Fujitsu PRIMERGY Econel 200 S2 User manual

PRIMERGY
PRIMERGY Econel 200 S2
Server
Options Guide
Susanne Däschlein
Fujitsu Siemens Computers GmbH München
81730 Munich
e-mail: email: [email protected]
Tel.: [phone]
Fax: (++49) 700 / 372 00000
Econel200 S2
Sprachen: En
Edition January 2007

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademar s
Copyright © 2007 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

Econel200 S2 Options Guide
Contents
1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Overview of the documentation . . . . . . . . . . . . . . . . . 5
1.2 Expansions and conversions . . . . . . . . . . . . . . . . . . 7
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . . 8
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . 17
4.2 Removing the processor fan 2 . . . . . . . . . . . . . . . . 18
4.3 Removing the system fan . . . . . . . . . . . . . . . . . . . 19
4.4 Removing the memory air duct . . . . . . . . . . . . . . . . 21
4.5 Removing the processor fan 1 . . . . . . . . . . . . . . . . 22
5 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1 Installing a second processor . . . . . . . . . . . . . . . . 25
6 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1 Slot population rules . . . . . . . . . . . . . . . . . . . . . 29
6.2 Installing/removing main memory . . . . . . . . . . . . . . 30
7 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 33
7.1 Installing an accessible drive . . . . . . . . . . . . . . . . . 33
7.2 Installing the 5-inch multibay . . . . . . . . . . . . . . . . . 35

Options Guide Econel200 S2
Contents
8 Hard disk drives . . . . . . . . . . . . . . . . . . . . . . . . 41
8.1 Installing SATA hard disk drives . . . . . . . . . . . . . . . 41
9 Expansion boards in PCI slots . . . . . . . . . . . . . . . . 45
9.1 Installing an expansion board . . . . . . . . . . . . . . . . . 45
10 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
10.1 Installing the processor fan 1 . . . . . . . . . . . . . . . . . 49
10.2 Installing the memory air duct . . . . . . . . . . . . . . . . 50
10.3 Installing the system fan . . . . . . . . . . . . . . . . . . . 51
10.4 Installing the processor fan 2 . . . . . . . . . . . . . . . . . 52
10.5 Closing the server . . . . . . . . . . . . . . . . . . . . . . . 53
11 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Econel200 S2 Options Guide 5
1Introduction
The PRIMERGY Econel 200 S2 server is an Intel-based server for workgroups
and small networks. The server is suitable for use as a file server and also as
an application, information or Internet server.
1.1 Overview of the documentation
IPRIMERGY manuals are available in PDF format on the ServerBooks
DVD which is supplied in the PRIMERGY ServerView Suite package for
every server system.
These PDF files can also be downloaded free of charge from the
Internet: at http://manuals.fujitsu-siemens.com you will find an overview
page with the online documentation available on the Internet. You can go
to the PRIMERGY Server documentation by clicking on industry standard
servers.
Concept and target groups
This Options Guide shows you how you can expand and upgrade the server.
The activities described in this manual may only be performed by technical
specialists.
Additional documentation about the server
The PRIMERGY Econel 200 S2 documentation comprises the following
additional manuals:
– “Safety notes and other important information” (print version delivered
together with the system, PDF file available on the ServerBooks DVD)
– “Warranty” (print version delivered together with the system, PDF file
available on the ServerBooks DVD)
– “Ergonomics” (PDF file available on the ServerBooks DVD)
– “Returning used devices” (PDF file available on the ServerBooks DVD)
– “PRIMERGY Econel 200 S2 Operating Manual” (PDF file available on the
ServerBooks DVD)
– Technical Manual for the system board D2530 (PDF file available on the
ServerBooks DVD)

6 Options Guide Econel200 S2
Overview of the documentation Introduction
– “BIOS Manual” (PDF file available on the ServerBooks DVD)
– “PRIMERGY ServerView Suite” includes the ServerStart Disc 1 and 2, the
ServerBooks DVD, the Software CD and the update CDs for Windows and
Linux. The PDF version of the manual “PRIMERGY ServerView Suite -
ServerStart” is also available on the ServerBooks DVD.
IIf you need a backup of the ServerBooks DVD, send the details of your
server via email address:
[email protected].
– “LSI SATA Software RAID User’s Guide“ (PDF file available on the
ServerBooks DVD)
Further sources of information:
– Manual on the monitor
– Manual on ServerView Server Management
– Manual on RemoteView Remote Server Maintenance
– Documentation on boards and drives
– Documentation on your operating system
– Information files on your operating system
(see also “Related publications” on page 59).

Econel200 S2 Options Guide 7
Introduction Expansions and conversions
1.2 Expansions and conversions
Second processor
The server can be upgraded to a so-called dual processor system. A dual
processor system needs a multi processor operating system. The second
processor must have the same type and clock rate as the first.
Extension of the main memory
The system board supports up to 8 Gbyte main memory. 4 slots (2 banks with
2 modules) are available for the main memory. Each memory bank can be
populated with 512 Mbyte, 1 Gbyte or 2 Gbyte FBD533/PC2-4200F Fully
Buffered DIMM memory modules. You find further information on the main
memory in the Technical Manual for the system board D2530.
Additional accessible drives
Three free 5.25-inch bays are available for additional accessible drives
(DVD-ROM, CD-RW/DVD, DVD-RW or tape backup drive).
The lowest bay can be equipped with a 5-inch multibay. In this multibay a
1.44 MB floppy disk drive and a slimline drive (CD-RW/DVD, DVD-RW) can be
installed.
Hard disk drives
Up to four SATA hard disk drives can be installed. One SATA hard disk drive is
already installed in the base unit.
Expansion boards in the PCI slots
The system board offers:
– 3 x PCI-X (133/100 MHz) slots
– 1 x PCI 33 MHz slot
– 1 x PCI-Express x16 slot (x8 wired)
– 1 x PCI-Express x8 slot (x4 wired)

8 Options Guide Econel200 S2
Notational conventions Introduction
1.3 Notational conventions
The following notational conventions are used in this manual:
text in italics indicate commands, menu items or software programs.
“quotation marks” indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown
VCAUTION! Pay particular attention to texts marked with this
symbol. Failure to observe this warning may endanger
your life, destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips
Table 1: Notational conventions

Econel200 S2 Options Guide 9
2Procedure
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
service personnel. Any unauthorized opening and improper repairs could
expose the user to risks (electric shock, energy hazards, fire hazards)
and could also damage the equipment. Please note that any unautho-
rized opening of the device will result in the invalidation of the warranty
and exclusion from all liability.
ÊFirst of all please familiarize yourself with the safety instructions in the
chapter “Safety notes” on page 11 et seq. .
ÊEnsure that all required manuals (see “Additional documentation about the
server” on page 5) are available, printing out the PDF files if necessary. You
will definitely need the Operating Manual for the server and the Technical
Manual for the system board.
ÊShut down the server correctly, switch it off, pull out the power plug, and
open the server as described in the chapter “Preparation” on page 17 et
seq. .
ÊExtend or upgrade your server as described in the relevant chapter.
ÊClose the server, connect it to the power outlet, and switch it on as described
in the chapter “Completion” on page 49 et seq. .
ÊStart the operating system and, if necessary, configure it as required (see
Operating Manual).

Econel200 S2 Options Guide 11
3 Safety notes
IThe following safety notes are also provided in the “Safety notes and
other important information” manual.
This device complies with the relevant safety regulations for data processing
equipment.
If you have any questions about where you can set up the device, contact your
sales outlet or our customer service team.
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
service personnel. Any unauthorized openings and improper repairs
could expose the user to risks (electric shock, energy hazards, fire
hazards) and could also damage the equipment. Please note that any
unauthorized openings of the device will result in the invalidation of the
warranty and exclusion from all liability.
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.

12 Options Guide Econel200 S2
Safety notes
Installation and operation
VCAUTION!
●The server automatically sets itself to a voltage in the range of
100 V to 240 V. Make sure that your local voltage is within this range.
●This device has a specially approved power cable and must only be
connected to a grounded insulated socket.
●Ensure that the power socket on the device or the grounded wall
outlet is freely accessible.
●The ON/OFF button does not disconnect the device from the mains
voltage. To disconnect the line voltage completely, remove the power
plug from the grounded insulated socket.
●Always connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the peripheral device
(e.g. storage subsystem) has failed during a power outage.
●Data cables must be adequately shielded.
●To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
Otherwise you run the risk of losing data if, for example, the central
processing unit is still running but the peripheral device (e.g. storage
subsystem) has failed during a power outage.

Econel200 S2 Options Guide 13
Safety notes
VCAUTION!
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risc of electric shock or short circuit).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign matter), switch off the device immediately, remove
the power plug and contact your sales outlet or customer service
team.
●Proper operation of the system (in accordance with
IEC 60950/EN 60950) is only ensured if the casing is completely
assembled and the rear covers for the installation openings have
been put in place (electric shock, cooling, fire protection, interference
suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and relating
to telecommunications terminal equipment. If you install other expan-
sions, you may damage the system or violate the safety regulations
and regulations governing RFI suppression. Information on which
system expansions are suitable can be obtained from the customer
service centre or your sales outlet.
●The components or parts marked with a warning label (e.g. lightning
symbol) may only be opened, removed or exchanged by authorized,
qualified personnel.
●The warranty expires if the device is damaged during the installation
or replacement of system expansions.
●You may only set those resolutions and refresh rates specified in the
“Technical data” section of the monitor description. Otherwise, you
may damage your monitor. If you are in any doubt, contact your sales
outlet or customer service centre.

14 Options Guide Econel200 S2
Safety notes
Batteries
VCAUTION!
●Incorrect replacement of batteries may lead to a risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (see the technical manual for the
system board under “Related publications” on page 59).
●Replace the lithium battery on the system board in accordance with
the instructions in the technical manual for the system board (see
“Related publications” on page 59).
Notes on handling CD and DVD drives
VCAUTION!
●Use only CDs/DVDs in proper condition in the CD/DVD drive of your
server to prevent data loss, damage to the device and injuries.
●Therefore, check each CD/DVD for damage, cracks, breakage etc.
before inserting it in the drive.
Please note that any additional labels applied may change the
mechanical properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain conditions sharp-edged pieces of broken CDs/DVDs
can penetrate the cover of the drive (damage to the device) and be
thrown out of the device (danger of injury, particularly on uncovered
body parts such as the face or neck).
IYou protect the CD/DVD drive and prevent mechanical damage, as well
as premature wearing of the CDs/DVDs, by observing the following
suggestions:
– Only insert the CDs/DVDs in the drive when needed and remove
them after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.

Econel200 S2 Options Guide 15
Safety notes
Note about the laser
The CD/DVD drive is classified for laser class 1 according to IEC 60825-1.
VCAUTION!
The CD/DVD drive contains a laser diode (LED). Sometimes the LED
produces a stronger laser beam than laser class 1. Direct view into the
laser beam is dangerous.
Never remove parts of the CD/DVD drive assembly!
Modules with electrostatic-sensitive components:
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug from the power socket before inserting or removing
components containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Only touch the components at the positions highlighted in green (touch
point).
●Do not touch any exposed pins or conductors on a component.

16 Options Guide Econel200 S2
Safety notes
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).

Econel200 S2 Options Guide 17
4 Preparation
VCAUTION!
Refer to the safety notes in chapter “Safety notes” on page 11 et seq. .
4.1 Opening the server
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the server, press the ON/OFF
button.
ÊRemove the power plug from the grounded insulated socket.
ÊIf required, remove the lock on the side cover.
Figure 2: Removing the side cover
ÊOpen the latch (1).
The opening of the latch pushes back the side cover (2) and disengages the
hooks on the top of the side cover.
ÊRemove the side cover (3).
1
2
3

18 Options Guide Econel200 S2
Removing the processor fan 2 Preparation
4.2 Removing the processor fan 2
For the installation of additional memory modules or installation of a second
processor the processor fan 2 has to be removed.
ÊRemove the side cover as described in section “Opening the server” on
page 17.
Figure 3: Removing the processor fan 2 cable
ÊDisconnect the plug of the processor fan cable from the system board
(connector Fan2 CPU, see circle).

Econel200 S2 Options Guide 19
Preparation Removing the system fan
Figure 4: Removing the processor fan 2
ÊPress together the two locks (see arrows) of the air duct, use the grip at the
right side and remove the air duct with the integrated processor fan 2.
4.3 Removing the system fan
For the installation of PCI controllers or installation of a second processor the
system fan has to be removed.
ÊRemove the side cover as described in section “Opening the server” on
page 17.
ÊRemove the processor fan 2 as described in section “Removing the
processor fan 2” on page 18.
grip

20 Options Guide Econel200 S2
Removing the system fan Preparation
Figure 5: Removing the system fan
ÊPull the locking bar (see arrow) upward and remove the system fan.