Franke SANX600 User manual

3. Dimensions
Mounting Instructions and Manual
EA-Nr.: 7612979002355 –SANX600 (1000x1000x1205mm)
2. Scope of supply
Qty Part Designation
1 SANX600 6 Person Circular Washtrough Manual Taps
1 SANX605 6 Person Circular Washtrough Manual Taps with Soap Dispensers
1 B4198 1 ½” S Tubular Trap
6 AQUA205 Aqualine S Taps
1 B1353 M5 Allen Key Security Pin
3 SD80 Soap Dispensers (For SANX605 Variant)
1. Important Notes
B1080 –SANX600/605/26.10.2010 1
EA-Nr.: 7612979002362 –SANX605 (1000x1000x1290mm) with SD
SANX600 SANX605
. Before installation, the instructions have to be read and understood.
. Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.

4.Main Body Access and fitting Instructions
Tap Column Access Panel
(1) The Access Panel on the Top of the
Tap Column can be removed by using
the Allen key provided on the 6
security headed bolts.
(2) On the removal of this panel you will
have access to the rear of the taps.
Whereby you can service or change
either the hoses or Taps when
required.
To Service/Refill the Soap Dispenser units.
B1080 –SANX600/605/26.10.2010 2
Warning:
Industrial hand cleaner, natural (organic) fluid soaps
and
cleaners with a high amount of concentrated
components can cause a
rapid abrasion oft he pump mechanism.
Global guidelines for fluid soaps:
pH: 6 - 7,5
Perfume: < 1% (EDTA, NTA) <-
Herbal Oils: < 1% Optimal
Animal Fat: < 1% Viscosity: 1.000 ± 1000mPa.s
For repair/maintenance please refer to SD80
service manual (Included)
Refill bottle:
Remove pump as shown in picture
1- Open hexagon socket with Allen key. Half way
round should be enough.
2- Remove pump set by lifting it.
3- Fill bottle maximum to bottom edge of thread.
4- Fix pump set again. Push until locking sound is
heard.
5- Tighten hexagon socket carefully.
The hexagon socket is a kind of security screw to
prevent removal of the pump by unauthorized
persons.
Soap:
This dispenser is suitable for standard liquid hand
cleaners and creme soaps.
Preferably use mild, biodegradable synthetic
agents.
Do not use cleaners with abrasive or disinfectant.
Main Body
(1) Securely fix the Top support bracket to the mounting wall. Approx recommended
height of between 1700-1780mm from the floor.
(2) Mount the Main body on the bracket and mark the position of the 2 lower fixing
hole points. Remove the main body to create 2 more fixing positions and return Main
body onto the bracket and secure in place.
(3) To mount the Paper Towel and Soap dispenser to the Main body, align the
corresponding holes and use the six fixing positions with the screws provided.
(4) To Secure the basin to the lower part of the Main body, use the six fixing positions
with the screws provided. Make sure that the waste plumbing has been completed
before the lower basin cover is secured in place with the security screws. Use clear
Sanitary Sealant to seal the rear gap between the basin and main body to create a
seamless gap free join.
(5) Secure the Water Spout and Infra Red sensor to the removable service panel and
connect them to the corresponding solenoid valve and power supply. (Flexible hose
required for water spout). Fix to the main body using the six fixing positions with the
security screws provided.
Main Body
(1) The lower larger Access Panel can
be removed by using the Allen Key
provided on the 10 security
headed bolts.
(2) On the removal of this panel you
will have access to the internal
copper pipe work and manifold.
As well and the waste and Trap.
Whereby you can service or
change either the hoses or Trap
when required.
(3) The manifold has a 22.0mm push
fit connector as its base to enable
the installer to connect their pipe
work to.

5. Tap flow time alteration Instructions
Important !
Before installing, flush the pipes in compliance with DIN 1988
To Connect the water Supply.
(1) Insert the Solenoid valve with the seals and check the direction of flow.
(2) Guide the sensor module (g) through the cut-out in the front service panel.
Note that the groove for the anti twist feature must face upwards. When the sensor is
connected, the LED flashes at the Top. (Grub screw at the Top)
Slide the disc onto the sensor module and use the nut to fasten the sensor module.
(3) Use the adaptor cable (k) and extension (h) to connect the solenoid valve (i) and the
sensor module (g).
(4) Connect the Connecting line (l) to the systems power supply.
(5) Connect the system line to the power supply.
(6) Connect the spout to the service panel. Using a flexible hose connect the end of the
spout to the solenoid valve. (Again check the direction of flow)
Secure service panel in place once Infra Red Sensor and Spout are fully connected.
Warning!
.Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided.
.Operate the product only with safety extra low voltage (SELV). Do not earth the
components.
.The power supply must be set up outside of the wet area.
.Secure the electric connection with an earth leakage circuit breaker (RCD).
Failure to observe can mean risk of death or material damage, e.g. from electrical
shock or fire.
B1080 –SANX600/605/26.10.2010 3
8. Hotline
Franke Sissons Ltd.
Carrwood Rd
Sheepbridge
Chesterfield S419QB
T: [phone]
F: [phone]
E: [email protected]
GBR Technical data
Minimum flow pressure 1,0 Maximum operating pressure 10 bar
Recommended flow pressure 3 bar Flow duration 1 - 15 s adjustable
The Premixed water supply should be a minimum 22mm Dia when entering the
pedestal. It is recommended to connect a Thermostatic mixing valve before
connecting to the units manifold framework. For satisfactory operation, a
supply pressure of between 3 –7 bar is required for entering the wash fountain
pedestal. With recommended flow rate of 36 l/min
For pressures in excess of 7 bar g. a flow control or pressure reducing valve
should be fitted (Not supplied)
To adjust the flow time of the Taps:
For further repair/maintenance please refer to the taps service manual (Included)
7. Securing Wash trough to the floor
Please note that the base of the unit has 6 Dia 10.0mm holes that are positioned
uniformly around its base section. These should be used to secure the unit to the floor.
Use fixings which are appropriate to the type of flooring you are securing the unit to.
(Note: Floor fixings are not supplied)
Important !
Before installing, flush the pipes in
compliance with DIN 1988
To Connect Pre mixed water Supply.
Insert a length of 22.0mm copper tube into the
push fit connector at the base of the Manifold
assembly .
(Copper tube not supplied).
(TMV3 Valve not supplied as standard).