Foxun SX-SPH04-70 User manual
Operating Instructions
1
70m 1x4 HDBaseT Splitter, HDCP2.2 compliant
Support POC, RS232 Pass through
Features
•Incorporate HDBaseT technology
•Distribute 1Ultra HD HDMI signal to 4 identical HDBaseT outputs, with 1x loop HDMI output
•HDCP 2.2/1.4 compliant
•Transmitter Distance up to 70m under 1080p, 40m under 4K
•Support resolution to 4K@60Hz, YUV 4:2:0, VESA resolution up to 1920x1200
•Support Dolby TrueHD, DTS-HD Master Audio
•With wide-band Bi-Directional IR control (38 ~ 56 kHz)
(IR extension from Sender to Receiver or from Receiver to Sender)
•HDBaseT output 1 supports RS232 and Ethernet pass through
•Support 3D
•Support POC (Receiver powered by HDBaseT Splitter)
•DC 12V power supply
Operating Instructions
2
Operating Instructions
7
-5 to +35 C(+23 to +95 F)
5 to 90%RH (No Condensation)
10.2Gbps
Resolutions
up to 4K@60Hz, YUV 4:2:0
VESA
resolution
1x HDMI input
1x HDMI loop output
4x RJ45 output
2x Power DC receptacle
1x Phoenix RS232 port
70m(1080P), 40m(4K)
110-240V/ 12V DC power supply
15Watts
L305xW165.2xH39.8mm
1425g
Packing contents
1) Main Unit: 1x4 HDBaseT Splitter
2) 2x Power supply DC 12V
3) 4x IR-TX cable
4) 4x IR-RX cable
5) 1x Phoenix plugs for RS232 cable termination
6) 4x screws
7) 2x detachable mounting ears
8) Operating Instruction manual
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Panel Descriptions
Connecting and Operating
Applications
Maintenance
Product Service
Warranty
Operating Instructions
6
Operating Instructions
3
VESA Resolution
Refresh rate VESA Resolution
59.94Hz 640x480
640x480
800x600
1024x768
1280x768
1280x960
1280x1024
1680x1050
1920x1080
1280x720
1360x768
1400x1050
1920x1200
60Hz
Dimensional drawing
2
Operating Instructions
4
Operating Instructions
5
Please restart the splitter when change EDID mode!
Front Panel
Rear Panel
Power ON/OFF
1Indicator of Loop out
2
Indicator of out
3
Reset button
5Indicator of Power
6
DIP switch for EDID setting
4
RS232 port
7
Output1 port (RS232 pass-though)
1
1 2 342256
3
5POC port
Note:
Connecting and operating
1) Connect the HDMI input source into HDBaseT splitter.
2) Connect HDBaseT splitter and Receiver over Cat6 cable, The Cat6 cable must follow
EIA-TIA 568b standards.
3) Connect the HDMI output of Receiver to the HDMI Display.
HDMI Input port
Main power
HDMI Output port
2
4
6
Output2,3&4 port
EDID
0 0
0 1
1 0
1 1
4K@60Hz、YCBCR420、3D、DOLBY5.1
1080P@60Hz、2CH
1080P@24Hz、3D、DOLBY5.1
4K@30Hz、2CH
7) To get on the ethernet,pls connect as below steps:
1.Connect ethernet cable into ethernet port on HDBaseT splitter.
2.Connect ethernet cable with TV and ethernet extender receiver.
Note:1.The ethernet function is designed for ethernet compatible receiver units only.
2.Only output1 with ethernet function.
8) Copy EDID function
Copy the EDID of the sink which connected the loop HDMI.
4) Connect 4pcs IR TX cables to the IR-TX sockets on the splitter and connect 4pcs IR RX cables
to the IR-RX sockets on the splitter.
5) Connect IR RX cable to IR-In port of Receiver, connect IR TX cable in to IR-Out port of Receiver.
6) Power up all units, the splitter,Receiver, sources and displays.
