
8
2.2.2 Connecting the machine to the tractor
1. Before each connecting and disconnecting of the machine to the tractor, block hydraulic controls to prevent any
unwanted lifting or lowering.
2. When connecting the machine to the tractor, make sure that the connection points of the tractor correspond to
connection points of the machine.
3. Zone around the connection points is very dangerous, so be very careful.
4. When using external commands for hydraulics do not stand between the tractor and the machine.
5. Block the lateral movement of the connecting levers of the tractor during transport.
6. When transporting the machine, fix controls for the tractor hydraulics to the appropriate position.
7. Do not work and transport the machine with a tractor with narrow track width on uneven (bumpy) and sloping
ground.
2.2.3 Hydraulic installations
1. ATTENTION! Hydraulic installation of the machine is under high pressure (maximum operating pressure is 200 bar).
2. When connecting hoses of hydraulic cylinder make sure that the connectors fit properly.
3. When connecting the hydraulic hose couplings on the tractor hydraulic outlet make sure that the installation of the
hydraulics is under no pressure both on the side of the tractor and on the side of the machine.
4. We recommend that you check the connectors for hydraulics, to avoid wrong connection. By replacing connectors of
the reverse function (lifting-lowering) there is a risk of an accident.
5. Regularly check hydraulic hoses and make sure you replace them after 5 years of use at the most. Immediately replace
the damaged or worn hoses. Replaced hoses must meet the technical requirements of the machine manufacturer.
6. If you notice leaking in the hydraulic system, take all the necessary actions to avoid an accident.
7. The outbreak of hydraulic fluid under high pressure can penetrate the skin and cause injury. In case of injury seek
medical attention immediately! There is a risk of infection!
8. Before working on hydraulic installations, lower the machine to the ground, release the hydraulic installation from
pressure and turn off the tractor engine.
2.2.4 Maintenance
1. Before checking for possible improper operation of the machine or before setting up, maintaining or repairing the
machine, turn off the engine of the tractor, remove the ignition key and pull the parking brake of the tractor.
2. Regularly check the tightness of the screws and nuts. Tighten them if necessary.
3. In the event that the machine is lifted, secure and strengthen it by using the appropriate support before any action on
the machine.
4. Spare parts must comply with the standards and recommendations of the manufacturer. Use only original spare parts
of FPM Agromehnika.
5. Repairs on the parts which are under pressure or are stressed (hydraulic cylinders, hoses, springs, etc.) may be
performed only by the trained staff with appropriate equipment for such works.
2.2.5 Specific recommendations
1. Keep a safe distance from the collector when in operation.
2. Each time before using the collector, make sure that all the parts (nuts, bolts, etc.) are adequately tightened.
3. For safe use it is particularly important that collecting elements are properly installed. Use only parts and tools
recommended by the manufacturer.
4. Before each use of the collector, check the collecting elements. In case that they are damaged or too worn, replace
them immediately.
5. Remove from the working area (fields) any foreign objects that may damage the machine and threaten your safety
6. Never work with the machine when reversing.
7. In case of crashing into an obstacle, immediately stop the tractor, turn off the engine, remove the ignition key of the
tractor and wait for all moving parts to stop moving. Check the condition of the whole machine before proceeding
with the work.
8. When turning the collector into the transport position and vice versa make sure that no one is in the path of the swing
of collecting wheels bearings.
9. Secure transport position by shortening the active length of the third lever (toplink).
10. When transporting, take care of the height of the collector with respect to the maximum height to move in a certain
way.
11. We recommend that the authorized servicer check the condition of your machine, particularly the condition of the
collecting elements after every season.