Franke KEP AC-EBF Series User manual

11/16 2030003743 1
DRINKING FOUNTAIN INSTALLATION
For All KEP( )AC(SL)-EBF Series Combination Drinking Fountains
with Electronic Sports Bottle Filler
This HANDS-FREE BOTTLE FILLER (KEPWEBF) is an extension
of the Franke drinking fountains product line that mounts
directly above our Universal Drinking Fountain.
The wall requires a standard 2-outlet electrical receptacle to
accommodate the electrical cords from both the fountain and
the bottle filler. Otherwise, a grounded plug-in outlet adapter
will be required.
If installed onto a refrigerated drinking fountain, chilled water
can be dispensed through the Bottle Filler. Otherwise, room
temperature water will be dispensed.
The Bottle Filler is shipped partially assembled.
If you ordered the Bottle Filler as a combination with a Drink-
ing Fountain, the drinking fountain is plumbed and ready to
attach to the bottle filler.
WHEN COMPLETED, THE FINISHED ASSEMBLY WILL LOOK LIKE THIS:
Shown here with the Sandstone cabinet finish

11/16 2030003743 2
* On split level models, the Bottle Filler must be mounted on the low unit in order to meet CSA/ADA guidelines
DRINKING FOUNTAIN ROUGH-IN
For All Universal Split Level KEP( )AC(SL)-EBF Series Drinking Fountains
with Electronic Bottle Filler
NOTES:
TRAP, STOP VALVE AND ELECTRICAL OUTLET NOT FURNISHED. ALLOW 4 INCHES [102 MM] MIN. PER SIDE FOR VENTILATION. RECOMMENDED ADULT BARRIER FREE HEIGHT INSTALLATION SHOWN. REDUCE HEIGHT BY 3 INCHES FOR INSTALLATIONS USED PRIMARILY BY CHILDREN AGES 12 AND YOUNGER. UNIT SHALL ALSO HAVE A MINIMUM CLEAR FLOOR SPACE 30 [760] BY 48 [1220]. ADJUST VERTICAL DIMENSIONS AS REQ’D TO COMPLY WITH PROVINCIAL AND LOCAL CODES.
1. 2. 3.
*
115v GROUNDED NORTH AMERICAN DUPLEX RECEPTACLE REQUIRED. THIS DRINKING WATER COOLER IS INTENDED TO BE CONNECTED TO A 20A MINIMUM GROUND FAULT CIRCUIT INTERRUPTING (GFCI) DEVICE TO MEET UL REQUIREMENTS.
4. 5. ALL DIMENSIONS ARE IN INCHES.
DIMENSIONS IN BRACKETS [ ] ARE IN MILLIMETERS.
ROUGHING-IN
AND
DIMENSIONAL DRAWING

11/16 2030003743 3
17 5/8 [447]
16 9/32 [413]
18 5/8
[472]
PUSH PADS
7/16 [11]
1/2 [13]
16 1/32
[407]
7/16 [11]
1 1/4 IPS WASTE
OPTIMUM LOCATION
STUB OUT 1[25] INCH
33 3/8
[848]
*29 5/16
[745] 21 1/4
[539]
18 1/16
[459]
17
[432]
16 1/2
[419]
15 7/18 [392]
12 3/4 [324]
1/2 [10]
7 [8]
4 [99]
5 1/4
[133]
ELECTRICAL
OUTLET OPTIMUM
LOCATION
AIR
FLOW 13 7/8
[352]
48
[1218] 51
[1297]
*27
[687]
1 1/4 O.D.
TAILPIECE
3/8 O.D.
WATER INLET
WITH STRAINER
BOTTLE FILLER
BUTTON
7/8 [22]
THIRD ANGLE PROJECTION ROUGH-IN
AND
DIMENSIONAL DRAWING
NOTES:
1. TRAP, STOP VALVE AND ELECTRICAL OUTLET NOT FURNISHED.
2. ALLOW 4 INCHES [102 MM] MIN. PER SIDE FOR VENTILATON.
* 3. RECOMMENDED ADULT BARRIER FREE HEIGHT INSTALLATION
SHOWN. REDUCE HEIGHT BY 3 INCHES FOR INSTALLATIONS USED
PRIMARILY BY CHILDREN AGES 12 AND YOUNGER. UNIT SHALL ALSO
HAVE A MINIMUM CLEAR FLOOR SPACE 30[760] BY 48[1220]. ADJUST
VERTICAL DIMENSIONS AS REQ’D TO COMPLY WITH PROVINCIAL
AND LOCAL CODES.
4. ALL DIMENSIONS ARE IN INCHES. DIMENSIONS IN BRACKETS [ ] ARE
IN MILLIMETERS.
DRINKING FOUNTAIN ROUGH-IN
For All Universal Split Level KEP( )AC(SL)-EBF Series Drinking Fountains
with Electronic Bottle Filler

11/16 2030003743 4
SECTION 1: GETTING STARTED
WHAT’S INCLUDED?
1. Top cap
2. 38" of 1/4 OD plastic tubing with 19" of sponge tubing insulation
3. Gasket
4. Quick connect tee fitting (only required on split level models)
5. Installation instructions
6. Drip tray
7. Anti splash grate
8. Anti Splash grate screws (2)
9. Snap bushing
10. Wrap-around cabinet facing
11. Hands-free sports bottle filler
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
NOT PRE-DRILLED/BOTTLE FILLER KIT:
If the unit is not pre-drilled or you purchased a BOTTLE FILLER retrofit KIT,
go to PAGE 5A.
PRE-DRILLED/PLUMBED:
If your unit was purchased pre-drilled and plumbed at the factory as a COMBINATION, go to PAGE 11C.
TOOLS REQUIRED:
- 3/8" pilot drill and either a step drill bit up to 7/8"
diameter that will drill through stainless steel top or 7/8"
diameter punch die (retrofit version only)
- Electric drill
- Small tubing cutter for copper tube
- T15 Torx driver with pin in head vandal tip
- T20 Torx driver with pin in head vandal tip
- 1/4" nut driver
- #2 Phillips screw driver

11/16 2030003743 5
SECTION 2: PRESSURIZING THE COOLING TANK
PRESSURIZED
COOLING TANK
NON-PRESSURIZED
COOLING TANK
Cooling
tank
Water
valve/regulator
Supply
Water
Water
valve/regulator
Supply
Water
Cooling
tank
The water should already be turned OFF and the power DISCONNECTED.
A. NON-PRESSURIZED COOLING TANK
If the cooling tank is non-pressurized, follow these instructions. Otherwise, proceed to SECTION 3.

11/16 2030003743 6
STEP 2
Unplug un-insulated water line from water valve inlet (JG
elbow located left side of water valve facing the front of
the cooler). Set tubing aside (being careful to not con-
taminate the water contact in of the tube).
STEP 3
Unplug tubing from JG elbow leading to cooling tank inlet.
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 1
Unit as it appears with top removed.

11/16 2030003743 7
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 4
Plug un-insulated tubing that was removed in Step 1 into
JG elbow leading to the cooling tank from Step 3.
STEP 5
Unplug tubing that is onnected to the water valve outlet (JG
elbow located on the right side of valve facing the cooler.
STEP 6
Connect tubing from Step 5 to JG elbow on the left side of the
valve.

11/16 2030003743 8
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 7
Unplug JG tubing from the cooling tank outlet. Do not set it down.
STEP 8
Using tubing removed in Step 7, plug into JG elbow on the right
side of the valve. (Be sure to re-route the tubing under existing
tubing installed in Step 5 as shown.
STEP 9
Using tubing that is connected to the JG elbow left side of valve
(done in Step 5, plug the other end to the JG fitting at the top of
the cooling tank.

11/16 2030003743 9
B. RETROFIT or FOUNTAIN/FRAME (PRESSURIZED COOLING TANK)
a) Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
b) Turn OFF water supply to the unit. It might be necessary to remove the front panel to access the water stop valve.
c) Place hole template onto cooler top so it is aligned with the left side of unit and wall. SEE NEXT PAGE FOR TEMPLATE.
d) Mark hole location.
e) Remove top from unit. (Figure 1)
f) Using a step drill bit OR 7/8" punch die, make a 7/8" hole through top. You may want to drill a pilot hole to get these started.
g) Install snap bushing into hole to protect tubing from being cut. (Figure 2)
Mark hole location
Template
Remove top from cooler by
removing six #15 torx head
screws on sides of top.
Figure 1 Figure 2
Drill Install Bushing
SECTION 3: CONNECTING THE WATER LINE
DRINKING FOUNTAIN

11/16 2030003743 10
USE THIS TEMPLATE TO MARK THE HOLE
LOCATION ON COOLER TOP
2 1/8 po
[5.4cm]
FROM
BACK
Mark this center point on the top.
Remove the top from the cooler.
Then drill a 7/8" [2.2cm] hole through
the top at the marked centre point.
ALIGN THIS EDGE WITH LEFT EDGE OF COOLER TOP
3 1/4 po
[8.3cm]
FROM SIDE
PLA CE THIS EDGE AGAINST WALL

11/16 2030003743 11
SECTION 3: CONNECTING THE WATER LINE
DRINKING FOUNTAIN
¼" OD tube to connect
to Bottle Filler
a) First, remove plug from fitting on tank drain. b) Next, insert end of tube into fitting.
c) Feed tubing up through the top and attach the top to the cooler. (Figure 1)
C. CONNECT THE BOTTLE FILLER TUBE
This tube supplies cold water from the cooling tank to the Bottle Filler.
Figure10
Figure 1

11/16 2030003743 12
SECTION 4: MOUNTING THE FRAME TO THE WALL
STEP 1:
Place rubber gasket on top of the cooler so it is centered left/right and against the wall. (Figure 11)
STEP 2:
Set the wall frame onto the gasket. Center it left/right and push it against the wall and mark hole locations for wall fasteners. The gasket will
set the frame at the proper height. (Figure 12)
STEP 3:
Secure frame to the wall with fasteners (not provided). Pull plastic tubing up through the hole in the frame. Use mounting slots that will provide
the proper securing location. Make sure to pull the plastic tubing up through the hole in the frame.
Figure 11 Figure 12
Make sure to pull
the plastic tubing
up through the
hole in the frame. Use mounting
slots that will
provide the proper
securing location.
Bottle filler cabinet
Groove in the gasket
Figure 14
STEP 4:
Slide sponge tubing insulation over water line.
Connect the tubing to the INLET elbow on the
back of the Hands-free Bottle Filler assembly and
flow switch connector into the port on the circuit
board. (Figure 13)
STEP 5:
Set the bottle filler
cabinet into place.
MAKE SURE the cabi-
net fits into the groove
in the rubber gasket
on both sides and
front of the cabinet
wrapper. (Figure 14)
Connect tube
to inlet of the
valve
Plastic tubing
Rear view of Bottle Filler
Sponge tubing
insulation
Insert
connector on
end of flow
switch wire
into port on
circuit board
Figure 13

11/16 2030003743 13
STEP 6:
Attach Bottle Filler assembly to the frame using the four (4) vandal resistant torx screws. Leave the top cap off until after the program is set
for this installation (Figure 15)
Figure 15
Torx screws
Figure 16
Anti-splash
grate screws
(provided)
Anti-splash
grate
Drip tray
SECTION 4: MOUNTING THE FRAME TO THE WALL (cont'd)
STEP 7:
Install the drip tray and anti-splash grate into the al-
cove area and secure with the two (2) stainless steel
Phillips head screws. (Figure 16)
STEP 8:
Connect male tab terminals from bottle filler power
supply to female terminals on power cord. Make sure
male tab is seated inside metal contacts of female
terminal.
STEP 9:
Plug in bottle filler cord. The program should be set
up specific for that installation. See the program
guide on the next page.
STEP 10:
Turn ON water supply and check for leaks. Place a
bottle in the alcove to release any trapped air from
the system. Plug in the power cord and replace the
front panel. (Figure 17)
STEP 11:
If everything works correctly, place the top cap back
on the bottle filler and use the remaining two (2) torx
screws to fasten it in place. Otherwise, calibrate the
sensor per the instructions on the next page.

11/16 2030003743 14
30
27
29
28
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
5
6
4
3
2
1
24
SECTION 5: EXPLODED PARTS BREAKDOWN
ELECTRONIC SPORTS BOTTLE FILLER
Haws is a registered trademark of HAWS Corporation. Elkay and Halsey Taylor are registered trademarks owned or licensed by Elkay Sales Inc.
and/or its parent Elkay Manufacturing Company.
1. 036190-003 Alcove, EBF
2. 027189-008 Bushing, Snap
3. 027189-001 Bushing, Snap
4. 036697-001 Cap, Drip Tray Bottom
5. 036686-001 Cap
6. 038168-001 Cord Assembly, DC Power Supply
7. 036191-002 Drain, Short
8. 036701-001 Drip Tray Assembly - Service
9. 038026-001 Electronics Assembly, IR/LCD
10. 036687-001 Frame
11. 028668-001 Fitting, PP Reducing Union
12. 029199-103 Fitting, PP Union Tee White
13. 036689-001 Gasket
14. 017681-008-SP Insulation, Sponge Tube
15. 038031-002 Label, Alcove Sensor
16. 038031-001 Label, LCD Bezel
17. Label not required for Canada
18. 038027-001 Lens, IR Bottle Filler
19. 031434-017 Nameplate, FRANKE
20. 038032-001 Nozzle Assembly, Flow
21. 038036-003 Power Supply 12VDC
22. 026642-003 Screw, Hex HD Tapping
23. 036049-002 Screw, Flat Head Tapping
24. 031875-003 Screw, Truss HD Tapping
25. 038030-001 Solenoid Valve 12VDC
26. 036688-001 Tray, Drip
27. 036695-001 Tray, Grille Drip
28. 029959-006 Tube, PE White 12"
29. 030152-046-SP Tube, PE White 38"
30. 036691-003 Metal Wrapper
Retrofit Parts:
13. SRH-KEPWSBF Gasket, Sunroc/Haws
13. EKG-KEPWSBF Gasket, Elkay/Halsey Taylor

11/16 2030003743
Franke Kindred Canada Limited
1000 Franke Kindred Road
Midland, ON L4R 4K9
Tel [phone]
Fax [phone]
www.franke-commercial.com
Commercial products
SECTION 6: PROGRAM GUIDE
FOR ELECTRONIC BOTTLE FILLER
Factory default settings are for:
tBO6/'*-5&3&%VOJU
tBTFDPOENBYJNVNSVOUJNF
1. Top cap is set aside until program is complete. Remove top cap by unscrewing two (2) T15 torx
screws, if needed.
2. Reach hand down between frame and front of cabinet to gently press button sticking up from top
of circuit board (Note: Circuit board runs on low voltage and will not shock you). A remote button
is available. Remove wire tie, bundling it inside bottle filler and feed it through hole in cooler top.
You can then adjust program using button through access panel of cooler.
3. To enter program mode, press and hold button for about 3 seconds. When you hear a beep, let go of
button. You are now in Program Mode. Pressing button for an instant will advance to next screen. It will
revert back to Operating Mode if no button is pressed for 10 seconds.
4. When you enter Program Mode, display screen will read “UNFILTERED UNIT.” To access settings for
“FILTERED UNIT”, press and hold button for about 3 seconds. Press button for an instant to advance to
next menu item.
5. If you wish to reset filter life counter or bottle counter, press and hold button for 3 seconds in screen
asking corresponding question.
6. Default capacity for filter life counter is 1250 gallons (to match VERSAFILTER® filter). Press and hold
button 3 seconds in “FILTER CAPACITY OF…” screen to change setting to 3000 gallons (GALAXI® green
filter media - may not be available at time of printing).
7. “Bottle Filler Set_time” screen is to adjust maximum run time once sensor is activated. Water flow will
stop once container is removed from alcove, but this feature ensures very little water is wasted if some-
one tampers with dispenser.
8. Unit is calibrated at factory, but it is recommended that sensor be recalibrated at each install. Also, if
you are having problems with sensing of a bottle, try recalibrating it before calling for service. Press and
hold button for 3 seconds to calibrate sensor in “INFRARED SENSITIVITY” screen.
9. Put top cap back on and fasten in place with two (2) torx screws.
Status / Statut
Ok
Service soon
Service Recommended
D’accord
Service bientôt
Service recommandé
BOTTLES SAVED
BOUTEILLES SAUVÉES

11/16 2030003743 1
Cette REMPLISSEUSE DE BOUTEILLES MAINS LIBRES « KEPWEBF »
est un prolongement de la gamme de fontaines à boire Franke qui se
monte directement sur notre fontaine à boire universelle.
Le branchement des cordons électriques de la fontaine et de la
remplisseuse nécessite une prise murale standard double (2 sorties).
Autrement, il faut prévoir un adaptateur de branchement avec mise à
la terre.
En cas d'installation sur une fontaine à boire réfrigérée, la remplis-
seuse de bouteilles sert de distributeur d'eau réfrigérée. Sinon, l'eau
est à la température de la pièce.
La remplisseuse de bouteilles est livrée partiellement assemblée.
Si vous avez commandé la remplisseuse en combinaison avec une
fontaine à boire, cette dernière est équipée de la plomberie et prête à
raccorder à la remplisseuse.
UNE FOIS L’INSTALLATION TERMINÉE, LA REMPLISSEUSE RESSEMBLE À CECI :
INSTALLATION DE FONTAINE À BOIRE
Pour les fontaines combinées série KEP( )AC(SL)-EBF
avec remplisseuse de bouteilles avec compteur digital
Le modèle illustré se caractérise par le fini d'armoire Sandstone au bas.

11/16 2030003743 2
DESSIN COTÉ ET DE RACCORDEMENT
Pour les fontaines combinées série KEP( )AC(SL)-EBF
avec remplisseuse de bouteilles avec compteur digital
* Sur les modèles à deux niveaux , la bouteille de remplissage doit être monté sur l'unité bas afin de répondre CSA / directives de l'ADA
EMPLACEMENT OPTIMAL DE LA PRISE ÉLECTRIQUE
BOUTON DE REMPLISSEUSE DE BOUTEILLES
PROJECTION AMÉRICAINE
PLAQUES-POUSSOIRS
ARRIVÉE D’EAU DE D.E. 3/8 AVEC FILTRE
ÉVACUATION DE 1 1/4 IPS - EMPLACEMENT OPTIMAL DE LA TUBULURE DE SORTIE À 1 [25] POUCE
REFROIDISSEUR
D'EAU
FONTAINE
D'EAU
PARTIE COURTE
TUYAU DE DRAINAGE
REFROIDISSEUR D'EAU ET FONTAINE
TROUS DE FIXATION 1/4 [6] 8 ENDROITS
ALIMENTATION EN EAU DE 3/8 - EMPLACEMENT OPTIMAL DE LA TUBULURE DE SORTIE À 1 [25]
TROU DE FIXATION DE SUPPORT 1/4 [6], 2 ENDROITS
RACCORDER LA SORTIE ÉLOIGNÉE DU REFROIDISSEUR À L'ENTRÉE DE LA FONTAINE À L'AIDE DU RACCORD FOURNI VIS TORX T15
TROUS DE FIXATION DE SUPPORT 5/16 [8], 4 ENDROITS
2 ENDROITS
2 ENDROITS
ÉCOULEMENT D’AIR
2 ENDROITS
2 ENDROITS
2 ENDROITS
2 ENDROITS
2 ENDROITS
4 [102]
7 [178] 2 ENDROITS
2 ENDROITS
2 ENDROITS
EMBOUT DE D.E. 1 ¼ PO
SOL FINI
MUR FINI
NOTES:
SIPHON, ROBINET D’ARRÊT ET PRISE ÉLECTRIQUE NON FOURNIS. PRÉVOIR 4 POUCES [102 MM] AU MINIMUM DE CHAQUE CÔTÉ POUR LA VENTILATION. INSTALLATION ILLUSTRÉE : ACCÈS FACILE, À UNE HAUTEUR RECOMMANDÉE POUR UN ADULTE. RÉDUIRE LA HAUTEUR D’INSTALLATION DE TROIS (3) POUCES POUR LES ENFANTS DE 12 ANS ET MOINS. PRÉVOIR ÉGALEMENT UNE SURFACE MINIMALE AU PLANCHER DE 30 [760] PAR 48 [1 220] POUR L’INSTALLATION DE L’APPAREIL. ADAPTER LES DIMENSIONS VERTICALES AUX EXIGENCES DES CODES PROVINCIAUX ET LOCAUX.
1. 2. 3.
*
PRISE NORD-AMÉRICAINE DOUBLE AVEC MISE À LA TERRE 115 V NÉCESSAIRE. POUR RESPECTER LES EXIGENCES UL, CETTE FONTAINE À EAU FROIDE DOIT ÊTRE BRANCHÉE À UN CIRCUIT DE 20 A MINIMUM AVEC DISJONCTEUR DIFFÉRENTIEL (GFCI).
4. 5. TOUTES DIMENSIONS EN POUCES.
LES DIMENSIONS ENTRE CROCHETS [ ] SONT EN MILLIMÈTRES.
DESSIN COTÉ
ET DE
RACCORDEMENT

11/16 2030003743 3
DESSIN COTÉ ET DE RACCORDEMENT
Pour les fontaines combinées série KEP( )AC(SL)-EBF
avec remplisseuse de bouteilles avec compteur digital
17 5/8 [447]
16 9/32 [413]
18 5/8
[472]
PLAQUES-POUSSOIRS
7/16 [11]
1/2 [13]
16 1/32
[407]
7/16 [11]
ÉVACUATION DE 1 1/4 IPS -
EMPLACEMENT OPTIMAL DE
LA TUBULURE DE SORTIE
À 1 [25] POUCE
33 3/8
[848]
*29 5/16
[745] 21 1/4
[539]
18 1/16
[459]
17
[432]
16 1/2
[419]
15 7/18 [392]
12 3/4 [324]
1/2 [10]
7 [8]
4 [99]
5 1/4
[133]
EMPLACEMENT
OPTIMAL DE LA PRISE
ÉLECTRIQUE
ÉCOULEMENT
DE L’AIR
13 7/8
[352]
48
[1218] 51
[1297]
*27
[687]
EMBOUT DE
D.E. 1 1/4 PO
ARRIVÉE
D’EAU DE D.E.
3/8 AVEC FILTRE
BOUTON DE REMPLISSEUSE
DE BOUTEILLES
7/8 [22]
PROJECTION AMÉRICAINE DESSIN COTÉ
ET DE
RACCORDEMENT
NOTES :
1. SIPHON, ROBINET D’ARRÊT ET PRISE ÉLECTRIQUE NON FOURNIS.
2. PRÉVOIR 4 POUCES [102 MM] AU MINIMUM DE CHAQUE CÔTÉ POUR
LA VENTILATION.
* 3. INSTALLATION ILLUSTRÉE : ACCÈS FACILE, À UNE HAUTEUR
RECOMMANDÉE POUR UN ADULTE. RÉDUIRE LA HAUTEUR
D’INSTALLATION DE TROIS (3) POUCES POUR LES ENFANTS DE
12 ANS ET MOINS. PRÉVOIR ÉGALEMENT UNE SURFACE MINIMALE
AU PLANCHER DE 30 [760] PAR 48 [1 220] POUR L’INSTALLATION DE
L’APPAREIL. ADAPTER LES DIMENSIONS VERTICALES AUX EXIGENCES
DES CODES PROVINCIAUX ET LOCAUX.
4. TOUTES DIMENSIONS EN POUCES. LES DIMENSIONS ENTRE
CROCHETS [ ] SONT EN MILLIMÈTRES.

11/16 2030003743 4
SECTION 1 : COMMENT DÉMARRER
UNITÉS NON PERCÉES NI ÉQUIPÉES DE LA PLOMBERIE À L'AVANCE :
Si votre unité n'est pas déjà percée ou si vous avez acheté un nécessaire de remplacement de REMPLISSEUSE DE
BOUTEILLES, se reporter à 5 « A » (page suivante).
UNITÉS MUNIES DES PERÇAGES ET ÉQUIPÉES DE LA PLOMBERIE :
Si votre unité a été achetée comme ensemble déjà muni des perçages et équipé de la plomberie en usine, sous la forme d'une
COMBINAISON, se reporter à 11 « C ».
QU’EST-CE QUI EST COMPRIS?
1. Couvercle supérieur
2. 38 po de tuyau en matière plastique de 1/4 po de D.E. et
19 po d’isolant pour tuyauterie en mousse
3. Joint d’étanchéité
4. Té à raccordement rapide
5. Directives d’installation
6. Plateau d’égouttement
7. Grille anti-éclaboussures
8. Vis pour grille anti-éclaboussures (2)
9. Une bague montage par pression
10. Cabinet couvercle de châssis
11. Châssis
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
OUTILS NÉCESSAIRES :
- 3/8 po foret pilote et soit un peu étape de forage jusqu'à 7/8 po
diamètre qui va percer en acier inoxydable haut ou 7/8 po de diamètre
poinçon matrice (version de rénovation seulement)
- Perceuse électrique
- Petit coupe-tube pour tuyaux en cuivre
- Tournevis Torx T15 à pointe à 6 pans anti-vandalisme
- Tournevis Torx T20 à pointe à 6 pans anti-vandalisme
- Tournevis à douille de 1/4 po
- Tournevis à pointe cruciforme n° 2

11/16 2030003743 5
SECTION 2: PRESSURISATION DU RÉSERVOIR DE
REFROIDISSEMENT
L'arrivée d'eau doit déjà être COUPÉE et l'alimentation électrique DÉBRANCHÉE.
A. RÉSERVOIR DE REFROIDISSEMENT NON PRESSURISÉ
Si le réservoir de refroidissement n'est pas pressurisé, suivre ces directives. Autrement, passer à la SECTION 3.
RÉSERVOIR DE REFROIDISSEMENT
NON PRESSURISÉ
Robinet/régulateur
sur l'eau
L'alimentation
en eau
Réservoir de
refroidissement
Robinet/régulateur
sur l'eau
L'alimentation
en eau
Réservoir de
refroidissement
RÉSERVOIR DE REFROIDISSEMENT
PRESSURISÉ