Franke FRE604B1 User manual

FRANKE
SPECIFICATIONS
Recommended use Domestic
Material Black Glass
Colour availability Black
Weight 9kg
Dimensions 40 x 590 x 520mm
Zones 4
Control type Touch
Voltage 220-240V/50-60
Max power KW 6.0
FR Capacity (KW) 1.8
BR Capacity (KW) 1.2
FL Capacity (KW) 1.8
BL Capacity (KW) 1.2
Highlight Yes
Auto shut-off Yes
Overheat indicator Yes
Power connection Hardwired
CLEANING RECOMMENDATIONS
To see the complete FRANKE range go to
www.reece.com.au/bathrooms
DESIGNER CERAMIC COOKTOP 60 CM
• Switch-off the appliance before cleaning.
• Do not clean the hob if the glass is too hot because there is a risk of burn.
• Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then rinse with cold water and dry the
surface thoroughly.
• Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided.
• Do not ever use any steam-cleaner or pressure washer.
• Do not use any object that may scratch the ceramic glass.
• Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your ceramic hob or on the pan. Sliding rough
saucepans will scratch the surface.
• Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the surface being damaged.
• Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
Dimensions are nominal measurements only.
Disclaimer: Products in this specication manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor
reserves the right to vary specications or delete models from their range without prior notication. Dimensions are nominal measurements only.
Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
40mm
490mm
560mm
520mm
590mm
page 1 of 3

INSTALLATION INSTRUCTIONS
FRANKE
DESIGNER CERAMIC COOKTOP 60CM
page 2 of 3
Plumbers, please ensure a copy of the installation instructions
is left with the end user for future reference
The installation comes under the exclusive responsibility of specialists.
The installer is held to respect the legislation and the standards enforce in his home country.
How to stick the gasket:
The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.
This installation has to be done carefully, in conformity of the following drawing.
• Stick the gasket (2) two millimetres from the external edge
of the glass, after removing the protection sheet (3)
Fitting - installing:
The cut out sizes are:
• Ensure that there is a distance of 50 mm between the hob and the wall or sides.
•The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed with plenty of space on either
side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must
stand higher than the hob.
•The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings
and the glue used to fix them, must be able to resist temperatures of up to 100 °C.
• The mural rods of edge must be heat-resisting.
•Do not install the hob to the top of a nonventilated oven or a dishwasher.
•To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic
device.
•If a drawer is placed under the work, avoid to put into this drawer flammable objects (for example: sprays) or not heat-
resistant objects.

INSTALLATION INSTRUCTIONS
FRANKE
DESIGNER CERAMIC COOKTOP 60CM
page 3 of 3
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
• Materials which are often used to make worktops expand on contact with water. To protect the cut out edge, apply a coat of
varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any
leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top
surfaces.
• The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer.
In case of absence of instructions respect a distance minimum of 760 mm.
• The connection cord should not be subjected to mechanical constraint, for example a drawer.
•WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer
of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate
guards can cause accidents.
ELECTRICAL CONNECTION
• The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician
perfectly to the fact of the normative regulations and which respects them scrupulously.
• Protection against the parts under tension must be ensured after the building-in.
• The data of connection necessary are on the stickers placedon the hob casing near the connection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact
opening of at least 3 mm.
•The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contac-
tors.
•If the appliance is not fitted with an accessible plug, disconnecting means must be incorporated in the fixed installation, in
accordance with the installation regulations.
• The inlet hose must be positioned so that it does not touch any of the hot parts of the hob.
CAUTION!
This appliance must only to be connected to a network 230 V~ 50/60 Hz.
Always connect always the earth wire.
Respect the connection diagram.
The connection box is located underneath at the back of the hob casing. To open the cover use a medium screwdriver. Place it
in the slits and open the cover.
We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an ap-
pliance which has not been earthed or has been equipped with a faulty earth connection.
CONNECTION OF THE HUB FOR:
Mains Connection Supply Cord Supply Cord Circuit Braker
230V~ 50/60Hz 1 Phase + N 3 x 2,5mm2H 05 VV - F
H05 RR - F
25 A *
400V~ 50/60 Hz 2 Phases + N 4 x 1.5 mm2H 05 VV - F
H 05 RR - F
16 A *
* calculated with the simultaneous factor following the standard EN 60 335-2-6
Connection of the hob
For the various kinds of connection, use the brass bridges which are in the box next the terminal
Monophase 230V~1P+N
Put the 1st bridge between terminal 1 and 2
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L to one of the terminals 1 or 2.
Biphase 400V~2P+N
Attach the earth to the terminate “earth”, the neutral N to terminal 4, the Phase L1 to the terminals 1 and the Phase L2 to the
terminal 2.