FS UMC-GA1F1T User manual

TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
UNMANAGED ETHERNET MEDIA
CONVERTERS
Quick Start Guide V3.0
CONVERTISSEURS DE MÉDIA ETHERNET NON
GÉRÉS
UNMANAGED ETHERNET MEDIENKONVERTER
Quick-Start Anleitung
Guide de Démarrage Rapide

- 1 -EN
Introduction
Thank you for choosing FS Mini Unmanaged Ethernet Media Converters.
This guide is designed to familiarize you with the layout of the media
converters and describes how to deploy them in your network.
TP1/LNK TP2/LNK FX/LNK PWR
UMC-GA1F2T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
UMC-GA1F1T
UMC-GA1F2T

MFMC-12DP
PWR2
FAN2
PWR1
FAN1
PWR2 PWR1
FAN2 FAN1
ON INPUT: AC 100-240V 50/60Hz
FUSE: 3.15A
FAN
OFF
ON INPUT: AC 100-240V 50/60Hz
FUSE: 3.15A
FAN
OFF
PWR1PWR2
12
10
9
8
7
6
4
2
13511 AFN2FAN1
SPD FX/LNK PWR
TP/LNK
UMC-GA1SC1T-MM
10/100/1000BASE-T to 100/1000BASE-X
Unmanaged Multimode Gigabit Ethernet Media Converter
UMC-GA1SC1T-MM
SPD FX/LNK PWR
TP/LNK
UMC-GA1SC1T-SM
10/100/1000BASE-T to 100/1000BASE-X
Unmanaged Single Mode Gigabit Ethernet Media Converter
UMC-GA1SC1T-SM
- 2 -EN

Accessories
Power Adapter x1
NOTE: The power adapter will be packed according to the
plug standard of dierent regions. This picture is for reference
only. Please refer to the product received.
UMC-GA1F1T/UMC-GA1F2T/
UMC-GA1SC1T-MM/UMC-GA1SC1T-SM:
MFMC-12DP:
Power Cords x2 M4 Screws x N Mounting Bracket x12
- 3 -EN

Hardware Overview
Front Panel Ports
UMC-GA1F1T
RJ45 Port
1000M PWRFX/LNK
TP/LNK
SFP Port
Ports Description
RJ45
SFP
10/100/1000Base-T RJ45 port for Ethernet connection
Hot swappable SFP port for 1G ber connection
UMC-GA1F2T
TP2/LNK PWRFX/LNK
TP1/LNK
RJ45 Port RJ45 Port SFP Port
- 4 -EN

- 5 -EN
UMC-GA1SC1T-MM/UMC-GA1SC1T-SM
Ports Description
RJ45
SC
10/100/1000Base-T RJ45 port for Ethernet connection
SC port for duplex SC single mode or multimode ber
connection
SPD PWRFX/LNK
TP/LNK
RJ45 Port SC Port SC Port

Panel LEDs
Model: UMC-GA1F1T
1000M PWRFX/LNK
TP/LNK
TP/LNK 1000M FX/LNK PWR
LED Status Description
TP/LNK
Green Link through copper port is successfully
established, but no data transmission.
Copper port is actively sending or
receiving data.
Copper port is linked down.O
Blinking
Green
FX/LNK
1000M
Copper port is operating at 1000Mbps.
Copper port is operating at 10/100Mbps.O
Green
PWR Green The device is powered on.
Fiber port is actively sending or
receiving data.
Green
Blinking
Green
O Fiber port is linked down.
Link through ber port is successfully
established, but no data transmission.
- 6 -EN

Model: UMC-GA1F2T
TP2/LNK PWRFX/LNK
TP1/LNK
TP1/LNK TP2/LNK FX/LNK PWR
LED Status Description
TP1/LNK
Green TP1 port is operating at 1000Mbps.
TP1 port is operating at 100Mbps.
TP1 port is operating at 10Mbps.
Red
FX/LNK
TP2/LNK
TP2 port is operating at 1000Mbps.
TP2 port is operating at 100Mbps.Red
Green
PWR Green The device is powered on.
Fiber port is actively sending or
receiving data.
Green
Blinking
Green
O Fiber port is linked down.
TP2 port is operating at 10Mbps.
Dual Color
1
Dual Color
1
NOTE:
Dual color: Two LED chips (in one package) are all
bright or blinking at the same time. The LED color resembles
orange.
1
Link through ber port is successfully
established, but no data transmission.
- 7 -EN

- 8 -EN
Model: UMC-GA1SC1T-MM/UMC-GA1SC1T-SM
LED Status Description
TP/LNK
Green The link through TP port is successfully
established.
The TP port is actively sending or
receiving data.
The TP port link is down.
Blinking
Green
FX/LNK
SPD
The TP port is operating at 1000Mbps.
The TP port is operating at 10/100Mbps.O
Green
PWR Green The device is powered on.
The ber port is actively sending or
receiving data.
Green
Blinking
Green
O The ber port link is down.
O
The link through ber port is
successfully established.
SPD PWRFX/LNK
TP/LNK
TP/LNK SPD FX/LNK PWR

- 9 -EN
LED Status Description
PWR1/PWR2
FAN1/FAN2
Green The device is powered on.
The fan is working properly.Green
Model: MFMC-12DP
Model: UMC-GA1F1T/UMC-GA1F2T/UMC-GA1SC1T-MM/
UMC-GA1SC1T-SM
PWR2
FAN2
PWR1
FAN1
PWR2 PWR1
FAN2 FAN1
ON INPUT : AC 100-240V 50/60Hz
FUSE : 3.15A
FAN
OFF
ON INPUT : AC 100-240V 50/60Hz
FUSE : 3.15A
FAN
OFF
Rear Panel
DC
5-12V
Model: MFMC-12DP
PWR2
FAN2
PWR1
FAN1
PWR2 PWR1
FAN2 FAN1
ON INPUT : AC 100-240V 50/60Hz
FUSE : 3.15A
FAN
OFF
ON INPUT : AC 100-240V 50/60Hz
FUSE : 3.15A
FAN
OFF
LED Indicator Power Switches Two Built-in Fans Grounding Point
Dual AC Redundancy Power Supplies

Model: UMC-GA1F1T
Bottom Panel (DIP Switch)
ON
1 2 3 4
DIP
NOTE: LFP (Link Fault Pass Through) Function: If enabled,
when a device is connected to the converter and the TP/ber
line loses the link, the converter's ber will disconnect the link
of transmit.
ALS (Automatic Laser Shutdown) Function: If enabled, the
output power of the SFP transmitter will be automatically shut
down in case of ber break.
FX Reset: If enabled, when FX link is down, the power will
shut down, but a few second later the power will restart
automatically.
1
2
3
NO Function Status Description
1
2
3
4FX Speed Set
OFF Disable
Disable
Disable
FX 1000M
FX 100M/1000M
Enable
Enable
Enable
ON
OFF
ON
OFF
ON
OFF
ON
LFP Function1
FX Reset
3
ALS Function
2
(Only for SFP)
- 10 -EN

- 11 -EN
Model: UMC-GA1F2T
ON
1 2 3 4
DIP
NO Function Status Description
1
2
Reserved
Jumbo
Frame
X X
Up to 9KB
FX 100M
FX 1000M
Normal (Up to
1500Bytes)
ON
OFF
3
4FX Speed Set
Disable
EnableON
OFF
OFF
ON
NOTE: If enabled, Layer 2 network trac will not be
forwarded between the two RJ45 ports in the same VLAN.
Port Isolation
1
1

Model: UMC-GA1SC1T-MM/UMC-GA1SC1T-SM
NOTE: LFP (Link Fault Pass Through) Function: If enabled,
when a device is connected to the converter and the TP/ber
line loses the link, the converter's ber will disconnect the link
of transmit.
ALS (Automatic Laser Shutdown) Function: If enabled, the
output power of the SFP transmitter will be automatically shut
down in case of ber break.
FX Reset: If enabled, when FX link is down, the power will
shut down, but a few second later the power will restart
automatically.
1
2
3
NO Function Status Description
1
2
3
4FX Speed Set
OFF Disable
Disable
Disable
FX 1000M
FX 100M/1000M
Enable
Enable
Enable
ON
OFF
ON
OFF
ON
OFF
ON
LFP Function
1
FX Reset
3
ALS Function
2
(Only for SFP)
ON
1 2 3 4
KE
- 12 -EN

Site Environment
Do not operate it in an area that exceeds an ambient temperature
of 40°C.
The installation site should be well ventilated.
Be sure that the Media Converter is level and stable to avoid any
hazardous conditions.
Do note install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water,
heavy dew, and humidity.
- 13 -EN
UMC-GA1F1T/UMC-GA1F2T
Do not operate it in an area that exceeds an ambient temperature
of 50°C.
The installation site should be well ventilated.
Be sure that the Media Converter is level and stable to avoid any
hazardous conditions.
Do note install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water,
heavy dew, and humidity.
UMC-GA1SC1T-MM / UMC-GA1SC1T-SM

Installing
Desk Mounting
TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
Place the media converters on a at, secure surface (such as a desk),
leaving ample space around them for ventilation.
- 14 -EN

- 15 -EN
Rack Mounting (Used with MFMC-12DP 12 Slots Mini
Media Converter Chassis)
1. Install the hanging ears on the left rear side of the media converters
with two screws.
2. Install the media converters in the chassis in sequence (First install
the lower level, then the upper level). Each media converter can be
xed tightly in the chassis by two screws.
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
10/100/1000BASE-T to 100/1000BASE-X
UMC-GA1F1T
Mini Unmanaged Gigabit Ethernet Media Converter
TP/LNK 1000M FX/LNK PWR

UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet MediaConverter
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
3. Place the chassis into the rack. Align the brackets to the side holes on
the rack and use the rack screws to secure the chassis to the rack.
Connecting to the Power
DC
5-12V
- 16 -EN

- 17 -EN
TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
1. Desk Mounting: Connect the power adapters to the media c
onverters and verify that the Power LED lights up.
2. Rack Mounting: Connect the power cord to the media converter
chassis and turn on the power switches on the back of the media
converter chassis. Then verify that the Power LED lights up.
INPUT: AC 100-240V 50/60HZ
FUSE:3.15A
FAN
ON
OFF
MMC-GASFP
10/100/1000Base-TXto1000Base-FX
Mini MediaConverter
MMC-GASFP
10/100/1000Base-TXto1000Base-FX
MiniMedia Converter

Connecting to the RJ45 Port
1. Connect an Ethernet cable to the RJ45 port of the media converter.
S3900-24T4S
1 2 3 4 5 6 7 8 9 10 11 12
13 14
2. Connect the other end of the Ethernet cable to the network device
(switch, PC, router, etc.).
TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
- 18 -EN

18 19 20 21 22 23
- 19 -EN
Connecting to the SFP Port
1. Insert an SFP module into the SFP slot.
2. Connect a ber optic cable to the SFP module. Plug the other end of
the ber optic cable to the ber network.
NOTE:
Both multimode and single mode cablings are
supported. Make sure both side of the SFP module are with the
same media type.
TP/LNK 1000M FX/LNK PWR
UMC-GA1F1T
10/100/1000BASE-T to 100/1000BASE-X
Mini Unmanaged Gigabit Ethernet Media Converter
FX/LNK