FUHR SmartTouch 2.0 Installation guide

WWW.FUHR.DE
www.fuhr.de
Master SmartKey
SmartKey
Smart radio module
Sensor
SmartTouch
2.0
These instructions are to be passed
on by the fitter to the user.
Manuals in further languages, see www.fuhr.de
Access control system with KeylessGo technology
Installation, operating and maintenance manual
MBW26a-EN/04.20-3
Door handles

WWW.FUHR.DE
2
SmartTouch
2.0
SmartTouch 2.0 is a state-of-the-art access control system with KeylessGo technology. It allows the convenient,
keyless opening of front doors equipped with the FUHR motorised locks autotronic 834, autotronic 836 or
multitronic 881. The motor locks are unlocked just by touching the door handle at any position (or alternatively
the sensor) in combination with an active SmartKey.
1.1 Scope of delivery
SmartTouch 2.0 door handles set:
• Smart radio module with connecting cable
• 750 mm extension cable
• Stainless steel door handles with fixing screws
• Master SmartKey
• Installation and operating manual
Optional accessories:
• Mounting set for surface-covering door panels
(Art.-Nr.: VNBZB2460069 / Reference:
VNBZB2460069)
Please order separately:
• User SmartKey (Art.-Nr.: 9366938 / Reference:
VNZ80275)
1.2 Function
SmartTouch allows you the convenient door opening via KeylessGo technology. Therefore it is sufficient to carry
a tuned in SmartKey and to move it. For unlocking the door by the motorised lock, simply touch the door handle
(or sensor). The Smart radio module installed into the door leaf now sends a radio signal, which is received and
answered by the tuned in SmartKey. The Smart radio module checks the opening authorization of the SmartKey
and then unlocks the motorised lock.
If the KeylessGo function is not desired, it can be disabled for each individual SmartKey or completely for all, see
chapter 6.1 for more information. The door can then still be operated via the SmartKey's transmit button.
The SmartTouch door handle has an LED which is controlled by a sensor. This lights up briefly when the door han-
dle is touched and provides orientation. In the darkness the LED lights up permanently. The brightness and size of
the light cone depends on the length of the handle bar and the mounting height.
1.3 Number of tuned in SmartKeys
The memory of the smart radio module is configured for up to 200 SmartKeys. As soon as the memory is full, the
tuning in process is cancelled and no further SmartKey can be paired.
1.4 Power failure
A power failure has no effect on the stored SmartKeys. Opening the door automatically cannot be effected.
We generally recommend the installation of a mechanical locking cylinder in order to ensure that access
is possible at any time independent of the power supply.
1 General information
SmartTouch 2.0 sensor set:
• Smart radio module with connecting cable
• Sensor with 750 mm connecting cable and
fixing screws
• Stainless steel cover
• Master SmartKey
• Installation and operating manual

WWW.FUHR.DE 3
SmartTouch
2.0
2 Functions of the individual components
2.1 SmartKeys
SmartKeys are battery-powered electronic keys. Besides the KeylessGo function all SmartKeys have additionally
4 transmit buttons for remote control. The SmartTouch system differentiates between master SmartKey for tuning
in and deleting, and user SmartKey for door opening.
• Master SmartKey
The master SmartKey included in the scope of delivery is paired with the Smart
radio module at the factory and cannot be changed. With the upper button, Smart-
Keys are tuned in to the Smart radio module, deleted and the radio range is set.
The Master SmartKey cannot be replaced and must therefore
be stored in a safe place! Do not use it for daily door opening, but
only for tuning in and deleting the user SmartKeys.
• SmartKey
The SmartKey is intended for regular door opening via the KeylessGo function or
optionally via the transmit button. The other buttons can be tuned in to additional
Smart radio modules by using the separately available FUHR SmartConnect. This
allows, for example, the control of a garage door or a radio socket.
2.2 Smart radio module
The Smart radio module receives the signal from the SmartKey and transmits it as
an opening impulse to the motorised lock. By pressing the integrated programming
button with green LED light the process of tuning in, deleting and adjusting the
radio range will be started. The memory of the Smart radio module can hold up to
200 SmartKeys. These remain permanently stored even if the operating voltage is
interrupted.
When the Smart radio module is placed into operation (e.g. supplied
with power) for the first time, its electronic components need around
20 seconds to become charged with electrical energy. During this time it
is not possible to open the door using the system’s SmartTouch function.
Pairing and
deleting button
Programming
button with LED
Transmit
button

WWW.FUHR.DE
4
SmartTouch
2.0
3 Installation
3.1 Important installation advices
3.1.1 Screws and drilling holes
I II
Thread cutting fixing
screw
A
Fixing screw with
cable hole
B
45°
93
45°
93
45°
93
98,4
3.1.2 Advices for the door handle installation
PVC profiles
Aluminium profiles
Timber profiles
98,4 98,4
350/1000/1600

WWW.FUHR.DE 5
SmartTouch
2.0
V+ V-
N L
N
L
PE
3.2 Installation of the Smart radio module
Place the Smart radio module on top of the motorised drive mechanism and push it
down carefully until it clicks in place. There are two cables at the back of the Smart
radio module. The short cable "A" is the connecting cable to the door handle or
sensor.
Now connect the cables as follows:
Cable A: The short cable ends in a plug. Connect it with the extension cable of
the door handle or the connecting cable of the sensor. See chapter 3.4.
Cable B: The long 2-core cable ends in a plug. Insert this plug into the plug socket
on the back of the motor. Through this cable, a feedback on the door
status can be sent to the separately available SmartConnect and received
via app.
Cable C: Connect the 3 outgoing cables to the motor plug as follows:
Terminal 4: white cable
Terminal 5: brown cable
Terminal 6: green cable
3.3 Installing the optional LED indicator for the outside of the
door
The control LED (Art.-Nr. 9187229 / Reference: VNZ80067) is used to visually
indicate the locking status of the door. For
installation, connect the plug at the end of the cable of the LED with the plug
socket on the back of the Smart radio module. The motorised lock can then be
inserted into the door leaf profile.
Please ensure that there are no kinks in the cables and that they
are not squeezed or pulled.
B
C
A
3.1.3 Important advice for power supply
For proper functioning of the SmartTouch, a power supply unit with a
passage between the protective earth conductor on the input side (green/
yellow, PE 230V AC) and the earth cable on the output side (black,
12 V DV) is absolutely necessary.
Inform your electrician.
All FUHR transformers (12V DC/230V AC) installed in the door frame are already
carried out for this purpose and can be used without hesitation.

WWW.FUHR.DE
6
SmartTouch
2.0
3.4 Installation of the SmartTouch door handle
3.4.1 On Aluminium, wood or PVC profiles
200/800/1400
Make a cross drill hole for the
Smart radio module on the
bottom screw hole.
1.1
Additional step at timber profiles:
Drill hole for fixing screw
Avoid damage of lockcases and cables
at all costs!
Plug all cables together.
For the correct connectionof the
smart radio module see chapter
3.2.
4.
4.
Connecting
cable
Smart radio
module cablel
Cable to motor
1.
3.
2.
SW13
Ø 8,5 mm
Ø 8,5 mm
Screw drill holes with 8,5 mm Ø on desired
position.
We recommend choosing the drill hole
positions so that the centre of the door handle
is at 1,300 mm. The position of the lockcases
or a sufficient thickness of the profile must be
considered, see picture I and II in chapter 3.1.1.
On timber profiles there has to be a cross drill addi-
tionally. See step 1.1 in the picture below.
Pre-cut the thread with fastening screw A, please
grease the screw beforehand (for PVC profiles with
steel reinforcement please pre-cut with an M10
tap), unscrew it and screw in fixing screw B.
Screw and tighten fixing screw A.
1.
2.
3.
1.1

WWW.FUHR.DE 7
SmartTouch
2.0
Pull extension
cable trough
the cable hole
of the fixing
screw B.
Please ensure that there are no kinks
in the cables and that they are not
squeezed or pulled.
5.
5.
Plug the extension cable to the cable of
the door handle electronics and push it
back into the door handle or profile as
far as possible.
Carefully put the door handle on
the fixing screws.
Tighten the grub screws
of the door handle.
6.
6.
7.
7. 8.
8.
SW 3

WWW.FUHR.DE
8
SmartTouch
2.0
3.4.2 On surface covering door panels
For installation on surface covering doopr panels you need FUHR's mounting set Art.-Nr. 9367768 / Referenz:
VNBZB2460069.
10 mm
A
B
R3
45 mm
20 mm
45 mm
> 30 mm
Ø 40 mm
26 mm
Reserve loop
Cable to
Smart radio device
Put both panel halves on top of each other and
drill both holes on the desired handle height with
10 mm Ø.
1.
For both holes, mill a 45 x 45 mm pocket with
20 mm depth (6 mm milling cutter). Drill hole and
milling have the same centre.
3.
Pass the extension cable through the protective tube
and put the reserve loop into the hole of 40 mm Ø.
Push the end of the cable through the centre of the
mounting profile.
5.
Remove the upper half of the panel and mill a
26 mm deep hole with 40 mm Ø at hole B.
The panel needs to have a thickness of at least
30 mm.
2.
Press the mounting profile in pockets Aand Binto
the filling foam glue.
6.
Hole for the
reserve loop
B
A
B
A
10 mm
Sizes in cross-section
Drill in the centre of pocket Ba lateral cable hole
with 10 mm Ø into the door panel and insert the
supplied protective tube.
4.
Passage in the direction of
the Smart radio module
Ø10 mm
minimum
34 mm
9 mm
10 mm
20 mm

WWW.FUHR.DE 9
SmartTouch
2.0
SW13
Place the loose panel half on top, insert the cable
through the hole and glue both panel halves
together.
7. Pull the cable through the supplied fixing screw with
cable hole and screw it in (B). Afterwards screw in the
other fixing screw in hole A.
8.
B
A
SW 3
Plug the extension cable to the electricity cable of
the handle and push it back into the door
handle or the profile as far as possible.
Screw in and fix the grub screws of the handle.
11.
Carefully put the door handle on the fixing screws.
Be careful not to
pinch or kink the
cable.
10.
9.

WWW.FUHR.DE
10
SmartTouch
2.0
200
Cable A
Connecting cable
stainless steel
cover
Fit the cover with
the recess pointing
downwards
Hole Ø 8 mm
for connecting
cable
3.5 Installing the SmartTouch sensor
The sensor is made of a black plastic casing with connecting cable and a stainless steel cover.
Fit the sensor to the outside of the door leaf using the screws supplied. Finally the stainless steel cover is glued on.
For installing the sensor proceed as follows:
1. Mill a 20 x 20 mm opening 200 mm above the door handle hole into the outer profile wall of the door leaf.
Deburr the milling carefully.
2. Guide the connection cable through the opening downwards to the milling of the motor drive.
3. Plug the connecting cable to cable A of the Smart radio module.
4. Screw in the plastic casing of the sensor with the supplied screws into the profile.
5. Clean the adhesive areas of the plastic casing to ensure a perfect hold.
6. Now remove both strips of the protective film from the back of the stainless steel cover.
7. Finally, press the cover firmly onto the plastic casing.
R4
20 mm
35mm
plastic
casing
Tapped drill holes in
aluminium profile for
M3x8: 2,6 - 2,7 mm
M3x8 for
Aluminium and
PVC profiles
3x20 for timber
profiles
20 mm
Pocket:
at least 25 mm
deep

WWW.FUHR.DE 11
SmartTouch
2.0
4 Tuning in and deleting SmartKeys
Note: If you exceed the 20 seconds or use the wrong master SmartKey, the tuning in process
will be cancelled.
4.1 Tuning in the SmartKeys
For security reasons, we recommend to clear the memory of the Smart radio module when first
placing the system into operation. This prevents unauthorised persons from tuning in a Smart
Key. Delete all SmartKeys as described in chapter 4.3 and start afterwards with the tuning in
process.
1 x
2 x
within 20 Sek.
within 20 Sek.
1. Carefully press the programming button on the Smart radio module
for approx. 1 second.
The green LED of the Smart radio module lights up for approx.
2 seconds and then starts flashing slowly.
2. Press the tuning in and opening button on your master SmartKey
within 20 seconds once.
The green LED of the Smart radio module lights up for 2 seconds and
then starts flashing at one-second intervals.
3. Press the transmit button on the SmartKey to be tuned in within
20 seconds, twice.
The green LED of the Smart radio module lights up for 4 seconds and
afterwards turns off automatically.
4. The tuning in process is finished and the SmartKey can be used for
door opening.
Advice: If there is a SmartTouch door handle installed, it beeps by
touching and the door can be opened.
ca. 1 sec.

WWW.FUHR.DE
12
SmartTouch
2.0
You can remove the opening authorisation of each SmartKey individually. To delete a single SmartKey from the
memory of the Smart radio module, proceed as follows:
4.2 Delete individual SmartKeys
1 x
within 20 sec.
1. Carefully press the programming button on the Smart radio module
for at least 3 seconds.
As soon as the push-button is released, the green LED of the Smart
radio module starts flashing rapidly.
2. Press the tuning in and opening button on your master SmartKey
within 20 seconds once.
The green LED of the Smart radio module lights up for 2 seconds and
then flashes rapidly again.
3. Press the transmit button on the user SmartKey you want to delete,
within 20 seconds once.
The green LED of the Smart radio module lights up for 4 seconds and
afterwards turns off automatically.
4. The deleting process is completed. Check by pressing the transmit
button on the user SmartKey if the deleting process was successful.
1 x
within 20 sec.
> 3 sec.

WWW.FUHR.DE 13
SmartTouch
2.0
4.3 Deleting all SmartKeys
You can remove the opening authorisation for all SmartKeys at the same time. The master SmartKey cannot be
deleted. To delete all SmartKeys from the memory of the Smart radio module, proceed as follows:
1 x
within 20 sec.
> 3 sec.
1. Carefully press the programming button on the Smart radio module
for at least 3 seconds.
As soon as the push-button is released, the green LED of the Smart
radio module starts flashing rapidly.
2. Press the tuning in and opening button on your master SmartKey
within 20 seconds once.
The green LED of the Smart radio module lights up for 2 seconds and
then flashes rapidly again.
3. Now carefully press the programming button on the Smart radio
module for at least 3 seconds once again.
As soon as the push-button is released, the green LED lights up for
4 seconds and afterwards turns off automatically.
4. The deleting process is completed. Check by pressing the transmit
button on one user SmartKey if the deleting process was successful.
> 3 sec.

WWW.FUHR.DE
14
SmartTouch
2.0
15
5 Radio range
5.1 Range of the KeylessGo function
The distance in which a SmartKey responds to the radio signal of the Smart radio module varies significantly with
environmental conditions. If the SmartKey is significantly further away than 1 meter from the door, it usually does
not respond. Electrically conductive objects e.g. can increase this distance. The requirement for a SmartKey to
respond after touching the handle bar/sensor is in any case that it is in motion.
Please note that SmartKeys can also be detected from the Smart radio module when you are
inside the building under the following conditions:
1. The SmartKey is located inside the KeylessGo radio range (please determine this area individ
ually at your own door) and
2. within the last 3 seconds the SmartKey was in motion.
Note the additional security functions in chapter 6.
For safety reasons, we recommend to lay the SmartKey down when you are inside the building.
The motion sensor is then deactivated after 3 seconds and unauthorised opening of the door is
no longer possible.
5.2 Adjusting the range
The KeylessGo range between the Smart radio module and the SmartKeys depends on the door material is there-
fore adjustable.You can increase this range by 2 steps, for example, if the KeylessGo door opening often does not
work.
To change this radio range, proceed as follows:
1. Carefully hold the programming button of the Smart radio module for longer than 10 seconds. The radio
range is indicated by the number of periodic LED flashes of the smart radio module:
1x flashing = smallest radio range
3x flashing = range by delivery
9x flashing = maximum radio range
10x flashing = KeylessGo is disabled for all SmartKeys!
2. Each time the programming button of the Smart radio module is pressed again, the radio range increases
to another level. The maximum radio range is reached by 9x flashing. As soon as the LED flashes 10 times
the KeylessGo function is deactivated for all SmartKeys. By pressing again you will get back to level 1 with
the smallest radio range.
3. After setting the desired radio range, press and hold the programming button on the Smart radio module
again for at least 10 seconds to exit the setting mode.
5.3 Radio range of the remote control function
The radio range of the 4 remote control buttons strongly varies with the environmental conditions. The range is at
least 10 m and cannot be changed. However, depending on the door material this range varies. Objects between
the SmartKey and the Smart radio module may reduce this distance.

WWW.FUHR.DE 15
SmartTouch
2.0
WWW.FUHR.DE15
6 Security functions
6.1 Manually turning on/off the KeylessGo function
You can switch the KeylessGo function – in other words the option of opening the door by touching the door
handle or sensor – on or off for each SmartKey separately. To enable or disable this function, simply press the
transmit button on the respective SmartKey for at least 5 seconds. The Smart radio module uses acoustical and
optical signals to indicate a change of mode:
Switching off = 2x long glow/beep Switching on = 2x short glow/beep
If KeylessGo is disabled, you can still open the door using the transmit button on the SmartKey!
6.2 Automatically switching off function of the SmartKeys
For safety reasons, all SmartKeys are fitted with a motion sensor. If a SmartKey is not moved for 3 seconds, it
automatically switches off by itself. If the SmartKey is within the detection radius of the Smart radio module, the
deactivation prevents unauthorized door opening via KeylessGo. Furthermore the deactivation mode saves battery
power. You can activate the sensor again by moving the SmartKey and open the door, as usual, via KeylessGo
function.
6.3 Automatical blocking times
For safety reasons, after every complete opening of the door (tappet contact and contact surface do not touch)
and every closing, the possibility to oppen via KeylessGo is always blocked automatically for 5 seconds. After a
motorised opening touching the door hanlde or sensor it will be disabled for 15 seconds. This prevents an unau-
thorised opening of the door. Please await this 5 or 15-second period for using the KeylessGo function again or
just use the transmit button on the SmartKeys.

WWW.FUHR.DE
16
SmartTouch
2.0
16
Situation Solution
The LED in the bottom of the door handle does
not light up by touching the handle?
Check if the door handle is connected correctly to the ca-
ble of the Smart radio module (chapter 3, cable A) and
that a suitable main adapter (Chapter 3.1.3) has been
connected in between.
The LED of the SmartKey does not flash by tou-
ching the door handle?
Please make sure that the SmartKey is in motion. Check
if the battery is discharged (chapter 8.1). Make sure that
KeylessGo is activated for this SmartKey (chapter 6.1).
Does the Smart radio module beep approx.
6 seconds after touching the door handle five
times?
(Please note that, depending on the door ma-
terial, the beeping could be very low!)
There is no authorised SmartKey found. Check if the key
was tuned in (chapter 4.1). Change the position of the
SmartKey to ensure the radio range. To do so e.g. take the
SmartKey in your hand. Afterwards you may increase the
radio range (chapter 5.2.).
Does the LED only light up by touching the
handle support?
Check if a suitable main adapter has been connected in
between (chapter 3.1.3).
Does the LED only light up by touching the door
handle and door frame?
Check if a suitable main adapter has been connected in
between (chapter 3.1.3).
If the motorised lock does not open when touching the door handle or the sensor, please check first whether
one of the safety functions listed in chapter 6 is active.
7.1 Trouble-shooting
If the motorised lock cannot be opened when touching the door handle or sensor please work through the follow-
ing points using a SmartKey step by step:
First, briefly press the opening button of the SmartKey, to open the motorised lock per radio signal.
• If the motorised lock does not open with the SmartKey, please check the following points:
– Is the Smart radio module connected to the motor plug correctly?
– Was the SmartKey tuned in to the Smart radio module (see chapter 4)?
– Were any cables damaged when the system was installed in the door leaf?
– Does the motorised lock have power access?
– Is the SmartKey battery flat? (If there is still charge in the battery, the SmartKey will light up once when the
transmit button is pressed briefly.)
• If the motorised lock opens by pressing the opening button of the SmartKey, check the KeylessGo function.
Please consider the blocking times between the door openings.
7 Errors and failures

WWW.FUHR.DE 17
SmartTouch
2.0
8.1 Charge level of the SmartKey battery
If SmartKey batteries are low, this will reduce the radio range. The SmartKey measures the amount of charge
remaining in the battery by pressing its transmit button. If the battery is too low, the LED of the SmartKey flashes
3 times when its transmit button is pressed. If this happens, please replace the battery promptly. All stored data
remain saved when changing the battery.
Please change the batteries in time, if the batteries are completely empty you cannot open the
door with the SmartKey anymore.
8.2 Battery change
The SmartKey is operated by a battery type CR2032. Immediately it is ready for use just after changing the battery.
Please proceed as follows when changing the batteries:
1. Insert a narrow object (such as a flat-head screwdriver) into the slot at the back of the SmartKey and gently
lever the cover up.
2. Replace the battery, making sure the polarity is correct (the positive pole must be visible).
3. Close the case.
Batterie
CR2032
2.1.
8 Battery

WWW.FUHR.DE
18
SmartTouch
2.0
9 Safety, maintenance and care instructions
• All components must be protected against moisture. They are not suitable for use in areas with high humidity
or for exposure to chemical substances.
• Only genuine FUHR accessories may be used.
• No liability will be accepted in case of incorrect installation or operation.
• Casings and cables must be protected against mechanical damage.
• Damaged or defective components must be taken out of operation and replaced.
• The Smart radio module is maintenance-free.
• If the transmission range of a SmartKey deteriorates, please change its battery.
9.1 Disposal information
Old devices and batteries are not allowed to be disposed with household waste!
Dispose of the old devices via a collection point for electronic waste or via your specialist shop.
Dispose of the old batteries in a recycling container for used batteries or via your specialist shop.
Dispose of the packaging material in the collection container for cardboard, paper and plastics.

WWW.FUHR.DE 19
SmartTouch
2.0
10.1 Smart radio module
Frequency: 868,92 MHz
Modulation: FSK
Security: Rolling-Code | AES - 128 bit | master key principle
Anti-collision check: Yes
Antenna: On-board
Power supply: 12VDC
Current consumption: 0,1 bis 50 mA
Activity indicator: Green light-emitting diode
Temperature range: 5°C to 50°C, non-condensing
Dimensions: 43 x 40 x 15 mm
Protection rating: IP 20
Switching impulse: Potential-free
10.2 Master SmartKey and SmartKey
Frequency: 868,92 MHz / 125 kHz
Modulation: FSK
Security: Rolling-Code | AES – 128 bit
Channels: 4
Power supply: 1x 3V battery CR 2032
Temperature range: 5°C to 50°C, non-condensing
Dimensions: 61,5 x 37 x 10,5 mm
10.3 SmartTouch door handle
Material: High-quality stainless steel
Length: 350 mm, 1000 mm and 1600 mm
Supports: 2 supports, 1600 mm length optionally also with 4 supports
Designs:
Square or round door handles with straight supports for
mounting on the panels;
round door handles with inclined supports
Power supply: 12 VDC
10 Technical specifications

SmartTouch
2.0
CARL FUHR GmbH & Co. KG
Carl-Fuhr-Straße 12 D-42579 Heiligenhaus
Tel.: [phone] Fax: [phone]
www.fuhr.de · [e-mail]
All image, product, dimension and design information in these instructions corresponds to the current state of development on the day of going to press. This product is subject to a continuous improvement process at FUHR and is constantly adapted to technical progress. In the interest of your satisfaction we must reserve the right to make changes to the product. Model and product claims cannot be asserted. The latest version of the instructions can be found on our website www.fuhr.de.