FRO­NIUS 1.5-1 User manual

Installation
Instructions
Fronius Galvo 208-240:
1.5-1 / 2.0-1
2.5-1 / 3.1-1
10.0-1 / 11.4-1
12.5-1 / 15.0-1
42,0426,0182,EA 017-10082022
EN-US Installation instructions

Table of contents
Safety 5
Explanation of Safety Instructions 5
General 5
Electrical installations 5
Safety 6
Intended Use 7
Installation location and position 8
Selecting a location 8
Installation position 9
General location selection 10
Example: Installation of several inverters 11
Preparation 13
Attaching the Mounting Bracket 15
Safety 15
Selecting Dowels and Screws 15
Screw recommendation 15
Opening the inverter 16
Installing the mounting bracket on a brick or concrete wall 16
Fitting the mounting bracket to a timber wall 17
Do not warp or deform the mounting bracket 17
Attaching the mounting bracket to a metal carrier 18
Installing the inverter on a mast 18
Notes on the Knockouts 19
Safety 19
General 19
Knocking or drilling out knockouts 20
AC~ 21
Suitable Grids 23
Suitable Grids 23
Connecting the inverter to the public grid (AC side) 25
Safety 25
Permitted cables 26
Preparing Aluminum Cables for Connection 27
Monitoring the grid 27
Notes on grid connection 28
Grid Connection 28
Maximum AC-side Overcurrent Protection 29
Additional external AC and/or DC disconnect 29
DC= 31
Notes on Solar Module Grounding in the Inverter 33
Notes on solar module ground in the inverter 33
Notes on DC Connection 35
Safety 35
General Information about Solar Modules 37
Inverter DC Connection 37
Notes on Laying Data Communication Cables 38
Laying Data Communication Cables 38
Notes on Clipping the Inverter into the Wall Bracket 39
Clipping the Inverter into the Wall Bracket 39
Notes on Anti-theft device 40
Anti-Theft Device 40
Notes on Software Updates 42
Notes on Software Updates 42
USB Stick as a Data Logger and for Updating Inverter Software 43
USB Flash Drive as a Data Logger 43
3
EN-US

Data on the USB stick 43
Data Amount and Memory Capacity 44
Buffer Memory 45
Suitable USB Thumb Drives 45
USB Stick for Updating Inverter Software 46
Removing the USB Stick 46
Notes on Maintenance 47
Maintenance 47
Cleaning 47
Serial Number Sticker for Customer Use 48
Serial number sticker for customer use 48
4

Safety
Explanation of
Safety Instruc-
tions
DANGER!
Indicates an immediate danger.
▶Death or serious injury may result if appropriate precautions are not taken.
WARNING!
Indicates a possibly dangerous situation.
▶Death or serious injury may result if appropriate precautions are not taken.
CAUTION!
Indicates a situation where damage or injury could occur.
▶Minor injury or damage to property may result if appropriate precautions are
not taken.
NOTE!
Indicates the possibility of flawed results and damage to the equipment.
General This manual contains important instructions for the inverter that must be fol-
lowed during installation and maintenance of the inverter.
The inverter is designed and tested according to international safety require-
ments. Due to its electrical and electronic components, certain precautions must
be taken when installing and operating the inverter.
In order to reduce the risk of injury to persons and to ensure safe installation and
operation of the inverter, be sure to read these Operating Instructions carefully
and follow all instructions and safety instructions.
Failure to observe the Operating Instructions and safety instructions can void
the warranty and/or cause damage to the inverters or other property damage!
Electrical in-
stallations
All electrical installations must be carried out in accordance with the National
Electrical Code, ANSI/NFPA 70, and any other codes and regulations applicable
to the installation site.
For installations in Canada, the installations must be done in accordance with
applicable Canadian standards.
5
EN-US

Safety WARNING!
Danger from incorrect operation and work that is not carried out properly.
This can result in severe personal injury and damage to property.
▶Only qualified personnel are authorized to commission your inverter and only
within the scope of the respective technical regulations.
▶Read the Installation Instructions and Operating Instructions before in-
stalling and commissioning the equipment.
WARNING!
Danger due to a ground fault. A normally grounded conductor can become un-
grounded and live due to a ground fault.
An electric shock can be fatal.
▶A ground fault must be repaired before operation is resumed.
WARNING!
Danger of DC voltage from solar modules. When solar modules are grounded,
the inverter's insulation monitoring is deactivated.
An electric shock can be fatal.
▶Ensure that grounded solar modules are double insulated according to
Safety Class II.
▶Attach corresponding safety labels to the photovoltaic system where they
can be seen easily.
▶Set the inverter so that an error message is displayed if the fuse trips.
Fire prevention
CAUTION!
Danger from faulty or incorrect installations.
They may result in damage to inverters and other current-carrying components
of a photovoltaic system.
Faulty or improper installation may cause overheating of cables and terminals as
well as the formation of arcs. This could cause thermal damage, which in turn
may lead to fires.
Please note the following when connecting the AC and DC cables:
▶Securely tighten all terminals using the proper torque listed in the Operating
Instructions
▶Securely tighten all grounding terminals (PE/GND) using the proper torque
listed in the Operating Instructions, even for free grounding terminals
▶Do not overload cables
▶Check cables for damage and correct wiring
▶Follow all Safety Instructions, Operating Instructions, and any local connec-
tion regulations
▶Always secure the inverter to the mounting bracket with fixing screws using
the torque specified in the Operating Instructions.
▶Only start up the inverter with the fixing screws tightened.
NOTE!
Follow general ESD guidelines when handling option cards.
6

NOTE!
Fronius will not bear any costs for production downtimes, or for installations,
etc., which may arise due to a detected electric arc and its consequences.
Fronius accepts no liability for fires which may break out despite integrated arc
detection/interruption (e.g., due to a parallel arc).
NOTE!
Before an inverter can be reset following a detected electric arc, check the en-
tire affected photovoltaic system for any damage.
Intended Use The inverter is designed exclusively to convert direct current from solar modules
into alternating current and feed this power into the public grid.
The following are deemed to be not in conformity with its intended purpose:
-Utilization for any other purpose, or in any other manner
-Alternations to the inverter are not expressly recommended by Fronius
-Installation of components that are not expressly recommended or sold by
Fronius.
The manufacturer is not responsible for any damage resulting from improper use.
All warranty claims are considered void in such cases.
Proper use also means
-carefully reading and obeying the instructions and all the safety and danger
notices in the Operating and Installation Instructions
-compliance with the maintenance operations
-installation as specified in the Installation Instructions
When configuring the photovoltaic system, make sure that all components are
operating completely within their permitted operating range.
All measures recommended by the solar module manufacturer for maintaining
solar module properties must be followed.
Follow all grid operator regulations regarding grid power feed and connection
methods.
7
EN-US

Installation location and position
Selecting a loca-
tion
Please observe the following criteria when choosing a location for the inverter:
The inverter is suitable for indoor installation.
The inverter is suitable for outdoor installation.
Because of its NEMA4X protection class, the inverter is not sus-
ceptible to hose water on any side and can also be operated in
moist environments.
In order to keep inverter heating as low as possible, do not expose
the inverter to direct sunlight. The inverter should be installed in a
protected location, e.g., near the solar modules or under an over-
hanging roof.
Altitude above sea level: up to 11,482 ft. (3500 m)
IMPORTANT! The inverter must not be installed or operated
above an altitude of 11,482 ft (3500 m).
The max. permissible DC voltage of the inverter depends on the
altitude:
-0 - 6561 ft. (0 - 2000 m) ... UDC max = 550 V
-> 6561 - 8202 ft. (> 2000 - 2500 m) ... UDC max = 540 V
-> 8202 - 9842 ft. (> 2500 - 3000 m) ... UDC max = 480 V
-> 9842 - 11,482 ft. (> 3000 - 3500 m) ... UDC max = 430 V
The output power reduces when the device temperature is too
high, and this may occur earlier than normal at increased alti-
tudes.
NH3
Do not install the inverter:
-Where it may be exposed to ammonia, corrosive gases, acids,
or salts
(e.g., fertilizer storage areas, vent openings for livestock
stables, chemical plants, tanneries)
8

During certain operating phases the inverter may produce a slight
noise. For this reason it should not be installed in an occupied liv-
ing area.
Do not install the inverter in:
-Areas where there is an increased risk of accidents from farm
animals (horses, cattle, sheep, pigs, etc.)
-Stables or adjoining areas
-Storage areas for hay, straw, chaff, animal feed, fertilizers, etc.
Do not install the inverter in:
-Dusty rooms and environments
-Rooms and areas with large amounts of conductive dust
particles (e.g., iron filings)
Do not install the inverter in:
-Greenhouses
-Storage or processing areas for fruit, vegetables, or viticulture
products
-Areas used in the preparation of grain, green fodder, or animal
feeds
Installation posi-
tion
The inverter is suitable for vertical installation on a vertical wall or
column.
The inverter is suitable for a horizontal installation position.
The inverter is suitable for installation on a sloping surface.
Do not install the inverter on a sloping surface with the connec-
tions upwards.
9
EN-US

Do not install the inverter in a sloping position on a vertical wall or
column.
Do not install the inverter in a horizontal position on a vertical
wall or column.
Do not install the inverter with the connections upwards on a ver-
tical wall or column.
Do not install the inverter overhanging with the connections up-
wards.
Do not install the inverter overhanging with the connections
downwards.
Do not install the inverter on the ceiling.
General location
selection
Please observe the following criteria when choosing a location for the inverter:
Only install on a solid, non-flammable surface
10