with
the other hand to exhale.
Pull out the air cylinder rod to check the condition of the front
end of the cylinder rod. If the rubber piston at the front end is
worn If it is damaged pull it out, please insert the normal cylinder
rod on the other suction foot into this suction foot, and then after
the replacement, the suction foot is no longer white for a short time
After the above two methods are excluded, the cylinder rod is still
white for a short time, it may be the position where the cylinder
and the suction foot meet is damaged, remove the plastic base on
the suction foot and check if the part is damaged
Check the bottom of the suction foot for damage
Check the suction surface for cracks, bulges, etc.
Check whether the bottom surface of the suction foot is completely
attached to the suction surface
Problem