Fujitsu FI 4220C - Document Scanner User manual

Release the Shipping Lock
2
Make sure to slide the shipping lock in place (located on the bottom of
the scanner) to secure the internal carrier unit during transportation.
After transporting and placing the scanner, tilt the scanner (approx. 30
degrees) and release the shipping lock.
See the "fi-4220C Image Scanner Operator's Guide" for further details.
Check the scanner and accessories
1
Confirm that all of the following items are included.
Scanner ADF paper chuteUSB interface cable
fi-4220C Image Scanner
Operator's Guide
Continued on next page
Carefully read the "fi-4220C Image Scanner Operator's
Guide" before using this product.
Particularly read and understand the "Safety Precautions"
before using this product.
Quick Installation Guide
Attach the ADF paper chute
3
1. Holding the ADF paper chute, insert it so that the two tabs on the chute
slot into the holes on the rear of the scanner.
Attach the ADF paper chute so that the side with the side guides is face up.
Connect the USB interface cable, SCSI interface cable and the AC cable
4
1. Connect either the USB interface cable or the SCSI interface cable.
When using WindowsR95, Windows NT R4.0,connect the SCSI interface cable.
Connecting the USB interface cable
1
Connect the PC end of the USB interface cable to the PC.
2 Connect the scanner end of the USB interface cable to the scanner.
Connecting the SCSI interface cable
1 Connect the PC end of the SCSI
interface cable to the PC.
2 Connect the scanner end of the SCSI interface cable to the scanner.
3 Check the SCSI ID switch.
The SCSI ID switch is set to No. 5. If another device has the same ID then change the SCSI
ID. Refer to the "fi-4220C Image Scanner Operator's Guide" for information about the
procedure to change the SCSI ID.
2. Connect the AC adapter with the AC Cable, and then connect it to the DC inlet on the
Scanner.
Caution
Confirm that the power of PC and the image scanner device is
turned off.
•When using WindowsR98, WindowsRMe, WindowsR2000
or WindowsRXP, perform the procedure in step to
complete installation.
•When using WindowsR95 or Windows NT R4.0, perform the
procedure in to complete the installation.
• It is necessary to separately purchase a SCSI interface cable and a
SCSI card which are available commercially. See "fi-4220C Image
Scanner Operator's Guide" for details.
• Connect the scanner so that it is the terminator SCSI device.
3. Insert the AC cable into the power outlet.
Next, install the FUJITSU TWAIN32 Scanner driver.
Caution
P3PC-E057-03EN
Install FUJITSU TWAIN32 Scanner driver
5-a
WindowsR98,WindowsRMe,WindowsR2000,WindowsRXP
Install the mini-driver first, and then the TWAIN data source.
If the old version of FUJITSU TWAIN32 Scanner driver has been installed on your personal computer, refer to the
"Scanner Utility for Microsoft
RWindows RUser's Guide" on the Scanner driver CD-ROM, and update the mini-driver.
Caution
The Windows
RXP screen samples are shown below. The screen
and operations will differ slightly depending on the OS that is
being used.
Preparation
Confirm that the Scanner is connected to your personal computer
with the USB interface cable or SCSI interface cable.
Installing the mini-driver
1. Turn on the power by pushing the power switch on the scanner's control
panel.
The green LED on the control panel lights. The Function No. display
shows to the order "8","P","0","1". When Function No. display
reaches "1" the scanner is ready.
2. Turn on your personal computer and log on to WindowsR.
When using WindowsR2000 or WindowsRXP log on as an
administrator . The "Found New Hardware Wizard" dialog box is
displayed.
3. Check "Install from a list or
specific location (Advanced)",
then click [Next].
For WindowsRMe, check "Specify the location of the driver
(Advance)", then click [Next].
For WindowsR2000 and WindowsR98, clicking on [Next] the select
search method screen is displayed.
• For WindowsR98, select "Search for the best driver for your
devise. (Recommended)" then click [Next].
• For WindowsR2000, select "Search for a suitable driver for my
device (Recommended)" then click [Next].
4. Insert the Scanner driver CD-ROM
5. Select "Search for the best
driver in these locations".
Check "Include this location in
the search:" then specify
D:\Driver2 (When your CD-
ROM is the D drive). After that
click [Next].
For WindowsR98, just check "Specify a location:" then specify
D:\Driver2 (When your CD-ROM is the D drive). After that click
[Next].
For WindowsRMe, select "Search for the best driver for your
device." Check "Specify a location" then specify D:\Driver2 (When
your CD-ROM is the D drive). After that click [Next].
For WindowsR2000, just check "Specify a location" and then in the
next screen specify "Copy manufacturer's files from:" then specify
D:\Driver2 (When your CD-ROM is the D drive), then click [OK].
ADF paper chute
tab
Side guide
Lock Release
DC inlet
USB interface cable(*1)
SCSI interface cable(*1)
AC cable(*2)
Refer to the "fi-4220C Image Scanner Operator's Guide" when you would like
to know more about the scanner.
Refer to the "Scanner Utility for Microsoft RWindows RUser's Guide" on the
Scanner driver CD-ROM when you would like to know more detailed information
about the FUJITSU TWAIN32 Scanner driver installation.
SCSI interface
connector
USB interface
connector
*1) Connect to your PC.
*2) Connect to the power outlet.
fi-XXXXXXXXXXXXX
FUJITSU TWAIN32
Scanner Driver
CD-ROM
Manual
CD-ROM
Adobe RAcrobat R5.0
CD-ROM AC adapterAC cable
fi-4220C Quick Installation Guide
FUJITSU ISIS Scanner Driver
Quick Installation Guide
FUJITSU ISIS
Scanner Driver
CD-ROM

Installation end
Hint
7
Install FUJITSU TWAIN32 Scanner driver
5-b
6
Install Image Capturing Software Utilities "ScandAll 21" for Microsoft RWindows R
Confirm whether the scanner works normally, as follows.
1. Place a document on the ADF paper chute.
For details on how to load documents, see " 3 BASIC SCANNER
OPERATIONS" in the "fi-4220C Image Scanner Operator's Guide"
2. Start ScandAll 21.
In the start menu select [Program] then [Scanner Utility for
Microsoft Windows] then [ScandAll 21] in that order.
3. Specify the scanner
you are using.
Select [Select Source]
from the [Scan] menu
in ScandAll 21.
The following dialog is displayed.
- In case of Windows
R
98, Windows
R
Me,
Windows
R
2000, and Windows
R
XP,
Select "FUJITSU fi-4220Cdj".
- In case of Windows
R
95,
and Windows NT
R
4.0,
Select "FUJITSU TWAIN32".
And then Click [Select].
4. Click [Scan To View] in the toolbar.
5. In [TWAIN Driver] (Scan
conditions setting screen) set
the scan resolution, paper size
and other scanning conditions,
and click the [Scan] button.
For details on settings in the
[TWAIN Driver] dialog box, refer
to the "Scanner Utility for
Microsoft RWindows RUser's
Guide" on the Scanner driver
CD-ROM.
The document is scanned and
the image is displayed on the
ScandAll 21 screen.
If the document can be scanned then setup has been successfully finished.
For various scanning operations not mentioned here,
see " 4 SCANNING VARIOUS TYPES OF DOCUMENTS" in the"fi-4220C
Image Scanner Operator's Guide".
See"ScandAll 21 Help" for information about ScandAll 21 functions and
operations.
WindowsR95,Windows NT R4.0
Refer to the "Scanner Utility for MicrosoftRWindowsRUser's Guide" on the Scanner driver CD-ROM when you would like to know more detailed
information about the FUJITSU TWAIN32 Scanner driver installation.
Preparation
1. Confirm that the SCSI adapter is attached to your personal computer.
2. Confirm that SCSI driver and ASPI manager are correctly integrated and operating.
ASPI manager Version 4.01 or newer is required. Check the WNASPI32.DLL file version with explorer.
Please refer to "Scanner Utility for Microsoft
R
Windows
R
User's Guide" for details.
3. If an older version is installed, uninstall it before doing the installation.
Installation
1. Turn on the power by pushing the power switch on the scanner's control panel.
The green LED on the control panel lights. The Function No. displayl shows to the order "8","P","0","1". When Function No. display reaches "1" the
scanner is ready.
2. Turn on your personal computer and log on WindowsR.
When using Windows NT R 4.0, log on as an administrator.
3. Insert the Scanner driver CD-ROM, then use explorer to double click on D:\Driver1\ASPI\install.exe (when your CD-ROM is the D drive).
When automatic start has been set, the setup disk start screen is displayed. Installation can be started from this screen also.
4. Follow the instruction on the screen.
5. When installation is finished, confirm that the following group ("Scanner Utility for Microsoft Windows" group) has been created.
Continue by installing Image Capturing Software Utilities "ScandAll 21" for Microsoft RWindows R.
Caution
When using Windows NT R4.0, WindowsR2000 or WindowsRXP, log
on as an administrator .
1. Insert the Scanner driver CD-ROM, then use explorer to double click
on ScandAll 21.exe in the ScandAll folder in the CD-ROM drive.
2. Select the language you use
during installation in [Choose
Setup Language] then click [OK].
This screen might not be
displayed.
3. Click [Next] in the welcome screen.
4. Carefully read the License
Agreement then click [Yes],
if you agree.
5. Confirm the name of the
destination folder then click
[Next].
6. Click [Finish].
The screen images may be changed due to improvements without notice.
If the displayed screen images are slightly different from the screen images in "fi-4220C Quick Installation Guide" follow the actual screen display for installation. Please also refer to the software operation
manual and do the installation according to the actual screens.
Caution
In case of Windows
R
98, Windows
R
Me, Windows
R
2000,
and Windows
R
XP, when documents are set on the scanner,
an application may start automatically or the window for
selecting application may be displayed. If you want to change
these setting, refer to "6.3 Event tab" of "
Scanner Utility for
MicrosoftRWindowsRUser's Guide
."
6. For Windows
R
XP, the next
screen is displayed, click
[Continue Anyway] and
complete the installation.
For Windows
R
2000, the "Digital Signature Not Found" dialog is
displayed, click [Yes].
For other operating systems click [Next].
For Windows
R
98 there is a request to insert a disc.
When this happens, insert the Windows
R
98 CD-ROM.
7. Click [Finish] .
8. Restart the system.
After restarting the system install the TWAIN data source.
Caution
Hint
Installing TWAIN data source
When using Windows
R
2000 or Windows
R
XP log on as an
administrator.
1. Insert the Scanner Driver CD-ROM, then use the explorer to double
click on D:\Driver2\Setup\install.exe (when your CD-ROM is the D
drive).
When automatic start has been set, the setup disk start screen is
displayed.Installation can be started from this screen also.
2. Follow the instruction on the screen to complete the installation. Make
the best selection that suits your needs.
• Select the language you will use during installation.
• Check the installation directory. If you need to change the installation
destination, click the [Browse...] button then specify the destination.
• Check the names of components that need to be installed in [Select
Components]. Explanation of the component is displayed underneath it.
3. When installation is finished, confirm that the following folder has been
created. The icons displayed differ depending on the setting in [Select
Component] during installation.
Continue by installing Image Capturing Software Utilities "ScandAll 21"
for Microsoft RWindows R.
Scanning documents
Continued from previous page