Fuling Inverter DZB200 Series User manual

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 1/54

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 2/54

目 录
Appendix A Standard Specifications 82
Appendix B Serial Communications 85
Appendix C Dimensions 98
Appendix D Accessories List 100
1
Chapter 1 Safety and Cautions
7Chapter 3 Mechanical and Electrical Installation
6
Chapter 2 Product Introduction
17
Chapter 4 Operation and Display
22
Chapter 5 Function Parameters List
34
Chapter 6 Parameter Description
73
Chapter 7 Fault Diagnosis and Countermeasures
81
Chapter 8 Quality Guarantee
F0 Basic Function Parameters 34
F1 Motor Parameters 42
F2 Input and Output Terminal Function Parameters 46
F3 Human Machine Interface Parameters 54
F4 Application Function Parameters 57
F5 Protection Parameters 66
F6 Communication Parameters 69

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 3/54

-1-
Preface
DZB DZB200&300T hank you f or cho os in g hig h -perf orm ance A C Motor Driv es .
Series are manufactured by adopting high-q uality components, material and incorporating
the latest microprocessor technology available.
Getting Started
This manual will be helpful in the installation, parameter setting, troubleshooting, and
daily maintenance of the AC motor drives. To guarantee safe operation of the equipment,
read the following safety guidelines before connecting power to the AC drives. Keep this
operating manual handy and distribute to al l users for reference.
Series
ATTENTION:
DANGER!
WARNING!
WARNING!
ATTENTION:
CAUTION:
CAUTION:
CAUTION:
Always read this manual thoroughly before using series AC Motor Drives.
AC input power must be disconnected before any maintenanc e.
Do not connect or disconnect wires and connectors while power is applied tothe circuit.
Maintenance must be performed by qualified technicians.
To avoid personal injury, do not remove the co ver of the AC motor drive until all of the
digital keypad "DISPLAY LED" lamps are off. The DC-link capaci tor remains charged
with a hazardous voltage even after input power is removed.
Grounding the DZB100B drive i s done by
.
There are highly sensitive component s on the printed circuit boards. These components are
especial ly sensitive t o E SD (ele ctrostatic disch arge). ,do not
touch components or the circuit boards until sta tic control precautions have been taken.
Never connect the main circuit output terminal s U, V, and W directly to the AC main circuit
power supply as .
Do not apply the antirust to screws for fast ening drives; Please clean the drives and screws
with dry cloth or alcohol, not with synthetic cleaner. Fasten the screws with washers and
rated torque lest the enclosure corners of d rives be distorted.
DZB
connecting the Earth Ground to the drive
ground terminal
To avoid damage to the drive
this will damage the drive
This manual is for DZB200&DZB300 SeriesAC M otor Drive.
Preface
DZB Series
!WARNING

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 4/54

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 5/54

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 6/54


5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 7/54
Chapter 3 Mechanical and Electrical Installation
3. 1 Mechanical Installation
1) Ambient temperature: Ambient temperature influences the inverter life greatly, so it should be within
the range of -10 ~50 .
2) Mount the inverter in a flame retardant s urface and the clearance around the inverter shall be enough
because the inverter will generate lots of heat during runni ng, besides mount the inverter on the base
vertically with screws.
3) Mount in the location where vibration is le ss than 0.6G; the inverter shall be far away from impact ing
lathe.
4) Please do not install the inverter in the place with direct sunlight, high humidit y and water.
5) Mount the inverter in the location free o f corrosive gas, explosive gas or combustible gas.
6) Mount the inverter in the location free of oi l dirt, dust, and metal powder.
1. Installation Environment
2.Installation Location
℃ ℃
D Z B
up
right
A
≥100mm
≥100mm
A
D Z B
D Z B
Note: No need to consider the dimension
A for inverter of 22kW or below.
A shall be bigger than 50mm for the
inverter of 22kW or above
Note: Install an airflow- guidance
plate for the up and down installation
of inverters.
Fig.3-1 DZB Series Inverter Installation Location
The user shall focus on the heat dissipation issues when installing the inverter, and pay attention to the
following points:
1) Install the inverter vertically so th at the heat may be expelled from the top, but do not install the
inverter upside down. When two Variable Speed Drives are mou nted up and dow n, an air flow
diverting plate should be fixed in between as shown in Fig. 3-1.
2) Installation space is shown in Fig.3-1 so as to ensur e the heat dissipation space, but consider the
heat dissipation of other components when placing the i nverter.
3) The installation bracket must be flame retardant.
4) Install the heat sink outside of the cabinet if the i nverter is installed in the area with metal powder.
And in this case, the space inside the sealing cabi net shall be big enough.
Nameplate
D Z B 3 0 0 B0015 L4 A
Function level code: A -braking unit inside
B -non braking unit
Input voltage
Freq. Range
Applicable motor capacity
Series General-Purpose Model
Fan&Pump Model
Seri es name Serie s
2-220V 4-400V 6-660V
L 0-600.0Hz
0015 1.5KW
B:
P:
: DZB300
：
： ：
： 为
：
Description ofACMotor Drive Model:
Production number
Production month
Production year
8 8 8 81 00 6
Description of Serial Number::
2.2 Nameplate Information
- 7 - - 8 -
Install at ion of s i ng le i nv erter Up and down i nstal lation of i nv erters
Chapter 2 Product Introduction
DZB Series Chapter 3 Mechanical and Electrical Installation DZB Series


5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 8/54
3.2 Electrical Installation
1.Applicable devices and recommendable wiring of main circuit:
0005L2
0007L2
0015L2
0022L2
0037L2
0007L4
0015L4
0022L4
0037L4
0055L4
0075L4
0110L4
0150L4
0185L4
0220L4
0370L4
0450L4
0300L4
0550L4
0750L4
0930L4
1100L4
1320L4
1600L4
1870L4
2000L4
2200L4
2500L4
2800L4
3150L4
4000L4
5000L4
6300L4
0.55
0.75
1.5
2.2
3.7
0.75
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
93
110
132
160
187
200
220
250
280
315
400
500
630
70
*
2(150)
95*2(185)
120*2(240)
150*2(300)
185*2(370)
185*2(370)
INPUT(RST)
Air Circuit
Breakers
MCCB
Wire Size(mm )
2
Control
Terminal
0.5
0.75
DZ20-630(500A)
DZ20-630(600A)
DZ20-400(400A)
DZ20-400(350A)
DZ20-400(250A)
DZ20-200(200A)
DZ20-100(100A)
DZ20-100(80A)
DZ20-100(63A)
DZ20-100(50A)
DZ20-100(32A)
DZ20-100(16A)
DZ20-100(32A)
DZ20-100(16A)
DZ20-800(800A)
DZ20-1250(1000A)
DZ20-1250(1250A)
Magnetic
Contactor
MC
Applicable
Motor
(KW)
MODEL
DZB300
Series
CJ20-16
CJ20-40
CJ20-16
CJ20-40
CJ20-63
CJ20-100
CJ20-160
CJ20-250
CJ20-400
CJ20-630
CJ20-800
CJ20-500*2
CJ20-630*2
Power
Terminal
1.5
2.5
4
4
1.5
2.5
4
1.5
2.5
4
1.5
2.5
4
4
6
6
6
6
88
10
10
16
16
16
25
25
25
35
16
*
2(35)
25*2(50)
25*2(50)
25*2(50)
35*2(70)
35*2(70)
35*2(70)
50*2(95)
50*2(100)
50*2(95)
50*2(100)
70
*
2(150)
70*2(150)
95*2(185)
120*2(240)
150*2(300)
185*2(370)
185*2(370)
DC
Reactor Breaking Terminal
- 9 - - 1 0 -
2. Wiring Diagram of Peripheral Equipment
Pow er Supply
Breaker or
Leakage Sw itch
M agnetic
Contactor( M C)
Input AC
Reactor(AC)
InputSide
Interference
Filter
Braking Resistor
Pow er-factor-im proving
D C Reactor(D C)
G rounding
Inverter
O utput AC
Reactor(AC)
O utput Side
N oise Filter
M otor
G rounding
Chapter 3 Mechanical and Electrical Installation
DZB Series
Chapter 3 Mechanical and Electrical Installation
DZB Series

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 9/54

5/14/2018 Fuling Inverter User Manual - slidepdf.com
http://slidepdf.com/reader/full/fuling-inverter-user-manual 10/54