Frigidaire FRFS2823AD User manual

Frigidaire.com USA 1-800-374-4432 Frigidaire.ca Canada 1-800-265-8352
use
&
care
REFRIGERATOR
A20811503 (February 2022)
Introduction.......................................................2
Important Safety Information ....................3
Features..............................................................6
Installation .........................................................8
Door Removal.................................................. 11
Door Handle Installation............................. 16
Water Supply Connection.......................... 17
Controls and Settings.................................. 19
Automatic Ice & Water Dispenser ......... 26
Ice Maker ......................................................... 29
Storage Features........................................... 31
Storing Food and Saving Energy...........36
Normal Operating Sounds........................ 37
Filter Replacement ...................................... 38
Care & Cleaning ............................................. 41
Troubleshooting ..........................................43
Limited Warranty .........................................48

2INTRODUCTION
Doors
Handles are secure and tight
Door seals completely to cabinet on
all sides
Leveling
Refrigerator is level side-to-side and
slightly elevated in front to assist
with door and drawer closing (front
should be higher than back)
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to
refrigerator
WARNING: Potable water supply
only.
No water leaks present at all
connections - recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates
correctly
Final Checks
Shipping material removed
Fresh food and freezer temperatures
set
Crisper humidity controls set
Registration card sent in
Installation Checklist

Welcome to our family
Thank you for bringing Frigidaire into
your home! We see your purchase as the
beginning of a long relationship together.
This manual is your resource for the use
and care of your product. Please read
it before using your appliance. Keep it
handy for quick reference. If something
doesn’t seem right, the troubleshooting
section will help you with common issues.
FAQs, helpful tips and videos, cleaning
products, and kitchen and home accessories
are available at www.frigidaire.com.
We are here for you! Visit our website,
chat with an agent, or call us if you need
help. We may be able to help you avoid
a service visit. If you do need service, we
can get that started for you.
Let’s make it ocial! Be sure to register
your product.
Keep your product info here so it’s easy
to find.
Model Number
Serial Number
Purchase Date
Serial Number Location

3
WARNING
WARNING indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
IMPORTANT
IMPORTANT indicates installation, oper-
ation or maintenance information which
is important but not hazard-related.
DANGER
DANGER indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
CAUTION
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Safety Definitions
This is the safety alert symbol. It is
used to alert of potential personal injury
hazards. Obey all safety messages that
follow this symbol to avoid possible injury
or death.
WARNING
Please read all instructions before using
this appliance.
IMPORTANT SAFETY INFORMATION
DANGER
DANGER Risk of fire or explosion.
Flammable refrigerant used. Do not use
mechanical devices to defrost refrigera-
tor. Do not puncture refrigerant tubing.
DANGER Risk of fire or explosion.
Flammable refrigerant used. To be re-
paired only by trained service person-
nel. Use only manufacturer-authorized
service parts. Any repair equipment
used must be designed for flammable
refrigerants. Follow all manufacturer
repair instructions. Do not puncture
refrigerant tubing.
CAUTION
CAUTION Risk of fire or explosion.
Dispose of refrigerator properly
in accordance with the applicable
federal or local regulations. Flammable
refrigerant used.
CAUTION Risk of fire or explosion
due to puncture of refrigerant tubing.
Follow handling instructions carefully.
Flammable refrigerant used.
WARNING
CALIFORNIA RESIDENTS ONLY
WARNING! Cancer and Reproductive Harm
www.P65Warnings.ca.gov

4
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cool-
ing system that used CFCs or HCFCs
(chlorofluorocarbons or hydrochlorofluo-
rocarbons). CFCs and HCFCs are believed
to harm stratospheric ozone if released to
the atmosphere. Other refrigerants may
also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old refrig-
erator, make sure the refrigerant is re-
moved for proper disposal by a qualified
technician. If you intentionally release
refrigerant, you may be subject to fines
and imprisonment under provisions of
environmental legislation.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your
utility company or visit www.energystar.gov/
recycle for more information on recycling
your old refrigerator.
Before you throw away your old
refrigerator/freezer:
• Remove doors.
• Leave shelves in place so children
may not easily climb inside.
• Have refrigerant removed by a
qualified service technician.
IMPORTANT SAFETY INFORMATION
Safety Instructions
• DO NOT store or use gasoline,
or other flammable liquids in
the vicinity of this or any other
appliance. Read product labels for
warnings regarding flammability and
other hazards.
• DO NOT operate the refrigerator in
the presence of explosive fumes.
• Avoid contact with any moving parts
of automatic ice maker.
• Remove all staples from the carton.
Staples can cause severe cuts, and
also destroy finishes if they come
in contact with other appliances or
furniture.
Child Safety
Destroy or recycle the carton, plastic
bags, and any exterior wrapping material
immediately after the refrigerator is
unpacked. Children should NEVER use
these items to play. Cartons covered with
rugs, bedspreads, plastic sheets or stretch
wrap may become airtight chambers, and
can quickly cause suocation.
WARNING
Do not use electrical appliances inside
the food storage compartments of the
appliance unless they are of the type
recommended by the manufacturer.
Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suocation are
not problems of the past. Junked or
abandoned refrigerators or freezers are
still dangerous – even if they will sit for
“just a few days”. If you are getting rid
of your old refrigerator or freezer, please
follow the instructions below to help
prevent accidents.

5
Electrical information
• The refrigerator must be plugged
into its own dedicated 115 Volt, 60
Hz., 15 Amp, AC only electrical outlet.
The power cord of the appliance
is equipped with a three-prong
grounding plug for your protection
against electrical shock hazards.
It must be plugged directly into
a properly grounded three prong
receptacle. The receptacle must be
installed in accordance with local
codes and ordinances. Consult
a qualified electrician. Avoid
connecting refrigerator to a Ground
Fault Interrupter (GFI) circuit. Do
not use an extension cord or adapter
plug.
• If the power cord is damaged, it
should be replaced by an authorized
service technician to prevent any
risk.
• Never unplug the refrigerator by
pulling on the power cord. Always
grip the plug firmly, and pull straight
out from the receptacle to prevent
damaging the power cord.
• Unplug the refrigerator before
cleaning and before replacing a light
bulb to avoid electrical shock.
• Performance may be aected if
the voltage varies by 10% or more.
Operating the refrigerator with
insucient power can damage the
compressor. Such damage is not
covered under your warranty.
• Do not plug the unit into an
electrical outlet controlled by a wall
switch or pull cord to prevent the
refrigerator from being turned o
accidentally.
IMPORTANT
Pressing and holding the On/O button
for three seconds, located on the tem-
perature control panel, will disable your
refrigerator’s cooling system but does
not disconnect the power to the light
bulb and other electrical components.
To turn o power to your refrigerator
you must unplug the power cord from
the electrical outlet.
Grounding type wall receptacle
Power cord with
3-prong grounded plug
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly
if nicked, scratched, or exposed to
sudden temperature change.
IMPORTANT SAFETY INFORMATION

6
IMPORTANT
Accessories are available for your appliance and may be purchased at
Frigidaire.com or by calling 1-800-374-4432 (Frigidaire.ca or 1-800-265-8352 in
Canada) or from an authorized seller.
AWater Filter
BCondiment Bin
CL-Shaped Bin
DDairy Bin
EFlipper Mullion
FGallon Bin
GSlim Bin
HFresh Food Ice Maker & Bin
IFlipper Guide
JAir Filter
KEdge-to-edge Glass Shelving
LStandard bin
MCrisper Drawers
N Deli Drawer
OUpper Freezer Baskets
PLower Freezer Baskets
QExternal Control Display
RIce/Water Dispenser
Quick
Freeze
External Water Dispenser Model
FEATURES
B
C
D
E
F G
H
I
J
K
M
N
O
P
Q
R
L
A

7
FEATURES
IMPORTANT
Accessories are available for your appliance and may be purchased at
Frigidaire.com or by calling 1-800-374-4432 (Frigidaire.ca or 1-800-265-8352 in
Canada) or from an authorized seller.
AWater Filter
BCondiment Bin
CGallon Bin
DFlipper Mullion
EFlipper Guide
FAir Filter
GEdge-to-edge Glass Shelving
HStandard bin
ICrisper Drawers
J Deli Drawer
KUpper Freezer Baskets
LLower Freezer Baskets
MFreezer Ice maker
NNon-Dispenser control (side
door)
Non- Dispenser Model
B
C
D
E
F
G
H
I
K
M
N
L
J
A

8
Tools Necessary:
Phillips Head
or
Quadrex Head
Screwdriver
(OR) OR
⅜" and ¼"
Socket
Wrench
Adjustable
Wrench
OR
⅜"
Fixed
Wrench
ANDAND
6mm
Allen Wrench
INSTALLATION
CAUTION
Do Not install the refrigerator where
the temperature will drop below 55°F
(13°C) or rise above 110°F (43°C).
The compressor will not be able to
maintain proper temperatures inside
the refrigerator.
This Use & Care Manual provides general
installation and operating instructions
for your model. We recommend
using a service or kitchen contracting
professional to install your refrigerator.
Use the refrigerator only as instructed in
this Use & Care Manual. Before starting
the refrigerator, follow these important
first steps.
Location
• Choose a place that is near a
grounded, non-GFCI, electrical
outlet. Do Not use an extension cord
or an adapter plug.
• If possible, place the refrigerator
out of direct sunlight and away from
the range, dishwasher, or other heat
sources.
• The refrigerator must be installed
on a floor that is level and strong
enough to support a fully loaded
refrigerator.
• Consider water supply availability
for models equipped with an
automatic ice maker.
Top Hinge
Cover Front
Screw
Top Hinge
Cover Rear
Screw
Lower
Hinge
Screw
Top
Hinge
Screw
Components Provided:
WARNING
Installation
Allow the following clearances
for ease of installation, proper air
circulation, and plumbing and electrical
connections:
• Sides & Top ³⁄8inch (9.5 mm)
• Back 1 inch (25.4 mm)
WARNING
This appliance is intended for use
in residential household and similar
interior applications such as:
• Kitchen / Kitchenette
• Pantry Room
• Basement
• Enclosed Garage
• Other interior residential type
environments

9
INSTALLATION
NOTE
If your refrigerator is placed with the
door hinge side against a wall, you may
have to allow additional space so the
door can be opened wider.
NOTE
Product is shipped with doors adjusted
to the lowest position on the hinges.
Door opening
Your refrigerator should be positioned
to allow easy access to a counter
when removing food. For best use of
refrigerator drawers and freezer baskets,
the refrigerator should be in a position
where both can be fully opened.
3. Ensure both doors are bind-free with
their seals touching the cabinet on all
four sides and that cabinet is stable.
4. After unit is leveled, lower the anti-
tip leg until it firmly contacts the
floor. An adjustable wrench may be
necessary for adjustment.
Cabinet Leveling & Refrigerator
Door Alignment (if necessary)
Guidelines for final positioning of refrigerator:
• All four corners of the cabinet must
rest firmly on the floor.
• The front should be slightly elevated
to ensure that doors close and seal
properly.
• Doors should align with each other
and be level.
Most of these conditions can be met by
raising or lowering the adjustable front rollers.
To level the cabinet using the front rollers:
1. Slightly open freezer drawer to
reveal adjustable rollers at bottom of
cabinet.
2. Use the front roller height adjusting
screws to make initial cabinet
adjustments. Use a 3/8 inch socket
wrench to turn the adjustment
screws (1 per side).
To raise unit: Turn adjustment
screw clockwise.
To lower unit: Turn adjustment screw
counterclockwise.
Door
Door
To make final door height adjustments:
1. Open freezer drawer to access
hinges for fresh food doors.
2. Insert 6mm AllenTM wrench into the
shaft of the lower hinge. (Included
with unit)
To lower door: turn adjustment
screw counter-clockwise if looking
at the door from below.
To raise door: turn adjustment
screw clockwise if looking at the
door from below.
Raise
Lower
Anti-tip
Leg

10 INSTALLATION
Adjusting Flipper Mullion Screw
2. Adjust flipper mullion height. For
proper connection with the flipper
mullion guide, there should be a
separation about the thickness of
a coin (0.060 inches, or 1.5 mm)
between the guide and flipper
mullion.
3. Re-tighten screws.
To adjust the flipper mullion:
1. Loosen the two screws located on
the flipper mullion hinge.
Adjusting Flipper Mullion Height
Flipper
Mullion
Screws
Flipper Mullion
Adjust Flipper Mullion for proper
connection with the mullion guide by
ensuring the flipper mullion is folded and
perpendicular to the fresh food door. If
the mullion guide is not in the correct
position, it could prevent the door from
closing completely.
WRONG
Flipper
Mullion
Mullion
Guide
Thickness
of a Coin

11
DOOR REMOVAL
WARNING
Make sure the electrical power cord is
unplugged from the wall outlet.
Getting through narrow spaces
If your refrigerator will not fit through an
entrance area, you can remove the doors.
Check first by measuring the entrance.
To prepare for removing the doors:
1. Make sure the electrical power cord
is unplugged from the wall outlet.
2. Remove any food from the door
shelves and close the doors.
Right Door Non-Dispenser Unit
Right Door Dispenser Unit
Left Door Dispenser Unit
Left Door Non- Dispenser Unit
To remove refrigerator doors:
1. Remove the three screws from both
hinge covers on the left and right
top of the cabinet, taking care not
to damage electrical connections or
sensors.
2. After the hinge covers are removed,
disconnect any harnesses between
the cabinet and doors by grasping
both sides of the connector firmly,
depress the latch and pull apart.

12 DOOR REMOVAL
5. Pull the water tube out of the
conduit from the top of the cabinet.
Press
Press
Press
Press
6. Open both doors to a 90 degree
angle.
NOTE
You will be pulling approximately five
feet of water tube from the back of the
refrigerator. Use care while pulling the
water tube from the unit to be sure that
you do not kink the tube.
90˚
CAUTION
Be sure doors are set aside in a secure
position where they cannot fall and
cause personal injury, or damage to the
doors or handles.
3. Trace lightly around the door’s top
hinges with a pencil. This makes re-
installation easier.
4. Remove bulkhead cover at rear
of unit to access water tubing.
Disconnect the water tube at the
push-lock connection on the rear
of the unit below the bulkhead. The
dispenser line is connected to the
yellow water line coming from the
main water valve.

13
DOOR REMOVAL
7. Remove hex screws from top hinge
plate, then remove the top hinge.
8. Lift doors o bottom hinges and set
aside.
9. Unscrew the three bottom hinge
screws and remove the bottom
hinges.
Lower Hinge Removal
Pin
Mechanism
Bottom
Hinge
Opening
NOTE
When reinserting the water tube and
replacing the top hinge cover, use care
to be sure you do not kink the tube.
The water line may also be dicult to
pass back through the conduit inside
the cabinet
To reinstall the refrigerator
doors:
1. Replace three bottom hinge screws
and hinges on both sides of the
cabinet. Ensure screws are tightly
snug to hinges on both sides of the
cabinet before re-installing doors
2. Holding the door at a 90 degree
angle, drop the pin down into the
bottom hinge opening. Rotate it
slightly in either direction until the
door falls onto the hinge and is fully
seated.

14 DOOR REMOVAL
Bottom of the Doors
For
RIGHT DOOR,
turn pin 90˚
counter-
clockwise
For
LEFT DOOR,
turn pin 90˚
clockwise
To reset door pin:
If doors are removed at less than a 40
degree angle, the pin returns to the home
position. It can be reset by turning the
door upside down and using a 5/32” Allen
wrench to rotate the left hand pin 90
degrees clockwise and the right hand pin
90 degrees counterclockwise.
Once the door pins are reset, follow the
steps “To reinstall the refrigerator doors”.
3. Reinstall top hinges and screws.
4. Insert and feed water line back into
the conduit at the top left door
hinge until tube re-appears at rear
of unit.
Push
Push
5. Reconnect all harnesses.
6. Replace top hinge covers and
screws.
7. Reconnect water line to push-lock
connection and reinstall water line
bulkhead cover at rear of unit.
8. Reconnect electrical power cord to
the wall outlet
NOTE
Upon replacement, the tube needs to
be fully inserted up to the marking line.

15
DOOR REMOVAL
CAUTION
Drawer is heavy. Use caution when lifting.
Removing Freezer Drawer
1. Remove 4 hex head drawer screws
(2 per side) that secure the drawer
to the slide assemblies.
2. Lift up drawer to remove.
Remove
Hex Head
Drawer
Screw
CAUTION
Do Not loosen or remove the 3 hex screws.
NOTE
To locate the pin, look inside the drawer
and the pin is next to the door liner and
the slides. Not all parts are shown in the
illustration.
Replacing Freezer Drawer
1. Extend the Freezer slides from the
unit.
2. Carefully align support pin with
hooks on end of freezer slides and
then lower freezer door onto slides.
3. Replace the 4 hex head screws that
secure the slides to the door (2 on
each side) and tighten.

16 DOOR HANDLE INSTALLATION
CAUTION
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.
NOTE
All set screws should be tightened so the screw is below the surface of the handle.
The handles should be drawn tight to freezer and refrigerator doors with no gaps.
Opening the opposite door while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this hap-
pens, tighten the set screws on the handles.
Door Handle Mounting
Instructions
1. Remove handles from carton
and any other protective
packaging.
2. Position refrigerator handle end
caps over upper and lower pre-
installed shoulder bolts (A) that
are fastened into door, ensuring
the holes for the set screws are
facing towards the opposite door.
3. While holding handle firmly
against door, fasten upper and
lower Allen set screws (B) with
supplied Allen wrench.
4. Repeat steps 2 and 3 to install
opposite handle. Ensure the
holes for the set screws are
facing towards the opposite
door.
5. Position freezer handle end caps
over left and right pre-installed
shoulder bolts (A) that are
fastened to the door, ensuring
the holes for the set screws are
facing down.
6. While holding handle firmly
against door, loosely tighten
right Allen set screw (B) with
supplied Allen wrench until
there is no gap between handle
and door.
7. Still holding the handle firmly to
the door, firmly tighten left Allen
set screw (B) with supplied Allen
wrench.
8. Return to the right Allen set
screw (B) and firmly tighten
with supplied Allen wrench.
Mounting Refrigerator Handles
NOTE
When tightening the Allen set screws, it
is important that force be applied to the
longer arm of the Allen wrench supplied in
the handle packaging.
Mounting Freezer Handle
A A
B B
A A
AA
B
B
B
B

17
WATER SUPPLY CONNECTION
WARNING
To avoid electric shock, which can
cause death or severe personal injury,
disconnect the refrigerator from
electrical power before connecting a
water supply line to the refrigerator.
NOTE
Check with your local building au-
thority for recommendations on water
lines and associated materials prior
to installing your new refrigerator.
Depending on your local/state build-
ing codes, Frigidaire recommends for
homes with existing valves its Smart
Choice®water line kit 5305513409 with
a 6ft. (1.8 meters) Stainless Steel Water
Line, and for homes without an existing
valve Frigidaire recommends its Smart
Choice®water line kit 5305510264 with
a 20ft. (6meters) Copper Water Line
with self-tapping saddle valve. Please
refer to www.frigidaire.com/store for
more information.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided
tubing is recommended for the
water supply line. Water supply
tubing made of ¼inch plastic is not
recommended to be used. Plastic
tubing greatly increases the potential
for water leaks, and the manufacturer
will not be responsible for any
damage if plastic tubing is used for
the supply line.
• DO NOT install water supply tubing
in areas where temperatures fall
below freezing.
• Chemicals from a malfunctioning
water softener can damage the ice
maker. If your home has a water
softening system, ensure the softener
is maintained and working properly.
IMPORTANT
Ensure that your water supply line con-
nections comply with all local plumbing
codes.
Before Installing The Water
Supply Line, You Will Need:
• Basic Tools: adjustable wrench,
flat-blade screwdriver, and PhillipsTM
screwdriver
• Access to a household cold water
line with water pressure between 30
and 100psi.
• A water supply line made of ¼inch
(6.4mm) OD, copper or stainless
steel tubing. To determine the length
of tubing needed, measure the
distance from the ice maker inlet
valve at the back of the refrigerator
to your cold water pipe. Then add
approximately 6 ft. (1.8 meters) , so
the refrigerator can be moved out
for cleaning (as shown).
• A shuto valve to connect the water
supply line to your household water
system. DO NOT use a self-piercing
type shuto valve.
• Do not re-use compression fitting or
use thread seal tape.
• A compression nut and ferrule
(sleeve) for connecting a copper
water supply line to the ice maker
inlet valve.
To Connect Water Supply Line
To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric
power source.
2. Place end of water supply line
into sink or bucket. Turn ON water
supply and flush supply line until
water is clear. Turn OFF water
supply at shuto valve.
3. Remove plastic cap from water valve
inlet and discard cap.

18
IMPORTANT
Your refrigerator’s water supply system
includes several tubing lines, a water
filter, and a water valve. To ensure that
your water dispenser works properly,
this system must be completely filled
with water when your refrigerator is
first connected to the household water
supply line.
WATER SUPPLY CONNECTION
NOTE
These instructions do not cover after
market ice maker installation. Instruc-
tions in after market ice maker kit
should be used.
Figure 2
4. If you use copper tubing - Slide
brass compression nut, then
ferrule (sleeve) onto water supply
line. Push water supply line into
water valve inlet as far as it will
go (¼inch/6.4mm). Slide ferrule
(sleeve) into valve inlet and finger
tighten compression nut onto valve.
Tighten another half turn with a
wrench; DO NOT over tighten. See
Figure 1.
• If you use braided flexible stainless
steel tubing - The nut is already
assembled on the tubing. Slide nut
onto valve inlet and finger tighten
nut onto valve. Tighten another half
turn with a wrench; DO NOT over
tighten. See Figure 2.
5. With steel clamp and screw, secure
water supply line to rear panel of
refrigerator as shown.
6. Coil excess water supply line
(copper tubing only), about
2½turns, behind refrigerator as
shown and arrange coils so they
do not vibrate or wear against any
other surface. Do not kink tubing.
7. Turn ON water supply at shuto
valve and tighten any connections
that leak.
8. Reconnect refrigerator to electrical
power source.
9. To turn ice maker on, ensure Ice
Maker is enabled on display (LED
will be lit) or set the ice maker’s
On/o power switch to the “ON”
position (freezer ice maker).
Steel
Clamp
Steel
Clamp
Valve Inlet
Water Valve
Braided
Flexible
Stainless
Steel
Water Line
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
Water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper waterline
from household
water supply
(Include enough tubing
in loop to allow moving
refrigerator out for cleaning)
(Include enough
tubing in loop
to allow moving
refrigerator out
for cleaning)
6 ft. (1.8 Meters)
Braided flexible
stainless steel water
line from household
water supply.
Figure 1

19
WARNING
When using the cold drink timer, make
sure to remove drinks from freezer
compartment when alarm sounds.
Carbonated drinks may explode if left
in freezer for too long.
CONTROLS AND SETTINGS
Awake Mode Display
Awake Mode
To change from sleep mode (on) to awake mode (o), simultaneously press and hold
“Crush” and “ Light” icons for 5 seconds. Display will show the current temperature/ice
maker status. Tone will confirm.
Quick
Freeze
Sleep Mode
As a default, the display will go to sleep after a short time. If any icon is pressed, the
display will be awakened. After a short time, it will go back to sleep. When in sleep
mode, wake up the display to confirm ice maker is On/O. Sleep mode can be turned
o to have the display on full time (awake mode). When sleep mode is O, the display
will always be illuminated. To turn sleep mode On/O, simultaneously press and hold
“Crush” and “ Light” icons for 5 seconds. Tone will confirm.
Sleep Mode Display
Quick
Freeze
External Water Dispenser Control Display Mode Views

20 CONTROLS AND SETTINGS
1Freeze Boost (on/o)
Prior to grocery shopping, we
recommend you activate Freeze
Boost to lower the temperature and
freeze food faster. Freeze Boost
will remain active for up to 24 hours
before automatically deactivating or
manually exiting by pressing Freeze
Boost to turn the function o. This
will reset the freezer to the previous
temperature setting.
2Ice Maker
Press and hold for 3 seconds to turn
ice maker on/o. When indicator is
lit, ice maker is on. When indicator
is not lit, ice maker is in the OFF
state and will stop making ice. While
o, ice dispensing can continue as
long as there is ice in the bucket.
When ice maker is o and ice is
dispensing, indicator will blink.
3The lock button can be used to lock
the display preventing it from being
used in certain situations. Press
and hold for 3 seconds to enable/
disable. While in the locked state,
no changes can be made to settings
on the display. Dispensing ice and
water will be disabled. The indicator
will flash and an audible warning
tone is played.
4Power Outage
In the event of a power outage,
the power outage alert will be
illuminated once power has been
restored and a tone will sound.
Press any button to silence the tone.
5Adjusting Temp
Illuminates when temperatures are
changed on the display and will
remain illuminated until the desired
temperatures are reached inside
the refrigerator and freezer. Press
either the + or - to adjust to desired
temperature setting.
Freezer temp - Control
temperatures range from -6°F /
-21°C to +6°F / -15°C.
Refrigerator temp - Control
temperatures range from +34°F
/ +1°C to +44°F / +7°C. This unit
is designed to operate at 37°F
Refrigerator/0°F Freezer. Unit
should stabilize temperatures within
24 hours of installation.
1
2
3
5
10
6
7
9
8
11 12
13
14
4
15
External Water Dispenser Control Display