Funkey FK-9659 User manual

ENGINE SIZE:30
GENERAL INSTALLATION MANUAL
NOTICE: USE EPOXY UNLESS STATED.
SAND INSIDE FUSELAGE WITH #180 SANDING
PAPER BEFORE PARTS GLUING IN PLACE.
AGUSTA A109
2
4
5
7
3
1
6
8
P.1
GLUE 2 PCS MANIFOLDS ON FUSELAGE AS SHOWN.
CUT THE MESH AND GLUE IT AT THE BACK
OF COOLING VENTS WITH CA.
BALL LINK
MOUNT THE NOSE LANDING GEAR WITH 3 X 12 MM
ROUND SOCKET HEAD SCREWS AND LOCK NUTS.
GLUE 8 X 32 MM PLYWOOD INSIDE FUSELAGE.
M2 X 36 THREADED PUSH ROD
MOUNT THE MAIN LANDING GEAR WITH
2.6 X 12 MM FLAT HEAD TAPPING SCREW.
BALL LINK
M2 X 70 THREADED PUSH ROD

ENGINE SIZE:30
GENERAL INSTALLATION MANUAL
AGUSTA A109
P.2
10
12
13
15
11
9
14
16
NOSE WHEEL (35 MM) MAIN WHEEL (40 MM)
GLUE 4 PCS. OF
3 X 10 X16 MM PLYWOOD
AND DRILL 3MM HOLES AT B.
GLUE 8 PCS.
OF 3 X 10 X10 MM
PLYWOOD AT A.
A
B
DRILL 3MM HOLES AT D.
(LOCATION OF D MUST BE MATCHED
WITH A IN STEP11.)
C
GLUE 4 PCS. OF 3 X 10 X 16 MM PLYWOOD AT C.
AND DRILL 3 MM HOLES AND INSTALL 3 MM ALUN.
POLES AT C FOR FRONT AND REAR ALIGNMENT.
(LOCATION OF C MUST BE MATCHED
WITH B IN STEP 11.)
FASTEN FRONT AND REAR PORTION OF
FUSELAGE WITH 8 PCS. OF 3 X 6 MM
ROUND HEAD TAPPING SCREWS AT D.
ALIGN HORIZONTAL STAB.AND GLUE
D
A
A
A
A
A
A
A
B
BB
D
D
D
D
D
D
D
C
C
C
FASTEN FRONT AND REAR PORTION OF
FUSELAGE WITH 8 PCS. OF 3 X 6 MM
ROUND HEAD TAPPING SCREWS AT D.

P.3
ENGINE SIZE:30
GENERAL INSTALLATION MANUAL
AGUSTA A109
18
20
21
19
17
22
GLUE 2 PCS. OF 1.5 X 10 X 10 MM PLYWOOD. MOUNT TAIL HATCH WITH 2 PCS.
OF M3 X 6 ROUND HEAD TAPPING SCREW.
GLUE RED LIGHT & ALUM. LIGHT HOLDER
ON TOP OF FUSELAGE.
* "GOOP" IS A BRAND OF GLUE WHICH IS MANUFACTURED BY ECLECTIC
PRODUCTS, INC. IT IS AVAILABLE IN MOST HARDWARE STORES.
GLUE WINDSHIELD OUTSIDE
FUSELAGE WITH "GOOP" *.
CUT WINDSHIELD
AND WINDOWS
AS MARKED.
GLUE TOP WINDOWS INSIDE
FUSELAGE WITH "GOOP" *.
GLUE CLEAR LIGHT & ALUM. HOLDER ON TAIL HATCH
GLUE RED LIGHT & ALUM. LIGHT HOLDER ON
BOTTOM OF FUSELAGE

240 MM 40
MM
139 MM
55 MM 71.5 MM
50
MM
2
4
5
7
3
1
6
8
AGUSTA A109 ENGINE SIZE:30
INSTALLATION OF HIROBO SHUTTLE MECHANISM
P.4
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
INSTALL ALUM. MOUNTING PLATES WITH
3 X35 MM SOCKET HEAD SCREW AND
LOCKNUT AS SHOWN.
GLUE 3MM SHAPED PLYWOOD
INSIDE FUSELAGE
CUT HOLE FOR STARTING PROBE.
MOUNTING MECHANISM IN FUSELAGE WITH
3.5 X 15 X 4 MM PLASTIC SPACERS IN PLACE.
FASTEN ALUM. MOUNTING PLATE WITH M 3 X 10 FLAT
HEAD SCREWS AND LOCKNUTS.
USE A SMALLER SIZE MUFFLER.
FOR EXAMPLE: HIROBO PARTS NO. 0402-050
AFTER GLUE THE FRP STABILIZER IN FUSELAGE SLOT AND
INSTALL MECHANISM W/ TAIL BOOM IN PLACE, PUT THE
BOOM HOLDER WOOD PARTS INSIDE FUSELAGE (ON TOP
OF STABILIZER AS SHOWN ABOVE). DO NOT GLUE THE
WOOD PARTS OTHERWISE THE TAIL BOOM CANNOT BE
TAKEN IN AND OUT.

AGUSTA A109 ENGINE SIZE:30
INSTALLATION OF HIROBO SHUTTLE MECHANISM
10
12
13
15
11
9
14
16
P.5
VIEW AT LEFT.INSERT TAIL GEAR-BOX WITH TAIL BOOM INTO
FUSELAGE.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN
AT RIGHT SIDE.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN
AT LEFT SIDE.
LOCATION OF TAIL BOOM HOLDER WOOD PARTS
AND FRP STABILIZER INSIDE FUSELAGE.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN
AT BOTTOM.
VIEW AT BOTTOM.
VIEW ATRIGHT .

AGUSTA A 109
ENGINE SIZE: 30
Below optional retractable landing gears
are available for this helicopter.
Manufactured BY:FUN-KEY AEROPLANE MODELS & BALSAWOOD MFR.
PARTS NO. FK-9659
NOSE GEARMAIN GEAR