FPV 2015 NEW SKYWALKER 1830 User manual

FPVModel:http://www.fpvmodel.com

2015 NEW SKYWALKER 1830 FPV PLANE
USER MANUAL
Thank you for purchasing the 2015 New Skywalker 1830 FPV
Plane. The 2015 New Skywalker is specially designed for First
Person View (FPV) applications.
FPV Model
http://www.fpvmodel.com
E-mail: [email protected]
Tel: [phone]

FPVModel:http://www.fpvmodel.com

Specifications:
•1. Wingspan: 1830MM (single wing length:850mm)
•2. Fuselage length: 1270MM
•3. Wing area: 41.06 dm2
•4. Flying weight: 2500g-3000g
•5. Centre of gravity：Backwards 90-100mm from wing front edge
Recommended Parts (not included)：
•1. Motor: 2820KV850-900
•2. ESC 45A-60A
•3. Servo: 12g*4pcs
•4. Prop: 12-13 inch
•5. Battery: 14.8v 5500mah
•6. Radio: 4CH
Features：
•1. Plane cabin adopts with the air layer plate structure which improves the strength of fuselage but
minus the weight. The inner cabin with three layers, and convenient for you equipments mounting.
•2. The wing includes 4 carbon strips and one 12mm carbon tube, 1820mm wingspan. High
maneuverability with quick detaches structure, easy to detach and carry.
•3. The fuselage with reserved position for GPS, TX/RX and camera. Logical position arrangements
avoid the interference with each other and good form aching cooling.
•4. Reasonable design. Reserved space in the nose for brushless 3-axis gimbal mounting. With built
in air aluminum alloy landing gear, you will no worry about the landing issues.
•5. The plane tail adopts 3K tube to connect the fuselage. Light weight (53g) and durable.（winded by
fiber cloth）
•6. Quick mounting clip for Horizontal tail and vertical tail to fasten. Composited by independent part
for easy to detach and mount.
•7. As per our test, the plane can be mounted with SONY RX1!
•8. Support the catapult launch.

FPVModel:http://www.fpvmodel.com

KIT version configuration：
Fuselage, wing, Horizontal tail, tube, accessories bag, sticker
Parts listing:
(Note: The color of plastic parts may be different from the actual items that you received. Please
be subject to the pictures on product page.)

FPVModel:http://www.fpvmodel.com

（安装过程中，飞机泡沫件和配件全部用胶水沾粘。）
1.首先安装机身机舱，将层板配件沾粘固定在机舱内。
详情见下图；
(During the installation process, the plane foam pieces and accessories need to be glued .)
1. Install fuselage cabin, stick and secure the layer board accessories in the cabin.

FPVModel:http://www.fpvmodel.com

2.安装机身外围层板配件。为了保证机身沾粘时不会出现误差，请用相应的碳管和层板卡入各部位，
这样机身沾粘才能吻合连接。
详情见下图；
2. .Install the outside plate parts of fuselage. To make sure correctly glue to the fuselage, please
use the corresponding tubes and layer boards into different parts, so as to match the connection
when glue to the fuselage.

FPVModel:http://www.fpvmodel.com

3.装起落架和舱盖。
详情见下图；
3. Installation of the landing gear and hatch covers.

FPVModel:http://www.fpvmodel.com

4.机身电配安装。电机、电调、电池、桨可在机身完成后安装。
详情见下图；
4. Electrical installation. Motor, ESC, battery, and propeller can be installed after the completion of
fuselage installation.

FPVModel:http://www.fpvmodel.com

5.垂尾安装。先将塑料件沾好固定，再排好延长线，然后沾粘固定。
详情见下图；
5. Vertical tail installation. Plastic parts glued first, and then the extension cord, and then glued and
secured.

FPVModel:http://www.fpvmodel.com

6.平尾及舵机安装。把调试好的舵机固定在槽内，再将塑料件沾粘固定。
详情见下图；
6. Flat tail and the steering gear installation. To have a good debugging of the steering gear is fixed
in a groove first, and then stick plastic parts.

FPVModel:http://www.fpvmodel.com

7.舵角和拉杆安装。
详情见下图；
7. Rudder Angle and pull rod installation.

FPVModel:http://www.fpvmodel.com


FPVModel:http://www.fpvmodel.com

8.机翼安装。将调试好的舵机和相应的加强配件沾粘固定。
详情见下图；
8. Wing installation. Stick the servo which has adjusted well to the corresponding strengthening
parts and secured.

FPVModel:http://www.fpvmodel.com

9.重心：机翼前缘向后 95-100MM。
详情见下图：
9. Centre of gravity: Leading edge back 95-100 MM.
10.安装完成；
10. Finally the installation is completed.

FPVModel:http://www.fpvmodel.com

Thanks for Watching!