Frigidaire CPA12EDU111 User manual

FGIDAIRE
=i_ ii
Normal
Accessories Included
www,frigi

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
Power supply cord
with 3-prong grounding
plug and current
detection device
Prevent Accidents
ii ii
ii
ii'
ii,
ii
ii =
•Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet.
o If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the glass first.
•Be sure the air conditioner has been securely and correctly installed according to the
installation instructions in this manual. Save this manual for possible future use in
removing or reinstalling this unit.
Electrical Information
The complete electrical rating of your new protable air conditioner is stated on the serial
plate. Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,
proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a qualified electrician install the proper receptacle.
Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.
DANGER.IAvoid Serious Injury or Death
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area on top of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
• Do not operate the air conditioner with wet hands.
•Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.
02009 Electrolux Home Products, Inc. All rights reserved.

o
o
CAUTION. IAvoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit's installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
Operation of Current
Device
Plug in &
press RESET
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESETbutton pops out.
3. Press the RESET button, Again you will notice a click as the button engages,
4. The power supply cord is now supplying electricity to the unit,
.Do not use this device to turn the unit on or off.
Always make sure the RESETbutton is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
'If power supply cord is damaged, it CANNOT be repaired, It MUST be replaced by one obtained
from the product manufacturer.
02009 Electrolux Home Products, Inc. All rights reserved.

Product Registration Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the side of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Normal Sounds
Sound of l?ushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
High pitched Chatter
Today's high efficiency
compressors may have a
high pitched chatter during
the cooling cycle.
Gurgle/Hiss
"Gurgling or hissing" noise may be
heard due to refrigerant passing
through condenser during normal
operation.
Vibration
Unit may vibrate and make noise
because of uneven floor.
02009 Electrolux Home Products, Inc. All rights reserved.

Unit Description
CONTROL PANEL
CARRYING HANDLE
(BOTH SIDES)
REMOTE CONTROL !
STORAGE DOOR
REMOTE CONTROL
ROOM AIR DISCHARGE
Fig. 1
AIR INTAKE
EXHAUST
AIR OUTLET
DEHUMIDIFYING
DRAIN OUTLET
DUCTED AIR INLET
ADAPTOR A
BOTTOM TRAY DRAIN OUTLET
Accessories Included
PARTS: PARTS NAHE: QUANTITY:
Adaptor A(Unit) 2 pcs
Window Hose Kit(Hose and Adaptor B) 2 set
_J % JJWindow Sliding Kit 1 set
Foam Seal 3 pcs
Remote Control 1 pc
Battery(For remote control) 2 pcs
12.7mm Screw 4 pcs
19mm Screw 2 pcs
12.7mm Hex Head Cap Screw 2 pcs
Safety pc
Lock 1
Fig, 2
•Check all the accessories are included in the package and please refer to the installation
instructions for their usage.
02009 Electrolux Home Products, Inc. All rights reserved. r-

Installation Instructions
HOSES INSTALLATION
In the COOLING Mode the appliance must be placed close to a window or
opening so that the air outside could be ducted inside the unit and the warm
exhaust air can be ducted outside.
First position unit on a flat floor and make sure there's a minimum of 30.5cm
clearance around the unit, and is within the vicinity of a single circuit outlet
power source.
1. Take out the hoses from the package.
2. Remove adaptor A from unit by sliding sideways (Fig. 3).
3. Extend the other end(without adaptor) of the hoses (Fig. 4) and screw
it to adaptor A (Fig. 5).
4. Slide the hose assemblies onto the unit (Fig. 6).
5. Affix the adaptor B into the window slider kit and seal. (Fig. 7&8)
Vertical
window
Window Slider Kit
Minimum :67.5cm(26.6")
Maxmum: 123cm(48.5") Fig. 7
_" Extend the end of hose
Fig, 4
Fig, 5
Horizontal l
window
Window Slider Kit
Minimum:67.5cm(26.6")
Maxmum: 123cm(48.5")
ii
Fig, 8
ide
The hose can be extended from its original length of 38.1cm up to
139.7cm, but it is the best to keep the length to minimum required. Also
make sure that the hose does not have any sharp bends or sags. (Fig. 9)
////
y//,
y//,,
////
//,'1
z///
////
////
////
7//,
////
y//
Fig. 9
02009 Electrolux Home Products, Inc. All rights reserved.

Installation Instructions
(continued)
Installation in adouble-hung sash window
1. Cut the foam seals(adhesive type) to the proper lengths and attach them
to the window and stool. (Fig. 10)
2. Open the window sash and place the window slider kit on the window stool
(Fig. 11). Attach the window slider kit to the window stool. Adjust the length
of the window slider kit according to the width of window. Screw down the
two screws on the window slider kit. See Fig.11. Cut the adjustable window
slider kit if the width of window is less than 67.5cm (Fig. 12).
3. Close the window sash securely against the window slider kit. (Fig. 13)
4. Drive two 12.7 mm screws to secure the window slider kit to the window
sash. (FIG. 13)
5. Securethe window slider kit to the window stool (FIG. 13):
A: Forwooden windows: Use 19mm screws for securing.
B: ForVinyl-Clad windows: Use 12.7mm hex head cap screws for securing.
6. To secure lower sash in place, attach right angle sash lock with
12.7mm (1/2") screw as shown (FIG. 14).
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad
windows, so you can use lock by window itself.
7. Cut the foam seal to an appropriate length and seal the open gap
between the top window sash and outer window sash, as shown in Fig.15.
!2.7mm screws
dowsliderkit
1Y--
hex head cap screws .... \ . p.._
Windowstool rig, 13
Fig. 14
Fig, 15
Installation in asliding sash window
1. Cut the foam seals(adhesive type) to the proper lengths and attach them
to the window frame. See Fig.16.
2. Open the window sash and place the window slider kit on the window stool.
See Fig.17.Attach the window slider kit to the window stool. Adjust the
length of the window slider kit according to the height of window. Screw
down the two screws on the window slider kit. See Fig.17. Cut the adjustable
window slider kit if the height of window is less than 67.5cm (Fig. 12).
3. Close the sliding sash securely against the window slider kit. (Fig. 18)
4. Drive two 12.7mm screws to secure the window slider kit to the window sash.
(Fig. 18)
5. Drive two 19mm screws to securethe window slider kit to the window stool.
(Fig. 18)
6. Cut the foam seal to an appropriate length and seal the open gap
between the sliding sash and outer window sash, as shown in Fig.19.
7.To secure the sliding sash in place, attach right angle sash lock with 12.7mm
(1/2") screw as shown.(Fig.20)
Foamseal
Fig, 19
02009 Electrolux Home Products,Inc.
::____a°dhesev:t t_Pe)
Fig. 10
Windowstool
in_dowsliderkit
Fig. 11
Cut this side to fit your window
...................... : ........................ -- ................................ : ! ;=J
Fig, 12
Foamseal
(adhesive type) _.
Fig. 16
Window stool
6Z5cm_!23cm]_
Window slider kit
Fig. 17
Window stool Window slider kit
19mm screws':,. screws
Fig. 18
All rights reserved.
ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!Jiii!ii

Air Conditioner Features
CONTROL PANEL TURNS UNIT ON OR OFF
CHECK FILTER DISPLAYS REMOTESIGNAL
RESETBUTTON TEMPERATURE/TIME RECEIVER
(
=\auto []
filter / coot m
dry []
fan m u
o]_m mon I heat
timer \_
temp/timer setting
K'F
moc
m Hr
MODE V A FAN SPEED
f f
[-- temp/timer ----J
1
SETS MODE ADJUSTS SETSFAN SPEED
TEMPERATURE
OR TIME
SWING
BUTTON
swmg
Fig, 21
ACTIVATES TIMER
m
s[eep
SLEEP MODE
REMOTE CONTROL
MODE INDICATION \
TEM PERATURE/TIM ER
CONTROL BUTTONS
MODE SELECTOR-
SLEEP BUTTON --
RESET+ LOCK
PIN BUTTONS
_auto fSun
IvI^ i
_[ .... I........I.......F
--! .....I ..... I_......it
• _ •
RESET_ L?K
FRIGIDAIRE
-- FANSPEEDSELECTION
FANSPEEDSELECTOR
-- TIMER BUTTONS
SWING BUTTON
ON/OFF BUTTON
Fig, 22
Battery Size: AAA
Warning: 1. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-
cadmium) batteries.
2. This device complies with Part 15 of the FCCRules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The RESETbutton isdepressed when you want to return to the initial factory settings. The LOCKbutton isdepressed to
lock the keypad so the settings cannot be changed. The key symbol will appear in the display of the remote control,
depress the LOCKbutton again to release. Use a small pin to depress these buttons.
@2009 ElectroluxHome Products, Inc. All rights reserved.

Operating Instructions
The following instructions represent the Control Panel, the same instructions can be used for the Remote Control.
COOLING MODE: In this mode the adaptor hoses MUST be used.
1. Press the MODE button until the "Cool" indicator lights.
2. Press the " V A" Temp buttons for desired setting.
3. Press the FAN button for desired fan speed.
HEATING MODE:
(on some models) In this mode you do not need to use the adaptor hoses. 1. Press the NODE button until the "Heat" indicator lights.
2. Press the " V A" Temp buttons for the desired heat setting.
DRY MODE: In this mode you do not need to use the adaptor hoses, BUT the water
collected must be discharged. See Drainage Section.
1. Press the NODE button until the "Dry" indicator lights.
2. The fan will run at low speed and the display will show the room temperature.
3. Keep doors &: windows closed for best effect.
AUTO MODE: Always have the hoses attached in this mode,
When you set the air conditioner in AUTO mode, it will automatically select cooling,
heating(inapplicable for cooling only models), or fan only operation depending on what
temperature you have selected and the room temperature. The air conditioner will
control room temperature automatically round the temperature point set by you. Under
AUTO mode, you can not select the fan speed.
FAN MODE: In this mode there is no need to use the hoses or drainage hose.
1. Press the NODE button until the "Fan" indicator lights.
2. Press the FAN button to choose the desired fan speed.
3. The fan will run at the selected speed and the display will show the room temperature.
TIMER OPERATION: You can set both delay stop and delay start while unit is in ON position or OFF position.
When unit is in ON position, first press TIMER button to go to delay stop setting, then
"timer off" light will illuminate, tap or hold the UP arrow (A) or the DOWN arrow (V) to
change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments
up to 24 hours. Then press the TIMER button to confirm the setting (the control will confirm
the setting automatically after 5 seconds) and go to delay start setting. Use the same way
as above to set the delay start timing. If you don't need to set delay start, press the
TIMER button again to exit. After 5 seconds, the control will automatically change the
display back to previous temperature display. If you want to check remain timing, press the
TIMER button. The delay start operation automatically selects mode, temperature and
fan speed the same as last operation you set.
When unit is in OFF position, press TIMER button will first go to delay start setting, then
"timer on" light will illuminate, set the delay start and delay stop timing the same way
as above.
To cancel the timer setting, simply tap (A) or (V) button to change the timing to 0.0.
SLEEP OPERATION: In this mode the selected temperature will increase by 1 °C 30 minutes after the mode
is selected. The temperature will then increase by another 1 °C after an additional 30
minutes. This new temperature will be maintained for 7 hours before it returns to the
originally selected temperature. This ends the "Sleep" mode and the unit will continue to
operate as originally programmed. The "Sleep" mode program can be cancelled at any
time during operation by again pressing the "Sleep" button.
Note: This feature is unavailabe under FAN or DRY modes.
@2009 ElectroluxHome Products, Inc, All rights reserved. #._

Operating Instructions
(continued)
SWING OPERATION: When you turn on the unit, the louver will swing and stop at a certain angle. You
can press the SWING button to let the louver swing automatically. Pressthe
SWING button again while you want the louver stop at desired angle.
CHECK FILTER FEATURE: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more
efficient operation. The LED (light) which above the "Filter" button will illuminate
after 250 hours of operation. To reset after cleaning the filter, press the "Filter"
button and the light will go off.
FAULT CODE:
temp/timer setting
F
i°C
Hr
If the display reads "EA", the room temperature sensor has failed. Contact your Authorized
Frigidaire Service Center.
temp/timer setting
°F
m°C
Hr
temp/timer setting
m'C
Hr
temp/timer setting
w'C
Hr
If the display reads "ES", the evaporator temperature sensor has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "E4", the display panel communication has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "PI", bottom tray is full. Carefully move the unit to a drain location, remove
the bottom drain plug and let the water drain away. Restart the machine until the "PI" symbol
disappears. If error repeats, call for service.
DRAINAGE:
During the dehumidifying mode, you will need a garden hose (sold
separately) to drain the condensate from the unit.
Removethe rubber stopper from the hoseconnector, then screw on a
garden hose to the connector as shown on fig 23.
The hose may then: /x_ Girden hose
A. Discharge into a drain that is lower than the unit. /
B. Be connected to a condensate pump (sold separately).
Removethe
suppliedrubber
)er
Fig, 23
REMOTE CONTROL STORAGE:
The door on side of the unit is for storing the remote, to open press it as
shown in Fig. 24, to close simply push it back into position. Presshere
Fig. 24 ]
0 @2009 Electrolux Home Products, Inc. All rights reserved,