Franklin Electric Little Giant LSE2-W User manual

SOLAR LED
EGGLITE KIT
LSE2-W
ENGLISH
EN
This instruction sheet provides you with the information required to
safely own and operate your product. Retain these instructions for
future reference.
The product you have purchased is of the highest quality
workmanship and material, and has been engineered to give you
long and reliable service. This product has been carefully tested,
inspected, and packaged to ensure safe delivery and operation.
Please examine your item(s) carefully to ensure that no damage
occurred during shipment. If damage has occurred, please contact
the place of purchase. They will assist you in replacement or repair,
if required.
READ THESE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL, OPERATE, OR SERVICE YOUR
PRODUCT.KNOWTHEPRODUCT’SAPPLICATION,LIMITATIONS,
AND POTENTIAL HAZARDS. PROTECT YOURSELF AND
OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE
TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE!
SAFETY GUIDELINES
WARNING
WARNING: Risk of explosion. Do not incinerate.
WARNING: Replace battery with authorized part only. Use of
another battery may present a risk of fire or explosion.
Dispose of used battery promptly. Keep away from children. Do not
disassemble and do not dispose of in fire.
This product has not been investigated for swimming pool or spa
use.
ASSEMBLY
Your Solar LED EggLite kit comes fully assembled with the following
items:
Solar panel with 6-inch cord
Two white LED EggLites
10-foot extension cord with three-way connector
Stake extension
Spare o-ring
If you purchased the above items separately, follow the instructions
below to ensure your unit is correctly assembled. (Skip to step 5 if
you purchased these items as a kit.)
1. To ensure a waterproof connection, place an o-ring onto each
light plug (Figure 1).
2. Insert each of the two light plugs into a three-way connector
receptacle (Figure 2), then tighten the connectors.
IMPORTANT: Align the flat sides on the plugs and the receptacles
for proper polarization. If the plugs are not inserted correctly the
lights will not illuminate.
3. Connect additional lights (sold separately) to the third receptacle
on the three-way connector (Figure 3).
4. Connect one end of the extension cord to the short cord of
the solar panel. Connect the opposite end to the three-way
connector (Figure 3). NOTE: Ensure that the flats are aligned as
previously described.
5. Attach extension to ground stake.
6. Slide the MODE switch to the RUN position (Figure 4). This will
automatically turn the lights off during the day so that the battery
can recharge. It will also turn the lights on during the night
to illuminate your landscape. NOTE: For the automatic on/off
switching to work properly, ensure the photocell (Figure 5) is not
covered and is always exposed to ambient light.
7. Your LED EggLites should now be fully functional. The lights
should turn on with the solar panel in a mostly dark room, and turn
off when the room is well lit.
•
•
•
•
•
1
10’ Low-Voltage Power
Cord
16”
Pliable
Cord
EXTRA LED EGGLITES
COMPLETE SOLAR LED EGGLITE KIT
Solar Panel,Two LED EggLites, and 10’ Low-Voltage
Power Cord
Three-way connector
(up to 6 total)
Figure 3
O-ring
Light plug
Connector
Figure 1
IMPORTANT!
Align flat sides
Three-way connector
receptacle
Light plug
Figure 2
Franklin Electric Co., Inc.
P. O. Box 12010
Oklahoma City, OK 73157-2010
Phone: [phone] • Fax: [phone]
www.LittleGiantPump.com
CustomerService-[email protected]

INSTALLATION AND OPERATION
1. Consider the following to determine the best location for your
solar LED EggLites:
The lights can be used dry or submerged in your water
feature. The solar panel should not be submerged, but can
withstand rainy, outdoor environments.
Each light comes with a 16-inch pliable cord that can be
formed to stand on its own or coiled around foliage and
fountain heads in the landscape.
Choose a location for the solar panel that maximizes its
exposure to the sun. Locate the solar panel so that its
surface is mostly perpendicular to the sun’s rays throughout
the day.
The solar panel can be secured using one of two methods.
1) Ground Stake: Use the attached ground stake to secure
the panel into the ground of the landscape (Figure 6). To
adjust the orientation of the panel to the sun, loosen the
stake screw, pivot the panel to the desired orientation,
then tighten the screw. 2) Frame Mounting: The solar panel
•
•
•
•
2
Figure 4
MODE
switch
RUN
TEST
RUN
TEST
Solar
panel
Figure 5
Photocell
TEST button
(Use only in TEST
mode)
Solar
panel
Figure 6
Mounting slots
Stake screw
Ground stake
Cover screw
(1 of 2)
Mounting slots
Battery cover
frame has slots that accommodate a variety of mounting
methods. Use #6 size wood screws (not included) to
secure the panel to a fixed board or post, or use wire (not
included) to loop through the slots and secure the panel to
a fence or similar item.
An optional extension cord (5- or 10-foot) can be purchased
to provide greater distance between the EggLites and
the three-way connector. See list of accessories (sold
separately).
2. Install the pre-assembled lights and solar panel.
3. Check to see that all LED EggLites illuminate when the ambient
light turns dark.
MAINTENANCE
1. BATTERY: Although your kit’s battery has a long life, it may
eventually need to be replaced. Please follow the instructions
below:
a. Loosen the stake screw at the stake pivot point and rotate the
stake to allow access to the battery cover (Figure 6).
b. Remove the 2 battery screws from the cover.
c. Remove the battery cover.
d. Remove the battery and disconnect the cable.
e. Connect and install the new battery. Use an authorized
replacement battery only (see Replacement Parts table).
f. Replace the battery cover and secure it with the 2 cover
screws.
g. Rotate the stake back to its original position and tighten the
stake screw.
2. PHOTOCELL: For proper operation of the automatic on/off
feature, periodically clean the photocell window using a clean,
damp cloth (Figure 5).
•

3
TROUBLESHOOTING
Symptom Cause Remedy
LED Lites do not illuminate
Mode switch is not in RUN position (Figure 4) Change switch position to RUN
Ambient light is preventing LEDs from illuminating Reduce ambient light or move LED lites to a darker
location.
Connector flats are not properly aligned (Figure 2) Re-connect with proper alignment of flats
Battery is not fully charged Expose solar panel to sun for a day, then retry the
lites
Battery needs replaced Replace battery
Photocell is damaged Replace solar panel
LED Lites are always illuminated
Ambient light to photo cell is blocked Clean transparent cover to photocell to allow ambient
light to penetrate
Photocell is damaged Replace solar panel
REPLACEMENT PARTS
Part No. Description
566430 LSPR solar panel
950785 Replacement battery kit
566440 Extra Mini EggLite, white
166331 Replacement stake kit

4
Form 998675 - 07/22/2010
© 2009 Franklin Electric Co., Inc.
Little Giant® is a registered trademark of Franklin Electric Co., Inc.
LIMITED WARRANTY
Your product is guaranteed to be in perfect condition when it leaves our Factory. No warranty will apply to light bulbs or batteries. Little Giant
Pump Company, Inc. dba Franklin Electric Water Transfer Systems (hereafter “the manufacturer”) warrants all other components against
defective materials and workmanship for a period of 12 months from date of purchase by the user. Any product that should fail for either
of the above two reasons and is still within the warranty period will be repaired or replaced if returned prepaid to our Factory. All defective
products returned under warranty will be fully inspected to determine cause of failure before warranty is approved. The manufacturer will
honor the warranty within the warranty time period specified on satisfactory written proof of purchase.
DISCLAIMER: The foregoing warranty is an exclusive warranty in lieu of any other express warranties. Any implied warranties (including, but
not limited to, any implied warranty of merchantability or fitness for a particular purpose) to the extent either applies to this product shall be
limited in duration to the periods of the express warranties given above.
Warranty will be VOID if any of the following conditions are found:
1. Cord seal damaged or removed.
2. Product connected to voltage other than indicated on nameplate.
3. Cord cut off to a length less than three feet.
4. Product abuse by customer.
Any oral statements about the product made by the seller, the manufacturer, the representatives or any other parties, do not constitute
warranties, shall not be relied upon by the user and are not part of the contract for sale. Seller’s and manufacturer’s only obligation, and
buyer’s only remedy, shall be the replacement and/or repair by the manufacturer of the product as described above. NEITHER SELLER
NOR THE MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, BUT NOT LIMITED TO INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO
PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS), ARISING OUT OF THE USE OR THE INABILITY
TO USE THE PRODUCT AND THE USER AGREES THAT NO OTHER REMEDY SHALL BE AVAILABLE TO IT. Before using, the user shall
determine the suitability of the product for the intended use, and user assumes all risk and liability whatsoever in connection therewith.
Some states and countries do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state and country to country.
For parts or repair, please contact ....................................................... 1-888-572-9933
For technical assistance, please contact ............................................ 1-888-956-0000
Pour des parties ou la réparation, entrez s’il vous plaît en contact ..... 1-888-572-9933
Pour l’aide technique, entrez s’il vous plaît en contact ....................... 1-888-956-0000
Para partes o la reparación, por favor póngase en contacto .............. 1-888-572-9933
Para la ayuda técnica, por favor póngase en contacto ....................... 1-888-956-0000
www.LittleGiantPump.com
CustomerService-[email protected]