Franke FTU 3807 I XS 77H User manual

HANDBOOK HOOD FTU 3807 I XS 77H 9925289 110.0018.185
UPDATED JANUARY 2010
4 SPEED + INTENSIVE
ELECTRONIC PUSH- BUTTONS 4 SPEED + INTENSIVE+ DELAY TIMER+ TO SET UP THE MOTOR
TO A SUCTION SPEED AT 100 M3/H LASTING 10 MINUTES EVERY HOUR+ TURNS LIGHT ON AND
OFF AT REDUCED INTENSITY.
M3/H800 -
DBA 67 -
W 370 -
2 HALOGEN LAMPS X 20 W = TOTAL POWER 40 W

Key Function Display
A Switches the extractor motor on and off at the
latest selected speed Indicates the selected speed.
B Decreases the suction speed.
C Increases the suction speed.
D By pressing this key it is possible to activate the
intensive speed from any previously selected
speed. The intensive speed can be activated even
when the motor is OFF. This speed has been
timed at 10 minutes. After that time the system
activates automatically the latest selected speed.
This function is suitable for cooking conditions
when vapours and smells are of the utmost
emission.
HI appears. The spot down on the right side flashes
once a second.
E By pressing this key it is possible to set up the
motor to a suction speed at 100 m3/h lasting 10
minutes every hour. After this the motor switches
off automatically. When the filter saturation is
going on it is possible to reset the alarm by
pressing this key for about 3 seconds. The
indication is visible only when the motor is off.
Indicates the 24-function. The spot down on the right
side flashes and the motor is on.
Once the process is finished the previous indication
disappears:
FF Indicates that the metal grease filters
saturation alarm has been triggered, and the filters
need to be washed. The alarm is triggered after 100
working hours.
EF Indicates that the charcoal filter saturation
alarm has been triggered, and the filter has to be
replaced; the metal grease filters must also be
washed. The charcoal filter is triggered after 200
working hours.
F By pressing this key it is possible to set the
delayed shutdown of the appliance to 30 minutes.
This function is suitable for a complete elimination
of the residual smells. It can be activated at any
position, and it is deactivated by pressing the key
again or by switching off the motor.
Indicates alternately the selected speed of the hood
and the time left before the hood shutdown. The
spot down on the right side flashes.
G Turns light on and off.
H Turns light on and off at reduced intensity.

Metal grease filters
Filters can be washed in the dish machine. They need to be washed when FF-sign appears on the display or in any
case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset
• Switch off the hood and the lights. If the 24h-function has been activated this has to be deactivated.
• Press the E-key till the display is unlit. Cleaning the filters
• Pull the comfort panels to open them.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling
downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make
sure that they are completely dry. (The colour of the filter sur-face may change throughout the time but this has no
influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing
outwards.
Charcoal filter (recycling version)
This filter cannot be washed or regenerated. It must be replaced when the EF appears on the display or at least once
every 4 months. Activation of the alarm signal
• In the recycling version hoods the filter saturation alarm must be activated during the installation or later.
• Switch off the hood and the lights.
• Disconnect the hood from the mains supply.
• When restoring the connection press and hold B-key.
• When releasing the key two rotating rectangles appear on the display.
• Within 3 seconds press the B-key until a flashing confirmation appears on the dispaly:
• 2 flashes with EF - charcoal filter saturation alarm ACTIVATED
• 1 flash with EF - charcoal filter saturation alarm DEACTIVATED.
REPLACING THE CHARCOAL FILTER Reset of the alarm signal
• Switch off the hood and the lighting. If the 24h-function has been activated this has to be deactivated.
• Press the E-key until the display is unlit. Replacing of the filter
• Open the comfort panels pulling them downwards.
• Remove the metal grease filters.
• Remove the saturated charcoal filter by releasing the fixing hooks
• Fit the new filter and fasten it in its correct position.

LIGHTING
20 W halogen light.
• Remove the 2 screws fixing
the Lighting support, and pull
it out of from the Hood.
• Extract the lamp from the
Support.
• Replace with another of the
same type, making sure that
the two pins are properly
inserted in the lamp holder
socket holes.
• Replace the Support, fixing
it in place with the two screws
removed as above.

PREPARATION OF THE FRAME FOR THE HOOD IN RE-CYCLING VERSION
In case the hood is used in recycling version it is necessary to prepare the frame with all the
necessary connection pieces. In order to make the installation easier it is necessary to
lengthen the frame:
• Unscrew the two screws fixing the upper chimney to the frame and pull the chimney out.
• Unscrew the four safety screws placed at the top in the frame separation area. (A).
• Unscrew the eight metric screws connecting the two columns, placed on both sides of the
frame (B). Installation of components in recycling version:
• Fix the recycling air outlet piece 15 to the upper part of the frame using four 12c screws
supplied with the hood.
• Fix the flange (ø120) 10 to the lower part of the recy-cling air outlet 15.
• Put the reducer flange 9 on the hood body outlet.
• At this point, join the flanges with a pipe. In order to calculate the height of the pipe it is
necessary to es-timate the height of the hood (mm) and subtract 615 mm. (H pipe = H hood-
615).
• Lengthen the frame so that the pipe can be inserted. Place the pipe between the two flanges
and block it. Make sure that the height of the frame is correct considering the height of the
cooker hood (H frame = H hood – 184). Adjust the height of the frame and tighten again the
earlier removed screws. Tighten again the safety screws in order to give more stability to the
structure.
• Fix the pipe with the pipe clamps 25 supplied with the hood
FIXING THE FRAME

• Lift the frame up, making sure that the index over the frame plate is turned forwards.
• Fit the frame slots onto the two screws inserted in the ceiling as above, and turn until reaching the centre of the adjustment slot.
• Tighten the two screws and fasten the other two screws provided; before locking the screws completely, it is possible to adjust the
frame by turning it, making sure that the screws do not come out of their housing in the adjustment slot.
• The Frame must be securely fastened so as to support both the weight of the Hood and the stress caused by occasional axial
pressure against the fitted Appliance. After fixing, make sure that the base is stable even when the Frame is subjected to lat-eral
stress.
• If the Ceiling is not strong enough in the area where the hood is to be fixed, the Installer must strengthen the area using suit-able
plates and counterplates anchored to resistant structures.
Ducted version air exhaust system Connection
When installing the ducted version, connect the hood to the chimney using either a flexible or
rigid pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body
outlet.
• Fix the pipe using the pipe clamps 25 provided.
• Remove any activated charcoal filters.

Installing of the chimney and fixing of the hood
When the hood is installed in recycling version the chimney has to be positioned with the slots upwards.
When the hood is installed in ducting version it has to be positioned in the opposite way.
• Place the chimney on the frame and fix it to the upper part of it with the earlier removed screws. When
installing the hood in recycling version make sure that the slots correspond to the air outlet of the recycling
air outlet piece 15.
• Open the lighting unit by slightly pulling the notch. Remove the unit from the hood by sliding the fixing pivot.
• Remove the filter pushing it towards the back side of the hood unit and simultaneously pulling downwards.
• Remove possible charcoal filters.
• In order to fix the hood body to the frame insert the 4 screws 12f in their seats. It is necessary to leave at
least 4-5 mm gap between the screw heads and the frame plate.
• Hook the hood canopy to the frame and turn it to the left until it reaches the stop, then lock the screws
immediately to prevent he hood canopy from falling out accidentally.
Electrical connection
• Connect to hood to the mains supply through a double pole switch with at least 3 mm clearance between
the contacts.
• Make sure that the connecting piece of the cable is correctly put in the socket.
• Connect the Cmd-connectors of the controls.
• Connect the Lux-connectors of the lighting system.
• In the recycling hood put the charcoal filter in its place.
• Put the metal grease filter and the confort panel into their proper seats

Position Spare part
code fun number description quantity date in
2 1960200 133.0016.959 SPIGOT 120-150 1 9925289
8 1961142 133.0041.779 TOP FILTERING BENT CHIMNEY X 1 9925289
10 1961143 133.0036.538 LOWER CHIMNEY X D370 F770 1 9925289
12 1960325 133.0017.598 SELF-SUPPORTING FILTER 1 9925289
18 1960084 133.0017.669 BRILLIANT LINE SPOT LIGHT PRO 20W 2 9925289
21 1960905 133.0021.010 PANNEL 1 9925289
27 9925204 112.0016.756 CHARCOAL FILTER/ PANEL 1 9925289
30 1961385 133.0017.004 PIVOT STOPPER NR 02 PIECES 1 9925289
32 1960326 133.0017.597 SPOT LIGHTS SUPPORT HINGE WITH PIN 1 9925289
34 1960309 133.0036.314 CLIP 1 9925289
35 1960906 133.0069.905 GLASS FTU3807IXS ISLAND HOOD 1 9925289
36 1960908 133.0017.779 GLASS SUPPORT FTU NO 2 LAMPS 1 9925289
38 1960972 SCREW FTU 3 9925289
38 1960971 FIXING FTU 3 9925289
39 1960902 133.0021.012 LIGHTING COVER 2 9925289
47 1961144 FLANGE D120 H30 (V2) 1 9925289
101 1960649 133.0017.063 CONTROL W 2T T S.HANSA 1 9925289