Fujitsu fi-4530C User manual

for Fujitsu Scanners
Cleaning and Consumable Replacement Instructions
IManualnstruction
Versitec is a division of Cranel, Inc.
fi-4530C & fi-5530C

WARNING !!
TURN OFF SCANNER, DISCONNECT FROM POWER
AND
ALLOW TO COOL FOR AT LEAST 15 MINUTES BEFORE
SERVICING
Limitation of Liability
Before using this product, please read this manual carefully. If this
product is used incorrectly, unforeseen injury may occur.
Although best efforts have been made to ensure all information in this manual is correct,
Cranel Inc. assumes no liability to any party for any damage caused by errors or
omissions or by statements of any kind in this manual or future updates. Cranel Inc.
further assumes neither liability arising from the use of this product nor any liability for
incidental or consequential damages arising from the use of this manual. Cranel Inc.
disclaims all warranties regarding the information contained herein, whether expressed,
implied or statutory.
Kit Contents
Cleaning the Automatic Document Feeder
Location of Parts to be Cleaned
When to Clean
How to Clean
Using the Cleaning Paper
Replacing Consumables
Pad Assembly
Pick Roller
Resetting Consumable Scan Counters
For inquiries during any of these procedures, contact:
Versitec Customer Support Center
1-800-224-3475

Kit Contents
Wipes Cleaning Sheets
Foam Swabs V1 Cleaner
Pad Assembly Pick Roller

Cleaning the Automatic Document Feeder
Opening the ADF
Location of Parts to be Cleaned

Recommended Cleaning Interval
During normal use, the ADF is to be thoroughly cleaned
every 5,000 scans
* Scanning certain documents may require more frequent cleaning *
Some examples are:
Carbonless paper Handwritten documents
Paper with special coatings Glossy paper
Clean in direction of arrows using either
cotton swaps or wipes moistened with V1 cleaner
Pick Arm Rollers Pad Assembly
Glass
Glass can become hot during use
Allow to cool before cleaning
Rollers
Turn by hand to access entire roller
Ultrasonic
Sensors

Using the Cleaning Paper
Cleaning paper is designed to remove loose dust and ink only.
Perform these steps between the manual cleanings described in
the previous section
With the scanner off,
open the ADF
Apply V1 Cleaner to both sides
of cleaning paper and place in
the scanner (the leading edge
should touch the top of the
black plastic pinch rollers)
Close the ADF and
power on the scanner
Turn off the scanner and
repeat process using opposite
side of cleaning paper

Replacing Consumables
Pad Assembly
(Recommended every 100,000 sheets)
Slide the old pad
to the left to remove
Install new pad by inserting
posts into holes in the adf
Slide pad to the right
to lock in place

Pick Roller
(Recommended every 200,000 sheets)
Remove the sheet guide by depressing the tabs and pulling out
Rotate bushing and lift out shaft assembly
Lift tab and remove roller Place new pick roller onto shaft so that screw slides into slot
Insert end of pick shaft into bushing
When installing sheet guide,
make sure tabs go into slots

Resetting Pick Roller and Pad Assembly Counters
After changing consumables, you need to reset the scan counters
Click Start.
Go to Settings and
open the Control Panel
Once in the Control Panel window,
open Scanners and Cameras
Right Click on the scanner
and select properties
Click the Device Set tab
Click the clear buttons
to reset the pad and
pick roller counts
Click OK to finish
and write to EPROM

For inquiries on consumables, call Versitec at: 800.727.2635
Corporate Headquarters
8999 Gemini Parkway
Columbus, OH 43240
Fax: [phone]
Repair Center
908 Boston Turnpike Road
Shrewsbury, MA 01545
Fax: [phone]
Western Region Office
8001 Irvine Center Drive, 4th Floor
Suites 411, 412, 413
Irvine, CA 92618
www.versitec.com