Fujitsu PRIMERGY TX150 S4 Technical manual

PRIMERGY TX150 S4
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0System software
IBasic unit
II Processor
III Memory
IV Graphics
VAccessible drives
VI Hard disk drives
VII SCSI Controller
VIII Disk array
IX Communication/Network
XSystem management options
XI Miscellaneous
XII Country specific options
Change report
PRIMERGY Server
December 2005

System configurator and order-information guide
PRIMERGY TX150 S4 Status 25.11.2005
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/ System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section III Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options.
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://www.primergy.com
(internet)
http://extranet.fujitsu-siemens.com/primergy
(extranet)
Prices and availability see price list and PC-/ System-Architect
Subject to change and errors excepted
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 2 of 18

System configurator and order-information guide
PRIMERGY TX150 S4 Status 25.11.2005
Configuration diagram PRIMERGY TX150 S4
System unit ( I )
SIDE VIEW FRONT VIEW
3 x 5.25"
or PS (I) 5.25" x 1.6"
1. PSU 2. PSU
Redundant power supply option 5.25" x 1.6"
Modul 1
Pentium 4
Modul 3
Modul 2
Accessible drives ( V )
Modul 4
Processor ( II )
Memory ( III )
Extension slots
SCSI Controller ( VII )
Disk array ( VIII ) Hard disk drives ( VI )
Communication/Network ( IX )
PCIe x 1
PCIe x 4 (x8 Slot)
PCI short (5V) 32-Bit / 33MHz
PCI short (5V) 32-Bit / 33MHz
PCI-X 66 long (3,3V)
PCI-X 66 long (3,3V)
(Slot for Zero-Channel Controller)
PCI long (5V) 32-Bit / 33MHz
Key:
Included in basic unit
Option
1 PCI-Bus
5.25" x 1.6" CD / DVD drive
Bank 1Bank 2
4.2.1. 7.
Standard Power Supply
SCSI 1"
3.
SCSI 1"
SCSI 1"
5.
SCSI 1"
6.
3.5"x1" Floppy disk (optional)
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 3 of 18

System configurator and order-information guide
Start PRIMERGY TX150 S4
PRIMERGY TX150 S4 Status 25.11.2005
SW Configurator IA32
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
Later use of OEM operating system
VMware-Software software is not allowed,
- VCMS VirtualCenter Management Server apart from few VMware
- GSX Server and GSX Virtual Infrastructure Node add-ons
- P2V Assistant Enterprise Edition
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Microsoft - Software: **) OES/NetWare-Software ***) PRIMECLUSTER *)
- Small Business Server 2003 - NetWare - Clustering
- Windows Server 2003, - Load Balancing
Web Edition (only English)
Standard Edition
Enterprise Edition
- Additional loose Linux - Software: **)
Client-Access-Licenses (CALs) - SUSE Linux Enterprise Server
(not for Web Edition) - SUSE Professional Linux
- Red Hat Enterprise Linux
SCO - Software: **)
- SCO OpenServer
- SCO UnixWare
CITRIX-Software für
Windows: W-MF
- Presentation Server
LoadBalancing
Additional User Licences
Manageability Software: V**) Details eg. version numbers are published
- RemoteView Software in the separate SW-Configurator
- RemoteView Service Board
- RemoteDeploy
- Terminal Server Deploy *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
- vPMS 2005std
http://extranet.fujitsu-siemens.com/primecluster
- Altiris Server Deployment
**) Pay attention to the release and ordering information in PRINCE -> Operating System
Backup-Software /
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
Application-Software: U
- ARCserve
- openSM2 ***) Supply over distribution or procurement from FSC VP BC Software
Various Software Configurators and release lists (OS-Matrix / System Management / Security) can be optain under the following adresses:
for internal users:
http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 4 of 18

System configurator and order-information guide
Start PRIMERGY TX150 S4
PRIMERGY TX150 S4 Status 25.11.2005
SW Configurator EM64T
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
Later use of OEM operating system
software is not allowed,
apart from few VMware
add-ons
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Microsoft - Software: W Linux - Software: L *) **)
only - Windows Server 2003, only
- SuSE Linux Enterprise Server
EM64T x64 Standard Edition EM64T - Red Hat Enterprise Linux
x64 Enterprise Edition
- Additional loose
Client-Access-Lizenzen (CALs)
Details eg. version numbers are published
in the separate SW-Configurator
Manageability Software: V**)
- RemoteView Software
- RemoteView Service Board *) Pay attention to release information on datasheet under
- RemoteView Diagnosis
http://www.primecluster.com
**) Pay attention to release and order information in PRINCE -> Operating System
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
***) Supply over distribution or procurement from FSC VP BC Software
Various Software Configurators and release lists (OS-Matrix / System Management / Security) can be optain under the following adresses:
for internal users:
http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 5 of 18

System configurator and order-information guide
Start PRIMERGY TX150 S4
PRIMERGY TX150 S4 Status 25.11.2005
Section IBasic unit
System unit consisting of:
* Housing including standard power supply (no redundancy)
* Sliding screen with lock (only for floorstand version)
Systemboard with:
* 7 PCI slots:
1x PCIe x 1
1x PCIe x 4 (x8 Slot)
1x PCI-X 66 long (3,3V)
1x PCI-X 66 (3,3V) ZCR Slot
1x long / 2x short 32Bit / 33MHz (5V)
* 4 memory slots for up to 8GB (PC4200) registered DDR II RAM (ECC), max. 2GB modul per slot
* 1 drive bay 3.5" occupied by 1 floppy disk 1.44MB 1" height (optional)
* 3 Einbauplätze 5,25" für bedienbare Laufwerke
* 4 bays 1" for hot plug SCSI HD)
* ATI Range XL Graphic controller 8MB
* Intel Broadcom (5721) 10/100/1000 Mb/s on-board
* 1 x Fast-IDE (ATA) Controller on-board (for 1x 2 devices)
* 1-channel Ultra 320 SCSI Controller LSI 1020A on-board
with HW RAID IME (IME = Integrated Mirroring Enhanced)
Options:
* Hot plug PS or a second redundant hot plug PS version can be configured by ordering the
appropriate upgrade option
* LSI Zero Channel RAID option, simultaneous use of HD and Tape Drive possible
Cables:
1. IDE cable for CD/DVD
2. With SCSI variant wide LVD SCSI cable for connection of the HD backplane and two
accessible drives
PS/2 mouse (only for floorstand version)
ServerStart packet incl. ServerBooks CD, ServerSupport CD and ServerView
External Interfaces:
2x RS-232-C (serial, 9 pins)
1x Centronics (parallel, 25 pins, EPP/ECP compatible)
1x keyboard (PS/2)
1x mouse (PS/2)
1x VGA (15 pins)
1x USB 2.0 on front and 2x USB 2.0 on rearside
1x LAN RJ45
Cables included in basic unit
Connections
Cable
PRIMERGY TX150 S4
1.
IDE CD/DVD
¡
¡
¡
Key:
¥
68pins
2.
Backplane for 1x4
¥
68 or 50pins
SCSI hard disks
¥
¥
¥
¥
¡
IDE
incl. terminator
terminator
A
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 6 of 18

System configurator and order-information guide
A
PRIMERGY TX150 S4 Status 25.11.2005
Floorstand version SCSI basic unit 19" Rack version SCSI basic unit (5 U)
Pentium 4 processor, memory Pentium 4 processor, memory
PD 820 2.8GHz/800MHz/2x1MB 512MB S26361-K999-V136 PD 820 2.8GHz/800MHz/2x1MB 512MB S26361-K999-V336
PD 820 2.8GHz/800MHz/2x1MB 1GB S26361-K999-V146 PD 820 2.8GHz/800MHz/2x1MB 1GB S26361-K999-V346
PD 820 2.8GHz/800MHz/2x1MB 2GB S26361-K999-V156 PD 820 2.8GHz/800MHz/2x1MB 2GB S26361-K999-V356
S26113-F483-E1 floorstand S26113-F483-E1
hot plug power supply upgrade option versions hot plug power supply upgrade option
With this option the basic units contains A second, redundant With this option the basic units contains
1 hot plug power supply, 1 power power supply requires 1 hot plug power supply, 1 power
backplane and 1 dummy cover an additional power backplane and 1 dummy cover
replacing the standard power supply cord replacing the standard power supply
(no redundancy !) (section XII) (no redundancy !)
max. 1x per system max. 1x per system
S26113-F483-E11 S26113-F483-E11
2nd power supply module (PSU) 2nd power supply module (PSU)
for redundancy for redundancy
occupies one bay for occupies one bay for
hot plug power supply hot plug power supply
max. 1x per system max. 1x per system
For later conversion of basic units with standard power supply
to hot plug power supply, the following kit is available:
1.) hot plug PS upgrade kit, incl. 2 PS module: S26113-F483-L1
Conversion standard into hot plug PS
2.) Supplementary power supply module S26113-F483-L11
for redundancy or repair
B1 B2
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 7 of 18

System configurator and order-information guide
B1 B2
PRIMERGY TX150 S4 Status 25.11.2005
PRIMERGY Floorstand PRIMERGY Rack
PRIMECENTER- Rack
SNP:SY-F1647E301-P "rack-mounting ex factory"
Installation ex works for one This service is to be ordered once
server or subsystem per installable server/storage
Hereby the rack will be delivered subsystem, in order to get the
completely pre-mounted and server/storage subsystem
all wired connections are tested mounted into the PRIMERGY racks.
With racks 12U, 24U, 38U: In case of the 46 U PRIMERGY rack,
Systems and components this service has to be ordered,
will be delivered installed in the rack to get the mounting kits and the
With racks 46U: cables installed.
Systems and components
will be delivered separately
To be ordered only together with
a PRIMERGY-
PRIMECENTER rack
e.g.:SNP:SY-K614V10x-P
S26361-K826-V10x
refer configurator PC-rack
max. 1x per System
For later conversion of TX150 base unit floorstand into base unit rack the following kit is availible
1.) Conversion TX150S4 base unit floorstand into base unit rack S26361-F2618-L240
rack mount kit has to be ordered separately
For (later) mounting in racks the following kits are available:
1.) PRIMERGY Classic-rack 42/23U adapter kit: S26361-F1331-L300
incl. cable carrier
2.) PRIMERGY DC- / PC- rack mounting kit: S26361-F2734-L32
incl. DC- PC- bracket, cable managment
3.) PRIMERGY mounting kit for server racks S26361-F2734-L32
conforming to EIA standards EIA-310-D for 19" racks.
C
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 8 of 18

System configurator and order-information guide
C
PRIMERGY TX150 S4 Status 25.11.2005
Section II Processor
Section III Memory
There are 2 memory banks with 2 DIMM slots each.
Single channel memory configuration allow maximum flexibility:
Additional memory can be configured as single memory modules.
Dual channel memory configurations for maximum performance:
For optimum performance memory has to be configured in pairs of memory modules with identical size.
S26361-F3000-E513 S26361-F3000-E514 S26361-F3000-E515
Main memory 512MB Main memory 1GB Main memory 2GB
3x DDR2 533/PC2-4200 ub ECC DDR2 533/PC2-4200 ub ECC DDR2 533/PC2-4200 ub ECC
consisting of one module consisting of one module consisting of one module
occupies one bank occupies one bank occupies one bank
max. 3x per system max. 3x per system max. 3x per system
Section IV Graphics
ATI Rage XL (8MB)
D
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 9 of 18

System configurator and order-information guide
D
PRIMERGY TX150 S4 Status 25.11.2005
Section VAccessible drives
There are 3x 5.25" bays for accessible drives:
- 1x 5.25" bay is occupied by a DVD-/CD- respectively a CD-RW drive
- 2 x 5.25" bays remaining, can be occupied by 2x accessible drives
Setup TX150 S4 by ServerStart is supported with following configurations:
no DVD, no CD:
remote installation only ( PXE service & DHCP server required)
built in CD/DVD:
UNC Network share reachable or USB Floppy or MemoryBird connected
One of the following USB devices must be used for integrating the drivers during installation
process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done:
1) FDD USB (external): external USB FDD (USB cable included) S26391-F264-L226
2) USB Memorybird: Memorybird 256 MB S26391-F6046-L256
Memorybird 1GB S26391-F6046-L24
S26361-F2575-E1
Floppy disk drive 1"
Connector: 26pin
incl. description (Ger/US)
1" * 3.5", anthracite bezel
max. 1x per system
SNP:SY-F2234E1-A S26361-F3148-E1
DVD-ROM ATAPI DVD-RW 16x super multi drive
all formats, DUAL/DL, DVD-RAM
incl. description (Ger/US) only W2K, W3K and Linux
1.6 x 5.25", anthracite bezel 1.6 x 5.25", anthracite bezel
max. 2x per system max. 1x per system
S26361-F3157-E3
Tape drive LTO2HH Ultrium
200GB, 24MB/s, U160 SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
S26361-F2849-E3
Tape drive VXA-2
80GB, 6MB/s, U2W SCSI
Connector: HD68
2x without cable
incl. description (Ger/US)
data and cleaning catridge
1.6 x 5.25", anthracite bezel
max. 2x per system
S26361-F2848-E3
Tape drive DDS Gen5
S26361-F2848-E31 (only for OBDR)
DDS-G5 for One buttom dis. recov.
36GB, 3MB/s, U2W SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning catridge
1.6 x 5.25", anthracite bezel
max. 2x per system
E
2x
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 10 of 18