Franke AQUACONTACT AQCT0029 User manual

Installation and operating instructions Istruzioni per il montaggio e l’uso
Notice de montage et de mise en service Montage- en bedrijfsinstructies
Instrucciones de montaje y uso
ZMI_001_2000103801-AQCT0029_#SALL_#AQU_#V1.fm/24.09.13
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982181986
FAR-Best.-Nr.: 2000103801
AQCT0029
EA-Nr.: 7612982181993
FAR-Best.-Nr.: 2000103804
AQCT0030
DE
EN
FR
ES
IT
NL

2
Inhaltsverzeichnis35_01.fm
...................................................................................... 3
Please refer to the graphics in the German Installation and Operating
Instructions.
...................................................................................... 14
Les graphiques sont disponibles dans la notice de montage et de mise
en service allemande.
...................................................................................... 25
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 36
Per le grafiche fare riferimento alle Istruzioni per il montaggio e l’uso in
tedesco.
...................................................................................... 47
De tekeningen kunt u in de Duitse montage- en bedrijfsinstructies
vinden.
EN
FR
ES
IT
NL

3
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
0English
AQUACONTACT - shower panel made of solid surface material, 6 V DC
7612982181986
7612982181993 ......... with tray for shower gel
Please refer to the graphics in the German installation and operating instructions.
0Table of contents
1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Properties of MIRANIT-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly, function and commissioning
11. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13. Adjusting the flow time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
14. Adjusting the range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
15. Hygiene flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
16. Thermal disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
17. Adjusting the cleaning switch-off . . . . . . . . . . . . . . . . . . . . . . . . . 10
18. Setting the jet angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance
19. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
20. Maintenance information for MIRANIT-S . . . . . . . . . . . . . . . . . . . 11
21. Replacing a filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
22. Flow quantity regulator Exchanging the flow quantity regulator . . 12
23. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
24. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EN

4
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
1. Abbreviations and units
2. Key
Warning!
Failure to observe can result in bodily injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimal handling of the product.
3. Warranty
Liability is accepted in accordance with the General Terms and Conditions of
Business and Supply.
Use original spare parts only!
DN Nominal diameter in mm
RCD Residual current protective device,
earth leakage circuit breaker
SELV Safety extra low voltage
EA-Nr. International article number
FAR-Best.-Nr. Franke Aquarotter order number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
4. Important notes
• Installation, commissioning and maintenance are to be performed only by a
qualified expert in accordance with the provided instructions, legal requirements,
and the recognised engineering standards.
• All technical connection regulations specified by the local water and electricity
supply companies must be observed.
• The battery compartment with battery or power supply with extension cable must
be ordered separately (see Accessories, chapter 24).
• We reserve the right to make changes.
5. Application
AQUACONTACT - shower panel made of MIRANIT-S solid-surface material for wall
mounting with electronic time control for battery or mains operation. For connection
to premixed hot water or cold water.
30-second flow time.
With integrated hygiene flush (24h after last actuation, for 10s). Functions which can
be activated via reflection code on sensor: Activation/deactivation of hygiene flush
and cleaning switch-off (3 min.).
Additional functions via optional remote control
– Setting the flow and interval times
– Switch from time control to body reflection, maximum flow time of 300 seconds
– Program-controlled thermal disinfection with safety switch-off
6. Technical specifications
Minimum flow pressure: 1.5 bar
Recommended flow pressure: 1,5-5 bar
Maximum operating pressure: 10 bar
Calculation of flow rate: 0.20 l/s
Operating voltage: 6 V DC
Power consumption: 1.5 W
Protection class: IP 67

6
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
7. Properties of MIRANIT-S
MIRANIT-S resin-bound solid-surface material is a mixture of aluminium trihydrate,
natural stone, high quality unsaturated polyester resin and colour pigments.
MIRANIT-S ensures high stability and breaking resistance.
The smooth, non-porous and semi gloss surface is very easy to clean and fulfils the
most stringent hygiene requirements.
8. Scope of delivery
9. Dimensions
10. Installation example
11. Assembly
Warning!
Only operate the fitting with the specified filters.
Failure to observe this instruction can result in an increased germ load in the
drinking water and thus pose a health or mortality risk.
Warning!
• Operate the product only with safety extra low voltage (SELV). The components
do not have to be earthed.
• Secure the mains power supply with a residual current circuit breaker (RCD).
Failure to observe this instruction can result in death or material damage due to
electric shock or fire, for example.
Quantity Name
1 Shower panel with:
AQUACONTACT sensor, solenoid valve cartridge, lockable
water quantity regulators, connection hoses and München
shower head
2 Connection bracket
1 Suspension rail
1 0.15 l/s flow rate regulator
3 Screws, wall plugs
1 Installation and operating instructions

7
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall plugs may have to be used
(to be provided by the customer).
Fig. A: Water connection from above
Fig. B: Water connection from rear
11.1 Only for water connection from the rear: Install the connection bracket (a) leak-tight.
11.2 Screw in the water volume regulator (b) leak-tight.
11.3 Align the water volume regulator so that the locking screw and operating element
are freely accessible.
11.4 For a shower head height of 2.10 m to 2.30 m, mark drill holes for installation at
a height (c) of 2.12 m to 2.32 m from the upper edge of the finished floor.
11.5 Drill holes in accordance with these markings.
11.6 Insert the wall plugs.
11.7 Screw on the suspension rail.
11.8 Suspend the shower panel.
11.9 Mark the remaining drill hole.
11.10 Remove the shower panel.
11.11 Drill holes in accordance with the markings.
11.12 Insert the wall plugs
☞The battery compartment or power supply and extension cable are not part of the
scope of delivery (see Accessories, chapter 24).
☞If you are using a wall-mounted power supply unit, it must be installed around 3 m
away from the shower.
11.13 Connect the AQUACONTACT sensor (f) to
– a battery compartment (d)
or
– a wall-mounted power supply unit (e).
☞If the battery charge state is low, the LED flashes in a 20s cycle.
11.14 Only for water connection from the rear: Prioritise work steps 11.16 to 11.18.
11.15 Mount the shower panel on the suspension rail and screw tight.
11.16 Establish the water connections.
11.17 Open the water volume regulators using a hexagonal wrench.
g: closed
h: open
11.18 Check the water connections for leaks.

8
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
12. Function
☞You can switch between time control and body reflection using the remote control
(not in the scope of delivery; see Accessories, chapter 24)
Time control
Triggering the flow of water
12.1 Hold your hand near the sensor.
• The water will flow.
• The water stops automatically following the set flow time or if you place your hand
near the sensor again.
☞The flow duration is factory-set to 30 seconds.
Body reflection
Triggering the flow of water
12.2 Hold your hand near the sensor.
• The water will flow.
• The water stops automatically once you leave the range of the sensor or after
5 minutes, at the latest.
13. Adjusting the flow time
You can adjust the flow time in increments of 10 seconds from 10 to 60 seconds
using the remote control (not part of the scope of delivery; see Accessories,
chapter 24).
14. Adjusting the range
You can adjust the range for body reflection using the remote control (not part of the
scope of delivery; see Accessories, chapter 24).
15. Hygiene flush
☞At the factory, the hygiene flush function is set so that water flows for 10 seconds
after 24 hours.
You can adjust the hygiene flush parameters using the remote control (not part of the
scope of delivery; see Accessories, chapter 24).
You can choose an interval of 0, 8, 24, 48, or 72 hours for the hygiene flush function
(0 = hygiene flush deactivated). You can adjust the flow time in 10 second
increments from 10 to 60 seconds.

9
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
Display of hygiene flush on fitting
15.1 Hold your hand around 10 cm from the sensor for 3 seconds.
15.2 Between the 1st and 2nd flashing of the LED, remove your hand from the sensor.
• Hygiene flush active: The LED flashes quickly 4 times.
• Hygiene flush inactive: The LED flashes slowly twice.
Activation/deactivation of hygiene flush on the fitting
15.3 Hold your hand around 10 cm from the sensor for 3 seconds.
15.4 Between the 6th and 8th flashing of the LED, remove your hand from the range of
the sensor.
• The LED does not flash.
15.5 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.
15.6 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The LED flashes quickly 4 times. The hygiene flush is active.
or
• The LED flashes slowly twice. The hygiene flush is deactivated.
16. Thermal disinfection
This fitting offers thermal disinfection to reduce the risk of a legionella infection.
Warning!
Personal protective measures (scald protection) must be implemented for the
duration of the thermal disinfection. This might include cordoning off the shower
facilities.
Failure to observe this instruction can result in injuries due to scalding.
The operator is responsible for the execution, monitoring, and logging (room,
tapping point, date, time, temperature and duration).
The manufacturer does not accept any liability for claims by third parties relating
to the improper execution of thermal disinfection on the part of the operator.
☞At the factory, the thermal disinfection function is set so that the fitting cools down for
1 minute after a 5 minute application time.
☞Thermal disinfection can only be triggered using the remote control.
You can adjust the thermal disinfection parameters using the remote control (not part
of the scope of delivery; see Accessories, chapter 24).
An application time of 3, 5, 10, 15, or 20 minutes can be chosen for the thermal
disinfection process. During the application time, water flows without interruption for
2 minutes; the water then flows in pulses until the end of the application time (water
and energy saving function). The cooling time can be set to 0, 1, 3, 5, or 10 minutes.

10
ZMI_001_2000103801-AQCT0029_#SEN_#AQU_#V1.fm
17. Adjusting the cleaning switch-off
You can activate the cleaning switch-off with the remote control (not part of the
scope of delivery, see Accessories, chapter 24) or directly on the fitting.
Cleaning switch-off on the fitting
17.1 Hold your hand around 10 cm from the sensor for 3 seconds.
17.2 Between the 3rd and 5th flashing of the LED, remove your hand from the range
of the sensor.
• The LED does not flash.
17.3 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.
17.4 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The fitting will be switched off for 3 minutes.
• The LED flashes in a 10 second cycle.
☞If you hold your hand around 10 cm from the sensor for at least 3 seconds, the fitting
will be reactivated before the 3 minutes has expired.
18. Setting the jet angle
18.1 Use a face spanner to loosen the retaining ring.
18.2 Set the desired shower range.
18.3 Use a face spanner to fasten the retaining ring.
19. Maintenance and care
The fitting must be checked and maintained at regular intervals depending on the
water quality and in accordance with the local conditions, and rules and regulations
applicable at the site.
Maintain the following components:
• Filters (see chapter 21.)
Use suitable cleaning agents which are not harmful to the fitting in a proper manner
and rinse with water after use. High-pressure cleaners must not be used for
cleaning.