Fujitsu ScanSnap iX1500 Configuration guide

iX1500
Consumable Replacement and Cleaning Instructions
CG00002-299901 Revision A

iX1500 Daily Care and Consumable Replacement Guide
This section describes how to clean the scanner.
Cleaning Materials
ATTENTION
In order to use the cleaning materials safely and correctly, read the precautions on each product thoroughly.
Do not use aerosol spray or spray that contains alcohol. Paper dust blown up by strong air from the spray
may enter inside the scanner which may cause the scanner to fail or malfunction.
Also note that sparks generated by static electricity may cause a fire.
The inside of the ADF becomes very hot when the scanner is being used. Before you start cleaning the inside
of the ADF, make sure to turn off the power, unplug the power cable and wait for at least 15 minutes for the
inside of the ADF to cool down.

For more Information about the cleaning materials, contact the distributor/dealer where you purchased this product.
Or, make an Inquiry by referring to the contact Information at the Contact for Inquiries section In Safety Precautions
bundled with this product.
Cleaning the Inside of the Scanner
Clean the inside of the ScanSnap regularly.
Scanning repeatedly accumulates dust and paper dust inside the ScanSnap, and this may result in an error during a scan.
As a guideline, the inside of the ScanSnap should be cleaned every 1,000 sheets scanned.
Note that this guideline varies depending on the types of documents you scan. For instance, it may be necessary to clean
the scanner more frequently when you scan documents on which the toner is not sufficiently fused.
Notice
-The bottom part of the ScanSnap may become hot when the ScanSnap is being used but this does not affect
ScanSnap operation or cause any physical harm. Be careful not to drop the ScanSnap when carrying it.
-Do not use water or mild detergent to clean the inside of the ScanSnap.
-It may take a long time for Cleaner F1 to dry if an excessive amount is used. Moisten the cloth with a moderate
quantity.
Wipe off the cleaner completely to leave no residue on the cleaned parts.
Cleaning Procedure
(1) Unplug the power cable from the ScanSnap.
(2) Remove any documents from the ADF paper chuter (cover).
(3) Remove the Receipt Guide from the scanner when it is attached.
To remove the Receipt Guide, hold it with one hand and lift it up towards you.

(4) Pull the ADF release tab to open the ADF top section.
(5) Clean the following parts with a cloth moistened with Cleaner F1, or a cleaning wipe.
1. Brake roller (x2)
Remove the brake rollers from the scanner to clean.
Gently wipe the dirt and dust off from along the slots on the surface of the brake rollers. Be careful not to
damage the surface of the rollers.

2. Glass (x2)
Gently wipe the dirt and dust off the surface of the glass sections. Make sure that it is cleaned properly
because dirty glass can cause vertical lines to appear in the scanned image.
3. Ultrasonic sensor (x2)
Gently wipe the dirt and dust off the surface of the ultrasonic sensors.
If you have trouble wiping the ultrasonic sensors with the cloth, use a cotton swab.
4. Pick roller (x1)
Remove the pick roller from the scanner to clean.
Gently wipe off the dirt and dust along the grooves on the roller surface. Residue on the roller
may affect the feeding performance. Be careful not to damage the surface of the roller.
5. Plastic idler roller (x2)
Gently wipe the dirt and dust off the rollers as you rotate them manually. Be careful not to damage the
surface of the rollers. Make sure that they are cleaned properly because residue on the rollers will affect the
feeding performance.
6. Rubber idler roller (x2)
Gently wipe the dirt and dust off the rollers as you rotate them manually. Be careful not to damage the
surface of the rollers. Make sure that they are cleaned properly because residue on the rollers will affect the
feeding performance.
(6) Connect the power cable of the ScanSnap to the AC outlet.
Reference
Connect the power cable only when cleaning the Feed-Roller and the Exit-Roller.
(7) Tap in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.
(8) Tap to display the [Maintenance] screen.
(9) Tap [Roller cleaning] to display the [Roller cleaning] window.
(10) Holding down the [Run] button to rotate the Feed-Roller and the Exit-Roller.
Reference
Release the [Run] button to stop the Feed-Roller and the Exit-Roller.
(11) Clean the following parts with a cloth moistened with Cleaner F1, or a cleaning wipe.

7. Feed-Roller (x2)
8. Exit-Roller (x2)
Gently wipe the dirt and dust off while taking care not to damage the surface of the rollers. Make sure that
they are cleaned properly because residue on the rollers will affect the feeding performance.
(12) Close the ADF top section.

Cleaning the Outside of the Scanner
Scanner
The scanner including the ADF paper chute (feeder) and the stacker should be cleaned with either a piece of dry
cloth, a cloth moistened with Cleaner F1/mild detergent, or a sheet of Cleaning Wipe.
Touch screen
To avoid the surface of the touch screen becoming dirty, clean it regularly by gently wiping dirt and dust off with
a soft, dry cloth.
Clean the touch screen with care. Do not rub or tap the surface with hard objects as doing so may damage the
surface.
ATTENTION
To avoid deformation and discoloration, never use paint thinner or any other organic solvents.
Be careful not to let any moisture or water inside the scanner during cleaning.
It may take a long time to dry if an excessive amount of Cleaner F1/mild detergent is used. Use only a small
amount. Wipe off the cleaner completely to leave no residue on the cleaned parts.
ATTENTION
Do not wipe the touch screen with a damp cloth.
Dust on the surface may become stuck between the touch screen and the scanner, causing the touch screen to
malfunction.

Replacing the Consumables
This section explains how to replace the consumables for the scanner.
Consumables and Replacement Cycles
*1: The suggested replacement cycles are guidelines for using A4 (80 g/㎡[20 lb.]) wood-free paper, as these
cycles vary depending on the type of documents scanned.
Consumables need to be replaced periodically. It is recommended that you keep a stock of new consumables and
replace them before it reaches the end of the consumable life. Also, the scanner records the number of sheets scanned
for each consumable (brake roller and pick roller), which allows you to determine when to replace the consumables.
The inside of the ADF becomes very hot when the scanner is being used.
Before you replace the consumables, make sure to turn off the power, unplug the power cable and wait for at least
15 minutes for the inside of the ADF to cool down.

Before replacing the consumables, check the status of each consumable in the following procedure.
(1) Tap in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.
(2) Tap to display the [Maintenance] screen.
(3) Tap [Check consumable status] to display the [Check consumable status] window.
(4) Check the value for [Current Count / Replacement Cycle].
Note that the suggested replacement cycles are guidelines for using A4 (80 g/m2[20 lb.]) wood-free or wood-containing
paper, as these cycles vary depending on the type of documents scanned and how often the scanner is used and
cleaned.
For information on purchasing the consumables, contact the distributor/dealer where you purchased this product. Or,
make an inquiry by referring to the contact information at the Contact for Inquiries section in Safety Precautions
bundled with this product.
Replacing the Brake Roller
Replace the brake roller in following procedure.
(1) Open the ADF top section.
(2) By holding the both ends of the Guide-R-ASSY (brake roller cover), open it in the direction of the arrow.
HINT
Only use the specified consumables.

(3) Lift the BR-Roller-ASSY on the right side, remove the right-side shaft (①), and pull out the left-side shaft from the slot
(②).
(4) Remove the BR-Roller-ASSY from the BR-Shaft-ASSY.
Installation
(1) Insert the protrusion on the BR-Shaft-ASSY into the groove of the BR-Roller-ASSY.