Jenn-Air JED4536WS02 User manual

JENN-AIR°
30" (76.2 CM) AND 36" (91.4 CM) ELECTRIC
DOWNDRAFT COOKTOP INSTALLATION INSTRUCTIONS
INSTRL)CTIONSD'INSTALLATION DE LA TABLEDE
CUISSON ELECTRIQUEAVEC ASPIRATION PARLEBASDE
30" (76,2 CM) ET36" (91,4 CM)
Table of Contents/Table des mati_res
COOKTOP SAFETY .................................................................... 2
INSTALLATION REQUIREMENTS ............................................ 2
Tools and Parts......................................................................... 2
Location Requirements ............................................................ 3
Venting Requirements .............................................................. 4
Venting Methods ...................................................................... 5
Electrical Requirements ............................................................ 7
INSTALLATION INSTRUCTIONS .............................................. 7
Prepare Oooktop ...................................................................... 7
Install Foam Strip ...................................................................... 8
Rotate Blower - Optional .......................................................... 8
Install Oooktop .......................................................................... 8
Make Electrical Oonnection ..................................................... 9
Oomplete Installation.............................................................. 10
SECURITE DE LA TABLE DE CUlSSON .................................... 11
EXIGENCES D'INSTALLATION .................................................. 11
Outillage et pieces ..................................................................... 11
Exigences d'emplacement ........................................................ 12
Exigences concernant I'evacuation .......................................... 14
Methodes d'evacuation ............................................................. 15
Specifications electriques ......................................................... 16
INSTRUCTIONS D'INSTALLATION ............................................ 17
Preparation de la table de cuisson ............................................ 17
Installation de la bande de mousse .......................................... 17
Rotation du ventilateur - Facultative ......................................... 18
Installation de la table de cuisson ............................................. 18
Raccordement electrique .......................................................... 19
Achever I'installation .................................................................. 20
iMPORTANT:
Save for local electrical inspector's use.
iMPORTANT :
,&,conserver pour consultation par I'inspecteur local des installations 61ectriques.
W10436037A

COOKTOP SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
• Tape measure
• Flat-blade screwdriver
• Phillips head screwdriver
• Drill
• Level
• 6" socket extension
• Marker or pencil
•Pliers
• 1_,, drill bit
•Jigsaw
• Ratchet with 3/8"socket
Parts supplied
• Vent grille
• Pre-filter
Parts needed
• A ULlisted or CSA approved strainrelieffor %"(2.2 cm)
knockout.
• A UL listed or CSA approved conduit connector for
V2"(1.3 cm) trade-size metal-clad conduit
• UL listed wire connectors
Metal ducting
Jenn-Air ®wall cap
Jenn-Air®6 '' (15.2 cm) Round Surface Wall Cap Damper
Order Part Number A406
Jenn-Air ®31¼"x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper
Order Part Number A403
To order, see the "Assistance or Service" section of the Use
and Care Guide.
• Vent clamps
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
2

IMPORTANT: Observe all governing codes and ordinances. 36" (91.4 cm) Cooktop - for standard and electric models
When installing cooktop, use minimum dimensions given.
• To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
• Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
• Grounded electrical supply is required. See "Electrical B
Requirements" section.
• If cabinet has drawers, drawers will need to be removed and A
drawer fronts installed on front of cabinet.
IMPORTANT: An under-counter built-in oven cannot be installed
under this product.
A. Model/serial rating plate location
B. 20_/' (52.3 cm)
C. 22" (55.9 cm)
Product Dimensions
30" (76.2 cm) Cooktop - for standard and electric models
A. Model/serial rating plate location
B. 20_" (52.3 cm)
C. 22" (55.9 cm)
G
,F_
A
@' @ @ t #_ @ @
/
°=
C
E_
_D_
A. 29¾" (75.6 cm)
B. 12½" (31.8 em)
centerline of product to
edge of burner box
C. 12½" (31.8 cm)
D. 28 _" (73.3 cm)
E. 12½" (31.8 cm)
F. 2" (5.1 cm) recommended minimum
cabinet to motor clearance
G. 18" (45.7 cm)
H. 4_" (11.8 cm)
G
A. 35 r½/, (89.8 cm)
B. 12_" (32.8 cm) centerline of
product to edge of burner box
C. 12_" (32.8 cm)
D. 34 _" (87.3 cm)
A
B_
D
E. 12½" (31.8 cm)
F. 81_4" (20.9 cm)
recommended minimum
cabinet to motor clearance
G. 18" (45.7 cm)
H. 4_" (11.8 cm)

Cabinet Dimensions
G
A. 30" (76.2 cm) on 30" (76.2 cm) models
36" (91.4 cm) on 36" (91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet (24" [61 cm]
minimum clearance if bottom of wood or metal cabinet is covered
by not less than ¼" [0.6 cm] flame retardant millboard covered with
not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless
steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E.2"(5.1 cm)
F 21 '_" (73.4 cm)
G. 18" (45. 7cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
I.Junction box or outlet; 10" (25.4 cm) from right-hand side of
cabinet
J. 28 _" (73.4 cm) on 30" (76.2 cm) models
34V2" (87.6 cm) on 36" (91.4 cm) models
K. 2V2" (6.4 cm) minimum distance to nearest left and right side
combustible surface above cooktop
L. 1V2"(3.8 cm) minimum clearance between back wall and
countertop
NOTES: After making the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the cooktop base. To avoid this modification, use a base cabinet
with sidewalls wider than the cutout.
• A minimum side clearance of 6" (15.2 cm) is recommended
between side of cooktop and side wall for maximum
ventilation performance.
• A minimum clearance of 2" (5.1 cm) is recommended
between the motor/blower and cabinet for proper cooling. A
6" (15.2 cm) clearance is recommended for servicing access.
Cutout Dimensions
H
A. 28_" (73.4 cm) maximum on 30" (76.2 cm) models
34V2" (87.6 cm) maximum on 36" (91.4 cm) models
B. 21 _" (53.7 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)
models
C. 8_" (21.9 cm) on 30" (76.2 cm) models
15_" (39.2 cm) on 36" (91.4 cm) models
D. 6_" (16.0 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models
E.2" (5.1 cm) minimum space to front edge of cooktop
F Floor exhaust option
G. 6 _" (15.6 cm) for 6" (15.2 cm) vent system
H. 8_" (21.9 cm) on 30" (76.2 cm) models
15_" (39.2 cm) on 36" (91.4 cm) models
I. 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models
J. Waft exhaust option
IMPORTANT: This cooktop must be exhausted outdoors unless
using the Jenn-Air®Duct FreeFilterAccessory Kit. See "Venting
Methods" section.
• Do not terminate the vent system in an attic or other enclosed
area.
• Use a Jenn-Air ®vent cap.
• Vent system must terminate to the outside.
• Use only a 6" (15.2 cm) round metal vent. Rigid metal vent is
recommended. For best performance, do not use plastic or
metal foil vent.
• Before making cutouts, make sure there is proper clearance
within the wall or floor for the exhaust vent.
• Do not cut a joist or stud unless absolutely necessary. If a
joist or stud must be cut, then a supporting frame must be
constructed.
• The size of the vent should be uniform.
• The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.
• Use vent clamps to seal all joints in the vent system.
• Use caulking to seal exterior wall or roof opening around the
cap.
• Determine which venting method is best for your application.

For Best Performance:
• Use 26-gauge minimum galvanized or 25-gauge minimum
aluminum metal vent. Poor quality pipe fittings can reduce
airflow. Flexible metal vent is not recommended.
NOTE: Local codes may require a heavier gauge material.
• Metal duct may be reduced to 30-gauge galvanized steel or
26-gauge aluminized steel if allowed by local codes. This
reduction is based on information in the International
Residential Codes Section M1601.1 (2006 edition).
• Do not install 2 elbows together.
• Use no more than three 90° elbows.
• If an elbow is used, install it as far away as possible from the
hood's vent motor exhaust opening.
• Make sure there is a minimum of 18" (45.7 cm) of straight
vent between the elbows if more than one elbow is used.
• Elbows too close together can cause excess turbulence that
reduces airflow.
• Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 31/4"x 10 ''
(8.3 x 25.4 cm) system.
• Do not reduce to a 5" (12.7 cm) system after using
6" (15.2 cm) or 31/4'' x 10" (8.3 x 25.4 cm) fittings.
• Avoid forming handmade crimps. Handmade crimps may
restrict airflow.
• Use a Jenn-Air ®vent cap for proper performance. If an
alternate wall or roof cap is used, be certain the cap size is
not reduced and that it has a backdraft damper.
• Use vent clamps to seal all joints in the vent system.
• Use caulking to seal exterior wall or roof opening around the
cap.
The length of vent system and number of elbows should be kept
to a minimum to provide efficient performance.
The maximum equivalent length of the vent system is 60 ft
(18.3 m). For altitudes above 4,500 ft (1272 m), reduce
recommended vent run by 20% for best performance.
Cold Weather Installations
An additional backdraft damper should be installed to minimize
backward cold air flow and a thermal break installed to minimize
conduction of outside temperatures as part of the vent system.
The damper should be on the cold air side of the thermal break.
Makeup Air
Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of air
movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your
area.
Common venting methods are shown for a counter-mounted
downdraft cooktop. The cooktop may be vented through the wall
or floor.
Option 1 - Roof Venting Option 2 - Wall Venting
A. Roof cap
B. 6" (15.2 cm) round roof venting
Option 3 -Venting Between
Floor Joist
A. Wall cap
B. 6" (15.2 cm) round wall venting
A. 6" (15.2 cm) round wall venting
B. Wall cap
Option 4 -Venting behind
Cabinet Kick Plate
A. Wall cap
B. 6" (15.2 cm) round wall venting

Concrete Slab Installations -Exhaust Through Wall
B
ANL ¸_!ii__
M_ _
S
E
A. Wall cap
B. 6" (15.2 cm) round metal vent
C. 16" (40.6 cm) maximum
D. 6" (15.2 cm) round PVC sewer pipe
E. 6" (15.2 cm) round metal vent
F. 6" (15.2 cm) round PVC coupling
G. Concrete slab
H. 6" (15.2 cm) round PVC sewer pipe
I. 6" (15.2 cm) round 90°PVC sewer pipe elbow
J. Tightly pack gravel or sand completely around pipe.
K. 3O ft (9.1 m) max.
L. 6" (15.2 cm) round 90°PVC sewer pipe elbow
M. 6" (15.2 cm) round PVC coupling
N. 12" (30.5 cm) minimum
Jenn-Air °Duct Free Filter Accessory Kit
(For model numbers JED3430, JED3536, JED4430, JED4536,
JGD3430 and JGD3536)
On select downdraft models, the Jenn-Air ®Duct Free Filter
Accessory Kit Part Number JDA7000WX is now available. The
Jenn-Air ®Duct Free Filter Accessory Kit is ideal for both new
construction and kitchen renovation projects because it provides
an easy alternative to the installation of metal ducting and venting
in the downdraft system outside the home. The kit includes all
required hardware, one filter and complete installation
instructions. For more information on the Jenn-Air ®Duct Free
Filter Accessory Kit, contact your Jenn-Air dealer or call
1-800-JENNAIR (1-800-536-6247).
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
Vent Piece 6" (15.2 cm) Round
45° elbow 2.5 ft
(0.8m)
6" (15.2 cm) to 31/4'' x 10" 1 ft
(8.3 cm x 25.4 cm) transition (0.3 m)
31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft
to 6" (15.2 cm) 90 ° elbow (1.5 m)
transition
6" (15.2 cm) to 31/4"x 10" 5.0ft
(8.3cmx25.4cm) 90° elbow (1.5m)
transition
31/4'' x 10" (8.3 cm x 25.4 cm 5.0 ft
90° elbow (1.5 m)
31/4"x 10" (8.3 cm x 25.4 cm 12.0 ft
flat elbow (3.7 m)
31/4"x 10" (8.3 cm x 25.4 cm 0.0 ft
wall cap (0.0 m)
Example vent system
90 ° elbow
]- 90 ° elbow
8 ft (2.4 m) straight
1 - wall cap
System length
6ff (I.8 m)
= 5 ft (1.5 m)
= 8 ft (2.4 m)
= 0 ft (0 m)
= 13 ft (3.9 m)
wall cap
NOTE: Flexible vent is not recommended. Flexible vent creates
back pressure and air turbulence that greatly reduce
performance.
90° elbow 5.0 ft
(1.5m)
6" (15.2 cm) 0.0 ft
wall cap (0.0 m)
31/4'' x 10" (8.3 cm x 25.4 cm) 4.5 ft
to 6" (15.2 cm) transition (1.4 m)
6

Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge copper wire.
Electrically ground cooktop.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before You Make the Electrical Connection:
To properly installyour cooktop, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
• A 4-wire or 3-wire, single phase, 120/240 volt, 60 Hz., AC
only electrical supply on a separate, 40-amp circuit breaker is
required for both 30" (76.2 cm) and 36" (91.4 cm) models. If a
fused system is used, fuse both sides of the line.
• The cooktop should be connected directly to the junction box
through the flexible metal conduit. The flexible, armored cable
extending from the fuse box or circuit breaker box should be
connected directly to the junction box.
• Locate the junction box to allow as much slack as possible
between the junction box and the cooktop so that the
cooktop can be moved if servicing becomes necessary in the
future.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that the
ground path and wire gauge are in accordance with local codes.
Check with a qualified electrical installer if you are not sure the
cooktop is properly grounded.
Make sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical Code,
ANSI/NFPA 70-latest edition or CSA Standards C22.1-94,
Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest
edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A UL listed or CSA approved conduit connector must be
provided at each end of the power supply cable (at the
cooktop and at the junction box).
If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
INSTALLATIONINSTRUCTIONS
Decide on the final location for the cooktop.
Excessive Weight Hazard
Use two or more people to move and install cooktop.
Failure to do so can result in back or other injury.
3. Remove vent grille.
A
C
1. Open product as instructed on product packaging.
2. Remove shipping materials and tape from cooktop.
A. Vent grille
B. Filter support tray (non-removable)
C. Removable grease filter
D. Ceramic glass top
4. Remove the removable grease filter by lifting the filter out.

5=
6.
7.
8.
9.
1=
2.
3.
Using 2 or more people, remove the cooktop from the carton.
Use foam end caps from the packaging as a work surface for
the floor or countertop.
Using 2 or more people, place the cooktop upside down on
the foam end caps.
Make sure knobs are )ositioned in the open areas of the end
caps.
Avoid placing the cooktop facedown on the control knobs.
Remove foam strip from the package containing literature.
Remove backing from foam strip.
Apply foam strip adhesive-side down around bottom of
cooktop, flush with edge.
NOTE: The foam strip keeps the underside of the cooktop
glass free from debris and helps the cooktop sit flat on
uneven counters.
A. Cooktop base
B. Foam strip
C. Glass
B
To rotate blower:
1. Locate the four plastic plugs in the plenum bypass.
2. Use the pliers to remove the plastic plugs.
IMPORTANT: Do not throw away the plastic plugs. The
plastic plugs must be reinstalled after the blower exhaust
scroll has been rotated.
A. Blower motor
B. Exhaust scroll
C. Plenum
D. Blower bypass
E. Plastic plugs (4)
3. Insert the 3/8"socket and extension into the hole and use the
ratchet handle to loosen the nut half of a rotation. Repeat this
process for each of the four nuts.
4. With the nuts loosened, the blower exhaust scroll can be
easily rotated downward.
IMPORTANT: The following additional steps must be performed
if the product is being installed in peninsula or island cabinetry.
The blower exhaust scroll is shipped from the factory set to
exhaust straight out the back of the cabinet through an exterior
wall.
\ %'_D
\A E
A. Blower exhaust scroll
B. 10-32 machine nuts (4)
C. Plenum
D. Motor mounting plate
E. Blower motor
5. Retighten each nut with the 3/8"socket, extension and ratchet.
6. Reinstall the four plastic plugs.
1. Using 2 or more people, place cooktop right side up into the
cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from the cutout to avoid
scratching the countertop.
2. For island or peninsula installations, go to "Rotate Blower -
Optional" section.
3. Connect blower exhaust scroll to ducting.
4. Use vent clamps to secure the ducting to the blower exhaust
scroll.
5. Reinstall removable grease filter.
6. Reinstall vent grille.
8

4-Wire Cable from Home Power Supply to 4-Wire Cable
from Cooktop
_¢ IMPORTANT: Use the 4-wire cable from home power supply in
Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge copper wire.
Electrically ground cooktop.
Failure to follow these instructions can result in death,
fire, or electrical shock.
the U.S. where local codes do not allow grounding through
neutral, New Branch circuit installations (1996 NEC), mobile
homes and recreational vehicles, new construction, and in
Canada. A
E
This cooktop is manufactured with the frame connected to the
bare ground wire. Connect the cooktop cable to the junction box
through the UL listed or CSA approved conduit connector.
1. Disconnect power.
2. Remove junction box cover, if present.
3. Connect the flexible cable conduit from the cooktop to the
junction box using a UL listed or CSA approved conduit
connector.
4. Tighten screws on conduit connector if present.
5. See the "Electrical Connection Options" chart to complete
installation for your type of electrical connection.
Electrical Connection Options
If your home has: And you will be Go to Section:
connecting to:
4-wire A fused 4-Wire Cable from
disconnect or Power Supply
circuit breaker
box
I/2"
A. Cable from home power supply
B. Black wires
C. Bare ground wires
D. 4-wire cable from cooktop
E.Junction box
F. White wires
G. UL listed wire connector
H. Red wires
I. UL listed or CSA approved
conduit connector
1. Connect the 2 black wires together using the UL listed wire
connectors.
2. Connect the 2 red wires together using the UL listed wire
connectors.
3. Connect the 2 white wires together using the UL listed wire
connectors.
4. Connect the green (or bare) ground wire from the cooktop
cable to the green (or bare) ground wire (in the junction box)
using the UL listed wire connectors.
5. Install junction box cover.
3-wire A fused 3-Wire Cable from
disconnect or Power Supply
circuit breaker
box

3-Wire Cable from Home Power Supply to 4-Wire Cable
from Cooktop - U.S. only
IMPORTANT: Use the 3-wire cable from power supply where
local codes permit connecting the frame-ground conductor to
the neutral (white) junction box wire.
AE
F
G
C
D
H
A. Cable from home power supply
B. Red wires
C. White wire and green (or bare)
wire (from cooktop)
D. 4-wire cable from cooktop
E.Junction box
F. White wire
G. UL fisted wire connector
H. Black wires
I. UL fisted or CSA approved
conduit connector
1. Connect the 2 black wires together using the UL listed wire
connectors.
2. Connect the 2 red wires together using the UL listed wire
connectors.
3. Connect the green or bare and white cooktop cable wires to
the white (neutral) wire in the junction box using the UL listed
wire connectors.
4. Install junction box cover.
_o_l_©/_ IDc_ ¸ /_._/_o
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all your tools.
3. Dispose of/recycle all packaging materials.
4. Use a mild solution of liquid household cleaner and warm
water to clean cooktop before use. Dry thoroughly with asoft
cloth. For more information, see the "Cooktop Care" section
of the Use and Care Guide.
5. Read "Cooktop Use" in the cooktop Use and Care Guide.
6. Reconnect power.
7. Use the Flow Tester Card provided with your cooktop to
check the airflow (see card for step-by-step instructions).
NOTE: If the cooktop does not work after turning on the power,
check that a circuit breaker has not tripped or a household fuse
has not blown. See "Troubleshooting" section in the Use and
Care Guide for further information.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide or contact the dealer from whom you purchased
your cooktop.
10