Freedom Charge FDMC-1222 User manual

INSTALLATION(INSTRUCTIONS
1222 Instructions 3-9-15.doc Page 1 of 5
2015 - Ford Mustang Qi Wireless Charging Kit
(Kit # FDMC-1222)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
Qi Wireless Charging Module with
Mustang Specific Substrate
Power Harness with 3 amp Fuse
2015 Mustang Specific Non Slip Mat
These Instructions with Template
Removable Consumer Product Label
Plastic Trim Removal Tool
10mm socket driver
7mm Socket Drive
Center Punch/Scribe Tool
Power Drill
1/2” Drill Bit
Wire Ties
Soldering Iron & Solder (Recommended)
Tape or Heat Shrink Electrical Tubing
*Note this product is designed to work with Qi compatible devices. Please confirm that
your device is Qi compatible before installation. Visit www.brandmotion.com for phone
compatibility guide.
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions.
IMPORTANT: Do not place smart keys
within 15cm of charging mat. Vehicle
may not detect key to start vehicle. Do
not place metal objects in tray while
charging.

INSTALLATION(INSTRUCTIONS
1222 Instructions 3-9-15.doc Page 2 of 5
Step 1: Use a plastic trim removal tool to remove
left and right side front console trim.
Step 2: Remove (2) 7mm sockets from the front of
the left and the right side of the console.
Step 3: Remove rubber tray insert from front of
console.
Step 4: Remove (2) 7 mm sockets from under
rubber tray.Removal is not required but it does
help with lifting the top of console.
Step 5: Use a plastic trim removal tool to loosen
the console top trim from inside the armrest.
Step 6: Lift up from rear of console to unclip the
top of console. Ensure the front of console side is
pulled out slightly.

INSTALLATION(INSTRUCTIONS
1222 Instructions 3-9-15.doc Page 3 of 5
Step 7: Unplug (2) harness to the under side of
the top console.
Step 8: Unplug connector to the power outlet
(inside the armrest). Press in tab on top to release.
Step 9: On the power harness included with the
Freedom Charge cut off the ringlet on the black
wire (ground).
Step 10: Splice the wires using military splice or
soldering into the factory harness. (10a.) The red
wire connects to the grey/orange and the black
wire connects to the black/purple wire. Wrap with
electrical tape or heat shrink. (10b)
10a
10b.
Step 11: Remove rubber insert from inside
armrest and remove the (2) 10mm nuts from the
bottom studs.
Step 12: Cut out provided template and mark
location for 1/2” hole.

INSTALLATION(INSTRUCTIONS
1222 Instructions 3-9-15.doc Page 4 of 5
Step 13: Drill 1/2” hole in previous marked
location. Lift up on the console to ensure there is
clearance to drill the hole.
Step 14: Run the power harness that was
connected to the power point into the ½hole that
was just drilled in the step 13.
Step 15: Install non-slip Freedom Charge mat to
wireless charging module. Place the 4 locator pins
in corresponding holes before installing them in the
armrest.
Step 16: Firmly press mat around LED.
Step 17: Connect the Freedom Charge plug to the
power harness that was run to the armrest. Pull as
much excess power harness back into the
underside of the console. Remember to leave a
little to reinstall the (2) 10 mm nuts.
Step 18:Check to ensure the power harness or
factory wiring is not going to be pinched lower than
the console and reinstall the (2) 10mm nuts.

INSTALLATION(INSTRUCTIONS
1222 Instructions 3-9-15.doc Page 5 of 5
Step 19: Insert any of the excess power harness
wire into the ½hole and install the Freedom
Charger into the bottom of the armrest.
Step 20: Test system. LED light will illuminate
blue once accessories are on. Once Qi equipped
device is placed on Freedom Charge LED will
illuminate Green and charging begins.*Please
note on some devices syncing may take up to 15
seconds. Coil locations vary on various devices;
move device on mat until LED illuminates green.
Step 21: Reassemble vehicle. Follow your
disassembly steps in reverse order, taking care not
to bind the harness wiring when reinstalling trim.
Step 22: Place removable consumer product label
on center of mat.
(
(
(
(
(
(
(
(
(
(
(
(
(
(