Fujitsu D3030 User manual

Technical Manual - English
System Board D3030
for BX920 S2
Technical Manual
Edition March 2011

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
email: [email protected].
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5694-004.fm
Copyright © 2011 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

D3030 (BX920 S2) Technical Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the product
is used in a hot environment. The customer shall bear the cost of replacing
replaceable components which have exceeded their operating life. Note that
these are only guidelines, and do not constitute a guarantee of trouble-free
operation during the maintenance support period.
High safety use
This product has been designed and manufactured for general uses such as
general office use, personal use, domestic use and normal industrial use. It has
not been designed or manufactured for uses which demand an extremely high
level of safety and carry a direct and serious risk to life or body if such safety
cannot be ensured.

Technical Manual D3030 (BX920 S2)
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5694-004.fm
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance control
in weapons systems (hereafter, "high safety use"). Customers should not use
this product for high safety use unless measures are in place for ensuring the
level of safety demanded of such use. Please consult the sales staff of Fujitsu if
intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market:
About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://primeserver.fujitsu.com/primergy/harddisk/

D3030 (BX920 S2) Technical Manual
Only for the Japanese market:
IAlthough described in this manual, some sections do not apply to the
Japanese market. These options and routines include:
– CSS (Customer Self Service)
– Replacing the lithium battery

Technical Manual D3030 (BX920 S2)
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5694-004.fm

D3030 (BX920 S2) Technical Manual 7
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Notational conventions . . . . . . . . . . . . . . . . . . . . . 9
2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 CE certificate of conformity . . . . . . . . . . . . . . . . . . 14
2.3 Environmental protection . . . . . . . . . . . . . . . . . . . 15
3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.1 Memory speed . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . 29
3.4 Temperature/system monitoring . . . . . . . . . . . . . . . 29
3.5 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5.1 Internal indicators . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5.2 External indicators . . . . . . . . . . . . . . . . . . . . . . . . 32
3.6 Interfaces, connectors and DIP switch . . . . . . . . . . . . 33
3.7 Settings with switches and jumpers . . . . . . . . . . . . . 34
4 Replacing the lithium battery . . . . . . . . . . . . . . . . . 37

© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5689-004.fm

D3030 (BX920 S2) Technical Manual 9
1 Introduction
This technical manual describes the D3030 system board, which can be
equipped with two processors.
For additional driver information (if available), refer to the supplied DVDs (see
Installation DVD of ServerView Suite - ServerView Software Products).
You will find further information about the BIOS setup in the "D3030 BIOS Setup
Utility for PRIMERGY BX920 S2 Server Blade" manual.
IPRIMERGY manuals are available in PDF format on the ServerView
Suite DVD 2. The ServerView Suite DVD 2 is part of the ServerView Suite
supplied with every server.
PRIMERGY Abbreviations and Glossary can also be found on the ServerView
Suite DVD 2.
1.1 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5690-004.fm

D3030 (BX920 S2) Technical Manual 11
2 Important notes
This chapter provides safety instructions which you must observe when
handling your server.
VCAUTION!
With the system board installed you must open the system to access the
system board. How to access the system board of your system is
described in the appropriate service supplement (except for the
Japanese market).
When handling the system board, refer to the specific notes on safety in
the operating manual and/or service supplement for the respective
server.
2.1 Notes on safety
VCAUTION!
●The actions described in these instructions should only be performed
by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.
●Transport the device only in the antistatic original packaging or in
packaging that protects it from knocks and jolts.
●Only install expansions that are allowed for the system board. If you
install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are approved for installation
can be obtained from our customer service center or your sales
outlet.
●The warranty expires if the device is damaged during the installation
or replacement of system expansions.

12 Technical Manual D3030 (BX920 S2)
Notes on safety
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5691-004.fm
VCAUTION!
●Components can become very hot during operation. Ensure you do
not touch components when making extensions to the system board.
There is a danger of burns!
●Transmission lines to peripheral devices must be adequately
shielded.
●Ethernet cabling has to comply with EN 50173 and EN 50174-1/2
standards or ISO/IEC 11801 standard respectively. The minimum
requirement is a Category 5 shielded cable for 10/100 Ethernet, or
Category 5e for Gigabit Ethernet.
●Never connect or disconnect data transmission lines during a storm
(risk of lightning hazard).
Batteries
VCAUTION!
●Incorrect replacement of batteries may lead to a risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (this information doesn’t apply to
the Japanese market).
It is essential to observe the instructions in chapter "Replacing the
lithium battery".

D3030 (BX920 S2) Technical Manual 13
Notes on safety
Modules with Electrostatic-Sensitive Devices
Modules with electrostatic-sensitive devices are identified by the following
sticker:
Figure 1: ESD label
When you handle components fitted with ESDs, you must always observe the
following points:
●Switch off the system and remove the power plugs from the power outlets
before installing or removing components with ESDs.
●You must always discharge static build-up (e.g. by touching a grounded
object) before working with such components.
●Any devices or tools that are used must be free of electrostatic charge.
●Wear a suitable grounding cable that connects you to the external chassis of
the system unit.
●Always hold components with ESDs at the edges or at the points marked
green (touch points).
●Do not touch any connectors or conduction paths on an ESD.
●Place all the components on a pad which is free of electrostatic charge.
IFor a detailed description of how to handle ESD components, see the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).

14 Technical Manual D3030 (BX920 S2)
CE certificate of conformity
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5691-004.fm
Instructions for handling boards
●The specific instructions in the service article for the respective end device
must be observed when installing and removing the board.
●Disconnect the device plug from the shock-proof socket before carrying out
any work on an installed board.
●Exercise extreme care when installing and removing all boards.
Take care not to tilt boards; they must be installed perfectly straight.
If they are incorrectly handled, the boards and the components on them, or
the other components (e.g. EMI spring contacts) and conductors can be
damaged.
●Handle all locking mechanisms (engaging lugs and centering pins) carefully
when installing/removing the board or components (e.g. memory modules,
processors).
●Never use sharp objects (screwdrivers) as levers.
2.2 CE certificate of conformity
The board complies with the requirements of the EC directives
2004/108/EC regarding “Electromagnetic Compatibility” and
2006/95/EC “Low Voltage Directive”. This is indicated by the CE
marking (CE = Communauté Européenne).
Compliance was tested in a typical PRIMERGY configuration.

D3030 (BX920 S2) Technical Manual 15
Environmental protection
2.3 Environmental protection
Environmentally-friendly product design and development
This product has been designed in accordance with the Fujitsu standard for
"environmentally friendly product design and development". This means that
key factors such as durability, selection and labeling of materials, emissions,
packaging, ease of dismantling and recycling have been taken into account.
This saves resources and thus reduces the harm done to the environment.
Further information can be found at:
–http://ts.fujitsu.com/products/standard_servers/index.html (for the EMEA market)
–http://primeserver.fujitsu.com/primergy/concept/ (for the Japanese market)
Energy-saving information
Devices that do not need to be constantly switched on should be switched off
until they are needed as well as during long breaks and after completion of work.
Packaging information
This packaging information doesn’t apply to the Japanese market.
Do not throw away the packaging. You may need it later for transporting the
system. If possible, the equipment should only be transported in its original
packaging.
Information on handling consumables
Please dispose of printer consumables and batteries in accordance with the
applicable national regulations.
In accordance with EU directives, batteries must not be disposed of with
unsorted domestic waste. They can be returned free of charge to the
manufacturer, dealer or an authorized agent for recycling or disposal.

16 Technical Manual D3030 (BX920 S2)
Environmental protection
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5691-004.fm
All batteries containing pollutants are marked with a symbol (a crossed-out
garbage can). They are also marked with the chemical symbol for the heavy
metal that causes them to be categorized as containing pollutants:
Cd Cadmium
Hg Mercury
Pb Lead
Labels on plastic casing parts
Please avoid sticking your own labels on plastic parts wherever possible, since
this makes it difficult to recycle them.
Returns, recycling and disposal
Please handle returns, recycling and disposal in accordance with local
regulations.
Details regarding the return and recycling of devices and consumables within
Europe can also be found in the "Returning used devices" manual, via your local
Fujitsu branch or from our recycling center in Paderborn:
Fujitsu Technology Solutions
Recycling Center
D-33106 Paderborn
Tel. [phone]
Fax [phone]
The device must not be disposed of with domestic waste. This
device is labeled in compliance with European directive
2002/96/EC on waste electrical and electronic equipment (WEEE).
This directive sets the framework for returning and recycling used
equipment and is valid across the EU. When returning your used
device, please use the return and collection systems available to
you. Further information can be found at
http://ts.fujitsu.com/recycling.

D3030 (BX920 S2) Technical Manual 17
3 Features
3.1 Overview
Processors
– 1 or 2 Intel®Xeon®processors of the 5500 and 5600 series
– 2 processor sockets LGA1366 for Intel®Xeon®processors
– Integrated memory controller (DDR3)
– 32 KB L1 cache (on-die data cache per core)
– 32 KB L1 cache (on-die instruction cache per core)
– 256 KB L2 cache (mid-level per core)
– Up to 12 MB on chip shared L3 cache (among all cores)
– 2x Intel®QuickPath Interconnect with up to 6,4 GT/s in each direction
Main memory
– 9 slots for main memory DDR3 1066 / 1333 single-, dual- or quad-ranked
DIMM memory modules with 2 GB, 4 GB, 8 GB and 16 GB
– Buffered and unbuffered DIMMs with ECC are supported, mix of memory is
not permitted
– Maximum 144 GB of memory
– Minimum 2 GB (1 memory module)
– Maximum 32 Gbit/s band width (DDR3)
– CPU0 has 2 DIMM slots for memory rows per channel, CPU1 has 1 DIMM
slot for memory row per channel
– ECC multiple-bit error detection and single-bit error correction
– Memory scrubbing functionality
– Single Device Data Correction (SDDC) function (Chipkill™)
Chips on the system board
– Intel®5500 chipset
– Intel®ICH10 Base
– 2x Intel®82575EB dual-port Gigabit Ethernet controller
– Hard disk controller LSI1064E SAS for 2 SAS hard disks
– iRMC S2 (integrated Remote Management Controller) with integrated
graphic controller
– 2 MB Flash ROM
– 32Mx16-667 DDR2 SRAM for iRMC S2
– ADT7462 temperature/system monitoring controller

18 Technical Manual D3030 (BX920 S2)
Overview
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5692-004.fm
Graphic
– Integrated VGA controller with PCIe x1 interface (PILOT-II)
– 16 MB graphic memory available via driver
LAN – Ethernet controller
– 2x Intel®82575EB dual-port 10/100/1000 Mbit/s Base-T Ethernet controller
– 1x BCM5221 for iRMC S2
Storage devices
– 2x SAS (1.5 Gbit/s) or 2x SATA
– 2.5“ drive slide-in modules are supported
– UFM (USB Flash Module)
External connectors (via Y cable)
– 4x USB 2.0 interfaces at the front side
– 1x serial interface at the front side
–1xVGA
Internal connectors
– 1x video connector (VGA) at the front side
– 1x universal USB port for 4 USB connectors at the front side
– 1x UFM connector (USB Flash Module connection) for USB Flash ROM
– 9x slots for DDR3 memory modules
– Power supply (12 V and 5 V auxiliary supply)
iRMC S2 server management controller
– Basic features: Temperature monitoring, System Event Log and ASR&R
(Automatic Server Reconfiguration and Restart)
–PDA
– Global Error/CSS/ID LED
– Pre-failure warranty for memory
– HD LED support (SAS, SATA)
– Inventory Identification Control
– CSS functionality
– Energy consumption control
– Console redirection (text console)
– Graphic console redirection (Advanced Video Redirection - AVR)
– Provision of remote memory media (Remote Storage)

D3030 (BX920 S2) Technical Manual 19
Overview
Security features
– Password protection for system and BIOS
– BIOS restore support
– Virus protection through Flash Write Protection
Energy saving functions
– ACPI (States S0, S1, S4, S5)
– On/Off/Idle state/Reactivate via power switch
– Switch on and off via software
– Reactivate the server from standby via RTC, external serial ports, LAN, PCIe
controller and iRMC S2
– Switch on the server via the power switch, external serial ports, LAN, PCIe
controller and iRMC S2
BIOS features
–AMI
– SMBIOS 2.5 (DMI)
– MultiProcessor specification
– Server Hardware Design Guide
–WfM
– ACPI support
– LSI SAS/RAID BIOS
– USB keyboard/mouse
– boot possible from:
– hard disk (SATA, SAS, SCSI, USB)
– USB stick
– CD/DVD (SATA, SAS)
–LAN
– console redirection support
– OEM logo
– CPU, memory disable
– Mirroring and Spare memory support
Environmental protection
Battery in holder for recycling
Form factor, slot compatibility list
– 491 x 200mm

20 Technical Manual D3030 (BX920 S2)
Overview
© cognitas. Gesellschft für Technik-Dokumentation mbH 2011 Pfad: C:\Programme\FCT\tim_app\tim_local\work\WALTER\OBJ_DOKU-5692-004.fm
– ACPI 2.0, OnNow, PCI Express 2.0, LPC 1.1, WfM 2.0, SHDG 3.0, MPS 1.4,
IPMI 1.5, PCI SHPC 1.0 and PCI Express card
electromechanical specification rev. 1.0, USB2.0, SATAII 2.0
CSS (Customer Self Service)
This system board supports the CSS functionality. You will find a description of
CSS functionality in the operating manual of your server.
IThis feature is not available for the japanese market.
UFM (optional)
By the manufacturer the system board is equipped with a slot for an UFM (USB
Flash Module). The module can be used as optional memory for software
(e.g. VMware) or as a software dongle.
Trusted Platform Module (TPM)
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
BIOS manual).
VCAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.