Fujitsu SH-E514TR1 10 User manual

Fujutsu SH-E514TR1 10 Gigabit Ethernet SmartPro Switch
User Manual

FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his expense.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user authority to operate the equipment.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem Fall
kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo case, puede
requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des interférences
radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze
radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.
VCCI Warning
この装置は、クラス A情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。
この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A
BSMI Notice
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的
對策。
Safety Compliance
Warning: Class 1 Laser Product.
EN: When using a fiber optic media expansion module, never look at the transmit laser while it is powered on.
Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.
FR: Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez jamais directement le port TX
(Tramsmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu’ils sont sous tension.
SFP (Mini-GBIC), XENPAK, and XFP Regulatory Compliance
Networks pluggable optical modules meet the following regulatory requirements:
Class 1.
IEC/EN60825-1:2007 2nd Edition or later, European Standard
FCC 21 CFR Chapter 1, Subchapter J in accordance with FDA and CDRH requirements.
Application of CE Mark in accordance with 2004/108/EEC EMC Directive and the 2006/95/EC Low Voltage
Directives.
UL and/or CSA registered component for North America.
47 CFR Part 15, Class A when installed into products.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
i
Table of Contents
1. Intended Readers.....................................................................................................................................................1
Terms/Usage.................................................................................................................................................................1
Safety Instructions.........................................................................................................................................................1
General Precautions for Rack-Mountable Products......................................................................................................2
Protecting Against Electrostatic Discharge ...................................................................................................................3
2. Product Introduction ...............................................................................................................................................4
3. Getting Started.........................................................................................................................................................5
Recommended Web Browsers......................................................................................................................................5
Connecting to the Switch...............................................................................................................................................5
Login Web-based Management....................................................................................................................................5
4. Web-based Management.........................................................................................................................................7
5. Tool Bar.....................................................................................................................................................................8
Save...............................................................................................................................................................................8
Save Configuration ....................................................................................................................................................8
Tools..............................................................................................................................................................................8
Firmware Upgrade and Backup.................................................................................................................................8
Firmware Upgrade from HTTP...............................................................................................................................9
Firmware Upgrade from TFTP...............................................................................................................................9
Firmware Backup to HTTP.....................................................................................................................................9
Firmware Backup to TFTP ...................................................................................................................................10
Configuration Restore and Backup..........................................................................................................................10
Configuration Restore from HTTP........................................................................................................................10
Configuration Restore from TFTP........................................................................................................................11
Configuration Backup to HTTP ............................................................................................................................11
Configuration Backup to TFTP.............................................................................................................................11
Log Backup..............................................................................................................................................................12
Log Backup to HTTP............................................................................................................................................12
Log Backup to TFTP ............................................................................................................................................12
Ping..........................................................................................................................................................................13
Reset........................................................................................................................................................................13
Reboot System ........................................................................................................................................................14
6. Device Information.................................................................................................................................................15
7. System ....................................................................................................................................................................16
System Information Settings........................................................................................................................................16
Peripheral Settings......................................................................................................................................................16
Port Configuration........................................................................................................................................................16
Port Settings ............................................................................................................................................................16
Port Status ...............................................................................................................................................................17
Error Disable Settings..............................................................................................................................................18
Jumbo Frame...........................................................................................................................................................18
System Log..................................................................................................................................................................19
System Log Settings................................................................................................................................................19
System Log Discriminator Settings..........................................................................................................................20
System Log Server Settings ....................................................................................................................................20
System Log..............................................................................................................................................................21
System Attack Log...................................................................................................................................................21
Time and SNTP...........................................................................................................................................................21
Clock Settings..........................................................................................................................................................22
Time Zone Settings..................................................................................................................................................22
SNTP Settings .........................................................................................................................................................23

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
ii
8. Management...........................................................................................................................................................24
User Accounts Settings...............................................................................................................................................24
SNMP ..........................................................................................................................................................................24
SNMP Global Settings.............................................................................................................................................24
SNMP Linkchange Trap Settings.............................................................................................................................25
SNMP View Table Settings......................................................................................................................................26
SNMP Community Table Settings...........................................................................................................................26
SNMP Group Table Settings....................................................................................................................................27
SNMP Engine ID Local Settings..............................................................................................................................28
SNMP User Table Settings......................................................................................................................................28
SNMP Host Table Settings......................................................................................................................................29
Web .............................................................................................................................................................................30
Session Timeout..........................................................................................................................................................30
File System..................................................................................................................................................................30
9. L2 Features.............................................................................................................................................................32
FDB..............................................................................................................................................................................32
Static FDB................................................................................................................................................................32
Unicast Static FDB...............................................................................................................................................32
Multicast Static FDB.............................................................................................................................................32
MAC Address Table Settings...................................................................................................................................33
MAC Address Table.................................................................................................................................................33
VLAN ...........................................................................................................................................................................34
802.1Q VLAN...........................................................................................................................................................34
VLAN Interface.........................................................................................................................................................35
STP..............................................................................................................................................................................37
STP Global Settings.................................................................................................................................................37
STP Port Settings ....................................................................................................................................................38
STP Global Information............................................................................................................................................40
STP Port Information ...............................................................................................................................................40
Link Aggregation..........................................................................................................................................................40
L2 Multicast Control.....................................................................................................................................................42
IGMP Snooping........................................................................................................................................................42
IGMP Snooping Settings......................................................................................................................................42
IGMP Snooping Groups Settings.........................................................................................................................45
IGMP Snooping Mrouter Settings ........................................................................................................................45
IGMP Snooping Statistics Settings ......................................................................................................................46
Multicast Filtering.....................................................................................................................................................46
10. L3 Features.............................................................................................................................................................48
IPv4 Interface ..............................................................................................................................................................48
IPv6 Interface ..............................................................................................................................................................48
IPv6 Neighbor..............................................................................................................................................................49
11. QoS..........................................................................................................................................................................51
Basic Settings..............................................................................................................................................................51
Port Default CoS......................................................................................................................................................51
Port Scheduler Method............................................................................................................................................52
Queue Settings........................................................................................................................................................53
CoS to Queue Mapping ...........................................................................................................................................54
Advanced Settings.......................................................................................................................................................54
Port Trust State........................................................................................................................................................54
DSCP CoS Mapping................................................................................................................................................55
12. Security...................................................................................................................................................................56

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
iii
Port Security................................................................................................................................................................56
Port Security Global Settings...................................................................................................................................56
Port Security Port Settings.......................................................................................................................................56
Port Security Address Entries..................................................................................................................................57
Traffic Segmentation Settings .....................................................................................................................................57
Storm Control ..............................................................................................................................................................58
13. Monitoring...............................................................................................................................................................60
Utilization.....................................................................................................................................................................60
Device Utilization .....................................................................................................................................................60
Port Utilization..........................................................................................................................................................60
Statistics ......................................................................................................................................................................60
Port...........................................................................................................................................................................61
Port Counters...........................................................................................................................................................63
Counters...................................................................................................................................................................64
Mirror Settings .............................................................................................................................................................65
Device Environment ....................................................................................................................................................66

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
1
1. Intended Readers
This guide provides instructions to install the SH-E514TR1 10 Gigabit Ethernet SmartPro Switch, and how to configure
Web-based Management step-by-step.
Terms/Usage
In this guide, the term “Switch” (first letter capitalized) refers to the SH-E514TR1 switch, and “switch” (first letter lower
case) refers to other Ethernet switches. Some technologies refer to terms “switch”, “bridge” and “switching hubs”
interchangeably, and both are commonly accepted for Ethernet switches.
A NOTE indicates important information that
helps a better use of the device.
A CAUTION indicates potential property damage
or personal injury.
Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential
damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions and precautions that need
to be reviewed and followed.
CAUTION: Only trained and qualified service
personnel should install, replace or perform
maintenance on the Switch.
To reduce the risk of bodily injury, electrical shock, fire, or damage to the equipment, observe the following
precautions.
Observe and follow service markings.
oDo not service any product except as explained in your system documentation.
oOpening or removing covers that are marked with the triangular symbol with a lightning bolt may expose
you to electrical shock.
oOnly a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part or
contact your trained service provider:
oThe power cable, extension cable, or plug is damaged.
oAn object has fallen into the product.
oThe product has been exposed to water.
oThe product has been dropped or damaged.
oThe product does not operate correctly when you follow the operating instructions.
Keep your system away from radiators and heat sources. Also, do not block cooling vents.
Do not spill food or liquids on your system components, and never operate the product in a wet environment. If
the system gets wet, see the appropriate section in your troubleshooting guide or contact your trained service
provider.
Do not push any objects into the openings of your system. Doing so can cause fire or electric shock by shorting
out interior components.
Use the product only with approved equipment.
Allow the product to cool before removing covers or touching internal components.
Operate the product only from the type of external power source indicated on the electrical ratings label. If you
are not sure of the type of power source required, consult your service provider or local power company.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
2
To help avoid damaging your system, be sure the voltage on the power supply is set to match the power
available at your location:
o115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such as
South Korea and Taiwan
o100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan
o230 V/50 Hz in most of Europe, the Middle East, and the Far East
Also, be sure that attached devices are electrically rated to operate with the power available in your location.
Use only approved power cable(s). If you have not been provided with a power cable for your system or for any
AC-powered option intended for your system, purchase a power cable that is approved for use in your country.
The power cable must be rated for the product and for the voltage and current marked on the product's
electrical ratings label. The voltage and current rating of the cable should be greater than the ratings marked on
the product.
To help prevent electric shock, plug the system and peripheral power cables into properly grounded electrical
outlets. These cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter
plugs or remove the grounding prong from a cable. If you must use an extension cable, use a 3-wire cable with
properly grounded plugs.
Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products plugged
into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension
cable or power strip.
To help protect your system from sudden, transient increases and decreases in electrical power, use a surge
suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; route cables so that they cannot be stepped on or tripped
over. Be sure that nothing rests on any cables.
Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local/national wiring rules.
When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe
the following guidelines:
oInstall the power supply before connecting the power cable to the power supply.
oUnplug the power cable before removing the power supply.
oIf the system has multiple sources of power, disconnect power from the system by unplugging all power
cables from the power supplies.
Move products with care; ensure that all casters and/or stabilizers are firmly connected to the system. Avoid
sudden stops and uneven surfaces.
General Precautions for Rack-Mountable Products
Observe the following precautions for rack stability and safety. Also, refer to the rack installation documentation
accompanying the system and the rack for specific caution statements and procedures.
Systems are considered to be components in a rack. Thus, "component" refers to any system as well as to
various peripherals or supporting hardware.
Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and
that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the rack first.
Make sure that the rack is level and stable before extending a component from the rack.
Use caution when pressing the component rail release latches and sliding a component into or out of a rack; the
slide rails can pinch your fingers.
After a component is inserted into the rack, carefully extend the rail into a locking position, and then slide the
component into the rack.
Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not
exceed 80 percent of the branch circuit rating.
Ensure that proper airflow is provided to components in the rack.
Do not step on or stand on any component when servicing other components in a rack.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
3
CAUTION: Never defeat the ground conductor or operate the equipment in
the absence of a suitably installed ground conductor. Contact the
appropriate electrical inspection authority or an electrician if you are
uncertain that suitable grounding is available.
CAUTION: The system chassis must be positively grounded to the rack
cabinet frame. Do not attempt to connect power to the system until grounding
cables are connected. A qualified electrical inspector must inspect completed
power and safety ground wiring. An energy hazard will exist if the safety
ground cable is omitted or disconnected.
Protecting Against Electrostatic Discharge
Static electricity can harm delicate components inside your system. To prevent static damage, discharge static
electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do
so by periodically touching an unpainted metal surface on the chassis.
You can also take the following steps to prevent damage from electrostatic discharge (ESD):
1. When unpacking a static-sensitive component from its shipping carton, do not remove the component from the
antistatic packing material until you are ready to install the component in your system. Just before unwrapping
the antistatic packaging, be sure to discharge static electricity from your body.
2. When transporting a sensitive component, first place it in an antistatic container or packaging.
3. Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads, workbench pads and
an antistatic grounding strap.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
4
2. Product Introduction
Thank you and congratulations on your purchase of SH-E514TR1 10 Gigabit Ethernet SmartPro Switch.
The product blends plug-and-play simplicity with exceptional value and reliability for small and medium-sized business
(SMB) networking. All models are housed in a new style rack-mount metal case with easy-to-view front panel
diagnostic LEDs, and provides advanced features including network security, traffic segmentation, QoS and versatile
management.
Flexible Port Configurations. The Switch is the new generation of Web 10 Gigabit Ethernet Switch series. It
provides a variety of port counts that can operate at up to 10 Gbps wire speed.
Extensive Layer 2 Features. Implemented as complete L2 device, the Switch includes functions such as IGMP
snooping, Spanning Tree, and 802.3ad LACP to enhance performance and network resiliency.
Traffic Segmentation, and QoS. The Switch supports 802.1Q VLAN standard tagging to enhance network security
and performance. The Switch also support 802.1p priority queues, enabling users to run bandwidth-sensitive
applications such as streaming multimedia by prioritizing that traffic in network. These functions allow the Switch to
work seamlessly with VLAN and 802.1p traffic in the network.
Network Security. Storm Control can help to keep the network from being overwhelmed by abnormal traffic. Port
Security is another simple but useful authentication method to maintain the network device integrity.
Versatile Management. The new generation of the Switch provides growing businesses with a simple and easy
management of their network, using a Web-Based management interface that allows administrators to remotely
control their network down to the port level.
In addition, users can utilize the SNMP MIB (Management Information Base) to poll the Switch for information about
the status, or send out traps of abnormal events. SNMP support allows users to integrate the Switch with other third-
party devices for management in an SNMP-enabled environment
Automated Fan Speed. The Switch has a built-in temperature sensor that will measure the internal temperature of
the Switch and then automatically adjust the speed of the fans to either high-speed or low-speed.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
5
3. Getting Started
The Switch can be managed through any port on the device by using the Web-based Management.
Each switch must be assigned its own IP Address, which is used for communication with the Web-based Management
or a SNMP network manager. The PC should have an IP address in the same range as the switch. Each switch can
allow up to four users to access the Web-Based Management concurrently.
After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics
using a web browser.
Recommended Web Browsers
To be able to access the Web-based Management, it is recommended to use one of the following web browsers:
Internet Explorer 11
Firefox 43.0.4
Google Chrome 47.0
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the PC.
Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same
subnet as the switch. For example, if the switch has an IP address of 192.168.1.1, the PC should have an IP address
of 192.x.y.z (where x/y is a number between 0 and 254 and z is a number between 2 and 254), and a subnet mask of
255.255.255.0. Open the web browser and enter 192.168.1.1 (the factory-default IP address) in the address bar. Then
press ENTER.
Figure 3-1 Enter the IP address 10.90.90.90 in the web browser
NOTE: The Switch's factory default IP address is
192.168.1.1 with a subnet mask of
255.255.255.0 and a default gateway of 0.0.0.0.
When the following logon dialog box appears, enter the User Name and Password in the corresponding fields and
click Login.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
6
Figure 3-2 Login Dialog Box
NOTE: The Switch's factory default username is
admin and the default password is admin.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
7
4. Web-based Management
The features and functions of the Switch can be configured for optimum use through the Web-based Management
Utility.
After logged into the Switch, you will see the screen below:
Figure 4-1 Web-based Management
The above image is the Web-based Management screen. The three main areas are the Tool Bar on top, the
Function Tree, and the Main Configuration Screen.
The Tool Bar provides a quick and convenient way for essential utility functions like firmware and configuration
management on the left, and the username with current IP address and the Logout button on the right. Click Logout
to end this session.
NOTE: If you close the web browser without
clicking the Logout button first, then it will be
seen as an abnormal exit and the login
session will still be occupied.
By choosing different functions in the Function Tree, you can change all the settings in the Main Configuration
Screen. The main configuration screen will show the current status of your Switch by clicking the model name on top
of the function tree.
Function Tree
Main Configuration Screen
Tool Bar

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
8
5. Tool Bar
Save
The Save Menu provides the Save Configuration function.
Figure 5-1 Save
Save Configuration
Select to save the entire configuration changes you have made to the device to switch’s non-volatile RAM.
Figure 5-2 Save Configuration
Tools
The Tools Menu offers global function controls Firmware Upgrade & Backup, Configuration Restore & Backup, Log
Backup, Ping, Reset, and Reboot System.
Figure 5-3 Tools Menu
Firmware Upgrade and Backup
Allow for the firmware to be saved, or for an existing firmware file to be uploaded to the Switch. The Switch can only
allow having maximum 2 firmware files saved in the File System. Go to Management > File System to delete the old
firmware files in order to upgrade firmware successfully. The Two methods can be selected: HTTP or TFTP.
Figure 5-4 Tools > Firmware Upgrade and Backup

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
9
Firmware Upgrade from HTTP
This window is used to upgrade the firmware from HTTP.
Figure 5-5 Firmware Upgrade from HTTP
The fields that can be configured are described below:
Source File: Click Browse to browse your inventories for a saved firmware file.
Destination File: Enter the destination filename and path where the new firmware should be stored on the Switch.
This field can be up to 32 characters long.
Click Upgrade after selecting the firmware file you want to restore.
Firmware Upgrade from TFTP
This window is used to upgrade the firmware from TFTP.
Figure 5-6 Firmware Upgrade from TFTP
The fields that can be configured are described below:
TFTP Server IP: Upgrade the firmware from a remote TFTP server. Specify the TFTP server IP address.
Source File: Enter the source filename and path of the firmware file located on the TFTP server here. This field can
be up to 32 characters long.
Destination File: Enter the destination filename and path where the new firmware should be stored on the Switch.
This field can be up to 32 characters long.
Click Upgrade after selecting the firmware file you want to restore.
CAUTION: Do not disconnect the PC or remove
the power cord from the Switch until the upgrade
completes. The Switch may crash if the firmware
upgrade is incomplete.
Firmware Backup to HTTP
This window is used to back up the firmware to HTTP.
Figure 5-7 Firmware Backup to HTTP
The fields that can be configured are described below:
Source File: Enter the source filename and path of the firmware file located on the Switch here. This field can be up
to 32 characters long.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
10
Click Backup to save the firmware to your disk.
Firmware Backup to TFTP
This window is used to back up the firmware to TFTP.
Figure 5-8 Firmware Backup to TFTP
The fields that can be configured are described below:
TFTP Server IP: Backup the firmware to a remote TFTP server. Specify the TFTP server IP address.
Source File: Enter the source filename and path of the firmware file located on the Switch here. This field can be up
to 32 characters long.
Destination File: Enter the destination filename and path where the firmware should be stored on the TFTP server.
This field can be up to 32 characters long.
Click Backup to save the firmware to the TFTP server.
Configuration Restore and Backup
Allow the current configuration settings to be saved to a file (not including the password), and if necessary, you can
restore the configuration settings from this file. The Switch can only allow having maximum 2 configuration files saved
in the File System. Go to Management > File System to delete the old configuration files in order to restore
configurations successfully. Two methods can be selected: HTTP or TFTP.
Figure 5-9 –Tools > Configure Restore and Backup
Configuration Restore from HTTP
This window is used to restore the configuration from HTTP.
Figure 5-10 Configuration Restore from HTTP
The fields that can be configured are described below:
Source File: Click Browse to browse your inventories for a saved firmware file.
Destination File: Enter the destination filename and path where the configuration file should be stored on the Switch.
This field can be up to 32 characters long. Select the running-config option to restore and overwrite the running
configuration file on the Switch. Select the startup-config option to restore and overwrite the start-up configuration file
on the Switch.
Replace: Replace the current running configuration.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
11
Click Restore after selecting the backup settings file you want to restore.
Configuration Restore from TFTP
This window is used to restore the configuration from TFTP.
Figure 5-11 Configuration Restore from TFTP
The fields that can be configured are described below:
TFTP Server IP: Restore the configuration from a remote TFTP server. Specify the TFTP server IP address.
Source File: Enter the source filename and path of the configuration file located on the TFTP server here. This field
can be up to 32 characters long.
Destination File: Enter the destination filename and path where the configuration file should be stored on the Switch.
This field can be up to 32 characters long. Select the running-config option to restore and overwrite the running
configuration file on the Switch. Select the startup-config option to restore and overwrite the start-up configuration file
on the Switch.
Replace: Replace the current running configuration.
Click Restore after selecting the backup settings file you want to restore.
Configuration Backup to HTTP
This window is used to back up the configuration to HTTP.
Figure 5-12 Configuration Backup to HTTP
The fields that can be configured are described below:
Source File: Enter the source filename and path of the configuration file located on the Switch here. This field can be
up to 32 characters long. Select the running-config option to back up the running configuration file from the Switch.
Select the startup-config option to back up the start-up configuration file from the Switch.
Click Backup to save the current settings to your disk.
Configuration Backup to TFTP
This window is used to back up the configuration to TFTP.
Figure 5-13 Configuration Backup to TFTP
The fields that can be configured are described below:
TFTP Server IP: Back up the configuration from a remote TFTP server. Specify the TFTP server IP address.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
12
Source File: Enter the source filename and path of the configuration file located on the switch here. This field can be
up to 32 characters long. Select the running-config option to back up the running configuration file from the Switch.
Select the startup-config option to back up the start-up configuration file from the Switch.
Destination File: Enter the destination filename and path where the configuration file should be stored on the TFTP
server. This field can be up to 32 characters long.
Click Backup to save the current settings to the TFTP server.
Log Backup
Allow the logs to be saved to HTTP or TFTP.
Figure 5-14 –Tools > Log Backup
Log Backup to HTTP
This window is used to back up the logs to HTTP.
Figure 5-15 Log Backup to HTTP
The fields that can be configured are described below:
Log Type: Select the log type that will be backed up to the local PC using HTTP. When the System Log option is
selected, the system log will be backed up. When the Attack Log is selected, the attack log will be backed up.
Click Backup to save the current settings to your disk.
Log Backup to TFTP
This window is used to back up the logs to TFTP.
Figure 5-16 Log Backup to TFTP
The fields that can be configured are described below:
TFTP Server IP: Back up the log from a remote TFTP server. Specify the TFTP server IP address.
Destination File: Enter the destination filename and path where the log file should be stored on the TFTP server. This
field can be up to 32 characters long.
Log Type: Select the log type that will be backed up to the TFTP server. When the System Log option is selected,
the system log will be backed up. When the Attack Log is selected, the attack log will be backed up.
Click Backup to save the current settings to the TFTP server.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
13
Ping
Ping is a small program that sends ICMP Echo packets to the IP address you specify. The destination node then
responds to or “echoes” the packets sent from the Switch. This is very useful to verify connectivity between the Switch
and other nodes on the network.
Figure 5-17 Ping
The fields that can be configured are described below:
Target IPv4 Address / Target IPv6 Address: Enter an IPv4 or IPv6 address to be pinged.
Ping Times: Enter the number of times desired to attempt to Ping the IPv4 or IPv6 address. Users may enter a
number of times between 1 and 255. Tick Infinite to keep sending ICMP Echo packets to the specified IPv4 or IPv6
address until the program is stopped.
Timeout: Select a timeout period between 1 and 99 seconds for this Ping message to reach its destination. If the
packet fails to find the IPv4 or IPv6 address in this specified time, the Ping packet will be dropped.
Click Start to initiate the Ping Test for each individual section.
After clicking Start, the Ping Result section will appear:
Figure 5-18 –Ping Result
Click Stop to halt the Ping Test.
Click Back to return to the IPv4 or IPv6 Ping section.
Reset
Provide a safe reset option for the Switch.

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
14
Figure 5-19 Reset
Select the The Switch will be reset to its factory defaults including IP address, and then will save and reboot.
option to reset the Switch’s configuration to its factory default settings.
Select the The Switch will be reset to its factory defaults except IP address, and then will save and reboot
option to reset the Switch’s configuration to its factory default settings. This option will exclude the IP address from
being changed.
Select the The Switch will be reset to its factory defaults including IP address option to reset the Switch’s
configuration to its factory default settings.
Click Apply to initiate the factory default reset and reboot the Switch.
Reboot System
Provide a safe way to reboot the system. Click Yes and Apply to restart the Switch.
Figure 5-20 Reboot Device

SH-E514TR1 10 Gigabit Ethernet SmartPro Switch User Manual
15
6. Device Information
This window displays the Device Information. It appears automatically when you log in the Switch. To return to the
Device Information window after viewing other windows, click SH-E514TR1 in the Function Tree.
Figure 6-1 –Device Information