Fujitsu PRIMERGY TX1310 M1 User manual

Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY TX1310 M1
Upgrade and Maintenance Manual
Edition May 2014

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]su.com.
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright © 2014 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

TX1310 M1 Upgrade and Maintenance Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.

Upgrade and Maintenance Manual TX1310 M1
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market: About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://jp.fujitsu.com/platform/server/primergy/harddisk/

TX1310 M1 Upgrade and Maintenance Manual
Version history
Version history
Issue number Reason for update
1.0 / 20.5.2014 Initial release

Upgrade and Maintenance Manual TX1310 M1
V
ersion history

TX1310 M1 Upgrade and Maintenance Manual
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 Notational conventions . . . . . . . . . . . . . . . . . . . . 17
2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1 Classification of procedures . . . . . . . . . . . . . . . . . 20
2.1.1 Customer Replaceable Units (CRU) . . . . . . . . . . . . . . . 20
2.1.2 Upgrade and Repair Units (URU) . . . . . . . . . . . . . . . . 21
2.1.3 Field Replaceable Units (FRU) . . . . . . . . . . . . . . . . . 22
2.2 Average task duration . . . . . . . . . . . . . . . . . . . . . 23
2.3 Tools you need at hand . . . . . . . . . . . . . . . . . . . . 24
2.4 Documents you need at hand . . . . . . . . . . . . . . . . . 25
3 Important information . . . . . . . . . . . . . . . . . . . . . 27
3.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 27
3.2 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.3 FCC Class A Compliance Statement . . . . . . . . . . . . . 34
3.4 Environmental protection . . . . . . . . . . . . . . . . . . . 35
4 Basic hardware procedures . . . . . . . . . . . . . . . . . . 39
4.1 Using diagnostics information . . . . . . . . . . . . . . . . 39
4.1.1 Locating the defective component . . . . . . . . . . . . . . . . 39
4.2 Shutting down the server . . . . . . . . . . . . . . . . . . . 40
4.3 Disconnecting the server from the mains . . . . . . . . . . 41
4.4 Getting access to the component . . . . . . . . . . . . . . . 42
4.4.1 Removing the side cover . . . . . . . . . . . . . . . . . . . . 42
4.4.2 Removing accessible drives . . . . . . . . . . . . . . . . . . . 43
4.4.2.1 Disconnecting the optical disk drive (ODD) . . . . . . . . . 43
4.4.2.2 Disconnecting the backup drive . . . . . . . . . . . . . . . 44

Upgrade and Maintenance Manual TX1310 M1
Contents
4.4.3 Removing the front cover . . . . . . . . . . . . . . . . . . . . . 46
4.5 Reassembling . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.5.1 Installing the front cover . . . . . . . . . . . . . . . . . . . . . 48
4.5.2 Installing accessible drives . . . . . . . . . . . . . . . . . . . . 49
4.5.2.1 Installing the optical disk drive (ODD) . . . . . . . . . . . . . 49
4.5.2.2 Installing the backup drive . . . . . . . . . . . . . . . . . . . 51
4.5.3 Installing the side cover . . . . . . . . . . . . . . . . . . . . . . 53
4.6 Connecting the server to the mains . . . . . . . . . . . . . . 54
4.7 Switching on the server . . . . . . . . . . . . . . . . . . . . . 55
4.8 Handling the HDD cage with system fan 1 . . . . . . . . . . . 56
4.8.1 Removing the HDD cage . . . . . . . . . . . . . . . . . . . . . 56
4.8.2 Installing the HDD cage . . . . . . . . . . . . . . . . . . . . . . 59
5 Basic software procedures . . . . . . . . . . . . . . . . . . . 63
5.1 Starting the maintenance task . . . . . . . . . . . . . . . . . 63
5.1.1 Disabling BitLocker functionality . . . . . . . . . . . . . . . . . 63
5.1.2 Removing backup and optical disk media . . . . . . . . . . . . 64
5.1.3 Verifying and configuring the backup software solution . . . . . . 65
5.1.4 Note on server maintenance in a Multipath I/O environment . . . 65
5.2 Completing the maintenance task . . . . . . . . . . . . . . . 68
5.2.1 Updating or recovering the system board BIOS . . . . . . . . . 68
5.2.1.1 Updating or recovering the system board BIOS . . . . . . . . 68
5.2.2 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . . 68
5.2.3 Verifying and configuring the backup software solution . . . . . . 69
5.2.4 Enabling replaced components in the system BIOS . . . . . . . 70
5.2.5 Verifying the system time settings . . . . . . . . . . . . . . . . 72
5.2.6 Viewing the System Event Log (SEL) . . . . . . . . . . . . . . . 72
5.2.6.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . . 72
5.2.7 Updating the NIC configuration file in a Linux environment . . . . 73
5.2.8 Enabling BitLocker functionality . . . . . . . . . . . . . . . . . . 74
5.2.9 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 75
5.2.10 Looking up changed MAC / WWN addresses . . . . . . . . . . 76
5.2.10.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . . 76
5.2.11 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 76
5.2.12 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . . 77
5.2.12.1 After replacing / upgrading LAN controllers . . . . . . . . . . 77
5.2.12.2 After replacing the system board . . . . . . . . . . . . . . . 78

TX1310 M1 Upgrade and Maintenance Manual
Contents
6 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.1 Replacing the power supply unit . . . . . . . . . . . . . . . 80
6.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 80
6.1.2 Removing the defective power supply unit . . . . . . . . . . . 80
6.1.3 Installing the new power supply unit . . . . . . . . . . . . . . . 82
6.1.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 84
7 Hard disk drives . . . . . . . . . . . . . . . . . . . . . . . . 85
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 86
7.1.1 General equipping rules . . . . . . . . . . . . . . . . . . . . . 86
7.1.2 Mounting order . . . . . . . . . . . . . . . . . . . . . . . . . . 86
7.2 Installing 3.5-inch HDDs . . . . . . . . . . . . . . . . . . . . 87
7.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 87
7.2.2 Removing the Easyclick rail out of the bay . . . . . . . . . . . 87
7.2.3 Installing a 3.5-inch HDD . . . . . . . . . . . . . . . . . . . . 88
7.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 91
7.3 Removing 3.5-inch HDDs . . . . . . . . . . . . . . . . . . . 92
7.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 92
7.3.2 Removing a 3.5-inch HDD . . . . . . . . . . . . . . . . . . . . 93
7.3.3 Inserting the Easyclick rails in the bay . . . . . . . . . . . . . . 96
7.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 96
7.4 Replacing a 3.5-inch HDD . . . . . . . . . . . . . . . . . . . 97
7.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 97
7.4.2 Removing the defective 3.5-inch HDD . . . . . . . . . . . . . . 97
7.4.3 Installing the new 3.5-inch HDD . . . . . . . . . . . . . . . . . 98
7.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 98
8 System fans . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 100
8.2 Replacing the system fan 2 . . . . . . . . . . . . . . . . . . 102
8.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 102
8.2.2 Removing the defective system fan 2 . . . . . . . . . . . . . . 102
8.2.3 Installing the new system fan 2 . . . . . . . . . . . . . . . . . 105
8.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 108
8.3 Replacing the system fan 1 . . . . . . . . . . . . . . . . . . 109

Upgrade and Maintenance Manual TX1310 M1
Contents
8.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 109
8.3.2 Removing the defective system fan 1 . . . . . . . . . . . . . . 109
8.3.3 Installing the new system fan 1 . . . . . . . . . . . . . . . . . 112
8.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 114
9 Expansion cards and backup units . . . . . . . . . . . . . 115
9.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 116
9.1.1 Equipping the PCIe slots . . . . . . . . . . . . . . . . . . . . 117
9.2 Handling slot brackets . . . . . . . . . . . . . . . . . . . . 118
9.2.1 Installing a slot bracket . . . . . . . . . . . . . . . . . . . . . 118
9.2.2 Removing a slot bracket . . . . . . . . . . . . . . . . . . . . 122
9.3 Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . 123
9.3.1 Installing expansion cards . . . . . . . . . . . . . . . . . . . 123
9.3.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 123
9.3.1.2 Removing the PCI slot bracket . . . . . . . . . . . . . . . 123
9.3.1.3 Installing an expansion card . . . . . . . . . . . . . . . . . 125
9.3.1.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 126
9.3.2 Removing expansion cards . . . . . . . . . . . . . . . . . . . 127
9.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 127
9.3.2.2 Removing an expansion card . . . . . . . . . . . . . . . . 127
9.3.2.3 Installing a PCI slot bracket . . . . . . . . . . . . . . . . . 128
9.3.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 129
9.3.3 Replacing expansion cards . . . . . . . . . . . . . . . . . . . 130
9.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 130
9.3.3.2 Removing an expansion card . . . . . . . . . . . . . . . . 130
9.3.3.3 Installing an expansion card . . . . . . . . . . . . . . . . . 130
9.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 131
10 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . 133
10.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 134
10.1.1 Memory sequence . . . . . . . . . . . . . . . . . . . . . . . 134
10.1.2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . 135
10.2 Installing memory modules . . . . . . . . . . . . . . . . . . 136
10.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 136
10.2.2 Installing a memory module . . . . . . . . . . . . . . . . . . . 136
10.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 137
10.3 Removing memory modules . . . . . . . . . . . . . . . . . 138

TX1310 M1 Upgrade and Maintenance Manual
Contents
10.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 138
10.3.2 Removing a memory module . . . . . . . . . . . . . . . . . . 138
10.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 139
10.4 Replacing memory modules . . . . . . . . . . . . . . . . . . 139
10.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 139
10.4.2 Removing the defective memory module . . . . . . . . . . . . 139
10.4.3 Installing the new memory module . . . . . . . . . . . . . . . 139
10.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 140
11 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
11.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 142
11.2 Replacing the processor . . . . . . . . . . . . . . . . . . . . 142
11.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 142
11.2.2 Removing the heat sink . . . . . . . . . . . . . . . . . . . . . 143
11.2.3 Removing processor . . . . . . . . . . . . . . . . . . . . . . . 145
11.2.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 145
11.2.3.2 Removing a processor . . . . . . . . . . . . . . . . . . . . 145
11.2.3.3 Installing the protective cover . . . . . . . . . . . . . . . . 148
11.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 149
11.2.5 Installing a processor . . . . . . . . . . . . . . . . . . . . . . 150
11.2.5.1 Removing the protective cover . . . . . . . . . . . . . . . . 150
11.2.5.2 Installing the new processor . . . . . . . . . . . . . . . . . 152
11.2.6 Applying thermal paste . . . . . . . . . . . . . . . . . . . . . 154
11.2.7 Installing the heat sink . . . . . . . . . . . . . . . . . . . . . . 156
11.2.8 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 157
11.3 Replacing the heat sink . . . . . . . . . . . . . . . . . . . . 158
11.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 158
11.3.2 Removing the heat sink . . . . . . . . . . . . . . . . . . . . . 158
11.3.3 Installing the new heat sink . . . . . . . . . . . . . . . . . . . 158
11.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 158
12 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 159
12.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 160
12.2 Installing accessible drives . . . . . . . . . . . . . . . . . . 161
12.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 161
12.2.2 Removing the dummy cover of bay 2 . . . . . . . . . . . . . . 162
12.2.3 Installing an optical disk drive (ODD) . . . . . . . . . . . . . . 164

Upgrade and Maintenance Manual TX1310 M1
Contents
12.2.3.1 Preparing the optical disk drive . . . . . . . . . . . . . . . 164
12.2.3.2 Installing the optical disk drive . . . . . . . . . . . . . . . 166
12.2.4 Installing a slimline optical disk drive (ODD) . . . . . . . . . . 167
12.2.4.1 Mounting the slimline drive in the slide-in unit . . . . . . . . 167
12.2.4.2 Preparing the slide-in unit . . . . . . . . . . . . . . . . . . 168
12.2.4.3 Installing the slide-in unit . . . . . . . . . . . . . . . . . . 169
12.2.5 Installing a backup drive . . . . . . . . . . . . . . . . . . . . 170
12.2.5.1 Preparing the backup drive . . . . . . . . . . . . . . . . . 171
12.2.5.2 Installing the backup drive . . . . . . . . . . . . . . . . . . 172
12.2.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 172
12.3 Removing accessible drives . . . . . . . . . . . . . . . . . 173
12.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 173
12.3.2 Removing an optical disk drive (ODD) . . . . . . . . . . . . . 173
12.3.3 Removing a slimline optical disk drive (ODD) . . . . . . . . . 174
12.3.4 Removing a backup drive . . . . . . . . . . . . . . . . . . . . 175
12.3.5 Installing the dummy drive . . . . . . . . . . . . . . . . . . . 176
12.3.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 177
12.4 Replacing accessible drives . . . . . . . . . . . . . . . . . 178
12.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 178
12.4.2 Replacing an optical disk drive (ODD) . . . . . . . . . . . . . 178
12.4.3 Replacing a slimline optical disk drive (ODD) . . . . . . . . . . 179
12.4.4 Replacing a backup drive . . . . . . . . . . . . . . . . . . . . 181
12.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 182
13 Front panel and front USB . . . . . . . . . . . . . . . . . . 183
13.1 Replacing the front panel cable . . . . . . . . . . . . . . . 183
13.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 183
13.1.2 Removing the On/Off button and the HDD activity LED . . . . 184
13.1.3 Removing the front panel cable . . . . . . . . . . . . . . . . . 185
13.1.4 Installing the front panel cable . . . . . . . . . . . . . . . . . 185
13.1.5 Installing the On/Off button and the HDD activity LED . . . . . 186
13.1.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 186
13.2 Replacing the front USB module . . . . . . . . . . . . . . . 187
13.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 187
13.2.2 Removing the defective front USB module . . . . . . . . . . . 188
13.2.3 Installing the new front USB module . . . . . . . . . . . . . . 190
13.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 192

TX1310 M1 Upgrade and Maintenance Manual
Contents
14 System board and components . . . . . . . . . . . . . . . . 193
14.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 193
14.2 Replacing the CMOS battery . . . . . . . . . . . . . . . . . 194
14.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 194
14.2.2 Replacing the defective CMOS battery . . . . . . . . . . . . . 195
14.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 195
14.3 Trusted Platform Module (TPM) . . . . . . . . . . . . . . . . 196
14.3.1 Installing the TPM . . . . . . . . . . . . . . . . . . . . . . . . 196
14.3.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 196
14.3.1.2 Installing the TPM . . . . . . . . . . . . . . . . . . . . . . 197
14.3.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 199
14.3.2 Removing the TPM . . . . . . . . . . . . . . . . . . . . . . . 200
14.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 200
14.3.2.2 Removing the TPM . . . . . . . . . . . . . . . . . . . . . . 202
14.3.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 203
14.3.3 Replacing the TPM . . . . . . . . . . . . . . . . . . . . . . . 204
14.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 204
14.3.3.2 Removing the defective TPM . . . . . . . . . . . . . . . . 205
14.3.3.3 Installing the new TPM . . . . . . . . . . . . . . . . . . . . 205
14.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 205
14.4 Replacing the system board . . . . . . . . . . . . . . . . . . 206
14.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 207
14.4.2 Removing the defective system board . . . . . . . . . . . . . . 208
14.4.3 Installing the new system board . . . . . . . . . . . . . . . . . 212
14.4.3.1 Mounting the system board . . . . . . . . . . . . . . . . . 212
14.4.3.2 Swapping the processor . . . . . . . . . . . . . . . . . . . 215
14.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 215
15 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
15.1 Overview cables . . . . . . . . . . . . . . . . . . . . . . . . 217
15.2 Cabling plans . . . . . . . . . . . . . . . . . . . . . . . . . . 218
15.3 Storing not used SATA cables . . . . . . . . . . . . . . . . . 219

Upgrade and Maintenance Manual TX1310 M1
Contents
16 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
16.1 Mechanical overview . . . . . . . . . . . . . . . . . . . . . 221
16.1.1 Server front . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
16.1.2 Server rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
16.1.3 Server interior . . . . . . . . . . . . . . . . . . . . . . . . . . 223
16.2 Connectors and indicators . . . . . . . . . . . . . . . . . . 225
16.2.1 Connectors on the system board . . . . . . . . . . . . . . . . 225
16.2.1.1 Onboard connectors . . . . . . . . . . . . . . . . . . . . . 225
16.2.1.2 I/O panel connectors . . . . . . . . . . . . . . . . . . . . 227
16.2.1.3 I/O panel indicators . . . . . . . . . . . . . . . . . . . . . 228
16.2.2 Connectors and indicators on the front panel . . . . . . . . . . 229
16.3 Onboard settings . . . . . . . . . . . . . . . . . . . . . . . 230
16.4 Minimum startup configuration . . . . . . . . . . . . . . . . 231

TX1310 M1 Upgrade and Maintenance Manual 15
1 Introduction
This Upgrade and Maintenance Manual provides instructions for the following
procedures:
● Upgrading the server configuration by adding optional hardware
components
● Upgrading the server configuration by replacing existing hardware
components with superior ones.
● Replacing defective hardware components
This manual focuses on on-site maintenance tasks. It is recommended to
prepare each service assignment following remote diagnostics procedures, as
described in the "ServerView Suite Local Service Concept (LSC)" manual (see
section "Documents you need at hand" on page 25.
VCAUTION!
The document at hand comprises procedures of a wide range of
complexity. Check the profile of qualification for technicians before
assigning tasks. Before you start, carefully read "Classification of
procedures" on page 20.

16 Upgrade and Maintenance Manual TX1310 M1
Introduction
Different versions for TX1310 M1
The PRIMERGY TX1310 M1 is available in different versions. Your base unit
may not have all functions described in this manual.
The following table
provides an overview of the different features:
System board D3219-Axx D3219-Bxx
Main Memory 4 slots for 1600 MHz
memory modules DIMM
1A, 1B, 2A, 2B
2 slots for 1600 MHz memory
modules DIMM 1A, 1B
PCI slots Slot 1: PCIe x1 slot Gen 2
(mechanically x4)
Slot 2: PCIe x4 slot Gen 2
(mechanically x8)
Slot 3: PCIe x8 slot Gen 3
(mechanically x8,
notched)
Slot 4: PCIe x8 slot Gen 3
(mechanically x8,
notched)
Slot 1: not assembled
Slot 2: not assembled
Slot 1: PCIe x8 slot Gen 3
(mechanically x8, notched)
Slot 2: PCIe x8 slot Gen 3
(mechanically x8, notched)

TX1310 M1 Upgrade and Maintenance Manual 17
Introduction
1.1 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items
fixed font indicates system output
semi-bold fixed
font
indicates text to be entered by the user
"Quotation marks" indicate names of chapters and terms that are being
emphasized
Êdescribes activities that must be performed in the order
shown
[Abc] indicates keys on the keyboard
VCAUTION! Pay particular attention to texts marked with this symbol!
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips
indicates the procedure category in terms of complexity
and qualification requirements, see "Classification of
procedures" on page 20
indicates the average task duration, see "Average task
duration" on page 23

18 Upgrade and Maintenance Manual TX1310 M1
Introduction

TX1310 M1 Upgrade and Maintenance Manual 19
2 Before you start
Before you start any upgrade or maintenance task, please proceed as follows:
ÊCarefully read the safety instructions in chapter "Important information" on
page 27.
ÊMake sure that all necessary manuals are available. Refer to the
documentation overview in section "Documents you need at hand" on
page 25. Print the PDF files if required.
ÊMake yourself familiar with the procedure categories introduced in section
"Classification of procedures" on page 20.
ÊEnsure that all required tools are available according to section "Tools you
need at hand" on page 24.
Installing optional components
The operating manual of your server gives an introduction to server features
and provides an overview of available hardware options.
Use the Fujitsu ServerView Suite management software to prepare hardware
expansions. ServerView Suite documentation is available online at
http://manuals.ts.fujitsu.com (http://jp.fujitsu.com/platform/server/primergy/manual/
for the Japanese market). Please refer to the following ServerView Suite topics:
– Operation
– Virtualization
– Maintenance
– Out-Of-Band Management
IFor the latest information on hardware options, refer to your server’s
hardware configurator available online at the following address:
for the EMEA market:
http://ts.fujitsu.com/products/standard_servers/index.htm
for the Japanese market:
http://jp.fujitsu.com/platform/server/primergy/system/
Please contact your local Fujitsu customer service partner for details on how to
order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog
to identify the required spare part and obtain technical data and order
information. Illustrated Spares catalogs are available online at
http://manuals.ts.fujitsu.com/illustrated_spares (EMEA market only).

20 Upgrade and Maintenance Manual TX1310 M1
Before you start
Replacing a defective component
It is recommended to prepare local maintenance tasks using remote diagnostics
procedures, as described in the "ServerView Suite Local Service Concept
(LSC)" manual.
2.1 Classification of procedures
The complexity of maintenance procedures varies significantly. Procedures
have been assigned to one of three unit categories, indicating the level of
difficulty and required qualification.
At the beginning of each procedure, the involved unit type is indicated by one of
the symbols introduced in this section.
IPlease ask your local Fujitsu service center for more detailed
information.
2.1.1 Customer Replaceable Units (CRU)
Customer Replaceable Units are intended for customer self service.
IComponents that the customer is entitled to replace may differ according
to the service form in his country.
Peripherals that are handled as Customer Replaceable Units
– Keyboard
– Mouse
Customer Replaceable Units (CRU)