Furmanac Ottoman bed User manual

ASSEMBLY INSTRUCTIONS
Easy set up instructions
for your new ottoman bed
THIS INSTRUCTION PACK IS UNIVERSAL ACROSS THE RANGE
THE IMAGE USED MAYBE DIFFERENT FROM THE ONE IN PACK
MANUAL
OTTOMAN
VERSION 11
Correct at time of publication 11/08/22
BOM CODE - LEAFLET - OT-T2-V2

1. Unpack in the room the bed is intended to be used,
remove all packaging and dispose of carefully,
keeping polythene out of the reach of children.
CONTENTS:
• • 1 x Headboard
• • 2 x Side Rails
• • 1 x Foot board
• • 2 x Baseboards
• • 2 x Slatted Frames (pre slatted)
• 3 x Hex Bolts, Washers & Nu
•
•
2 x Brace Bars
• • 4 x M6 Flange Nuts
•• 1 x Fabric Strap
SAFETY FEATURES:
DANGER – RISK OF INJURY / CRUSHING
Introduction
and components
2
The ottoman must only be operated by responsible and capable adults.
Never allow children to operate the ottoman.
ENTRAPMENT
DANGER
ENTRAPMENT
DANGER
TOOLS REQUIRED
The following tools are required for this assembly
1 x Socket Set - 13mm (Ratchet) Spanner
1 x Cross Head Screwdriver (also known as a Phillips)
CAUTION WITH ASSEMBLY
Some stages of this Bed Assembly will require two
people to hold and lift components that maybe heavy.
The slatted frame MUST have the mattress in place to close. Without the weight of
the mattress will result in damage to the bed.
•
•

3
CONTENTS
This product is HEAVY, it should be assembled as near as possible to the point of use.
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes
approximately 60-90 MINUTES to assemble with 2 PEOPLE.
The ttings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaet in full before commencing assembly.
Please check the pack contents before attempting
to assemble this product.
If any components are missing, please contact the retailer
from whom you bought this product.
NEW CONSTRUCTION
POWER OTTOMAN
LEG-SQUAREBUN-DC7-110-KIERRA = x2
(FOR HEADBOARD & FOOTBOARD
CENTRE SUPPORT)
40 = x6
(2x FOR DC7 FIXING,
4x FOR BASEBOARD SUPPORT BLOCK) BUTS17-OT = x2
(FROM MILL CUT IN HOUSE,
SOFTWOOD 60x45x45mm)
MOTOR-OKIN-3.00.401.126.30 = x1
DC Power
MOTOR-OKIN-83458 = x1
FIXING-BOLT-M8X50-HEX-FULL = x4
(FOR STATIC TO HINGE)
Ottoman
OTTOMAN
ASSEMBLY
INSTRUCTIONS
Made in England
NO CODE - PRINTED IN HOUSE
POWER OTTOMAN INSTRUCTIONS
FIXING-NUTP-M8 = x4
(FOR STATIC TO HINGE)
MOTOR-OKIN-3.00.402.026.30 = x1
BATTERY-9V = X2
NEW CONSTRUCTION
POWER OTTOMAN
LEG-SQUAREBUN-DC7-110-KIERRA = x2
(FOR HEADBOARD & FOOTBOARD
CENTRE SUPPORT)
FIXING-SCREW-4.0X40 = x6
(2x FOR DC7 FIXING,
4x FOR BASEBOARD SUPPORT BLOCK) BUTS17-OT = x2
(FROM MILL CUT IN HOUSE,
SOFTWOOD 60x45x45mm)
MOTOR-OKIN-3.00.401.126.30 = x1
DC Power
MOTOR-OKIN-83458 = x1
FIXING-BOLT-M8X50-HEX-FULL = x4
(FOR STATIC TO HINGE)
Ottoman
OTTOMAN
ASSEMBLY
INSTRUCTIONS
Made in England
NO CODE - PRINTED IN HOUSE
POWER OTTOMAN INSTRUCTIONS
FIXING-NUTP-M8 = x4
(FOR STATIC TO HINGE)
MOTOR-OKIN-3.00.402.026.30 = x1
BATTERY-9V = X2
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
FIXING - POZIPAN
M6X40mm= x4
BRACE-BAR
= x2
FIXING-NUT FLANGE
M6-HEX = x4
FIXING-BOLT-
M6X40mm = x4
FIXING-WASHER
M6X20mm = x6
ASSEMBLY GUIDE
= x1
FIXING-NUT
M6 = x3
FIXING-BOLT-
M6X70mm = x3
SOFTWOOD CUBE
60x45x45mm) = x2
FABRIC HANDLE
= x1
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
OTTOMAN-FRAME
(Packing Bag)
FIXING-NUTFLANGE-M6-HEX-S = x4 FIXING-BOLT-M6X40-SOCKET-CSK = x4
FIXING-NUTP-M6 = x3
FIXING-WASHER-M6X20 = x6
FIXING-BOLT-M6X70 = x3
STATIC FRAME CODES
OTTOMAN-FRAME-V1-60
OTTOMAN-FRAME-V1-50
OTTOMAN-FRAME-V1-46
OTTOMAN-FRAME-V1-CONNECTING-BAR = x2
FIXINGS TO BE PACKED INTO RED PACKING BAG AND KNOTTED
TO THE STATIC FRAME
CHECK LIST - BED ASSEMBLY
CHECK LIST - FRAME ASSEMBLY
Ottoman
OTTOMAN
ASSEMBLY
INSTRUCTIONS
Made in England

5
The hinge brackets will already be fixed into place.
Please Note: You are required to follow the steps as detailed
to make sure that the bed is correctly set up.
Left Hand Bracket 4.
1 . Remove the M8 Nut on position A
2 . Move the gas strut into the position A
3 . Place the M8 Nut and tighten with 13mm Spanner
5.
1 . Remove the M8 Nut on position B
2 . Move the gas strut into the position B
3 . Place the M8 Nut and tighten with 13mm Spanner
Right Hand Bracket
A
B

Please Note: this step
will require two people
and requires lifting.
PULL
TOGETHER
LATCH
ONTO BRACKET
TIGHTEN
WITH SPANNER
6. Connect the side rails to the head board
sliding the bolts into the brackets and tightening
with spanner or appropriate socket set.
7. Lower the support bar into the
middle section of the bed.
8. Connect the foot board to both
of the side rails by sliding the bolts
into the brackets and tightening with
spanner or appropriate socket set.
PULL
TOGETHER
LATCH
ONTO BRACKET
TIGHTEN
WITH SPANNER
6
SUPPORT BAR
HEAD BOARD
FOOT BOARD
** Do not tighten bolts to one side until step 7 below.

Please Note: this step
will require two people
and requires lifting.
10. Lower the second base board into place with
the angled cut corners against the head board
(as shown below).
7
9. Lower the first base board into place with the
angled cut corners against the head board
(as shown above).

Please Note: this step
will require two people
and requires lifting.
8
11. With help, lower the slatted base onto the
two rails (attached to the hinge). Make sure
that the welded retaining brackets are at the
headboard end.
Please Note: The hinge bracket has
been pre-threaded.
12. Using the 4 x M8 Bolts, attach the
slatted frame to each of the hinge brackets;
2 x M8 Bolts to each hinge.

Please Note: this step
will require two people
and requires lifting.
13. Lower your mattress onto
the slatted frame.
14. Loop the fabric strap to the frame.
9
ENTRAPMENT
DANGER
ENTRAPMENT
DANGER
Danger – Risk of Injury / Crushing
The ottoman must only be operated by responsible and capable adults.
Never allow children to operate the ottoman. The mattress must be in place
before attempting to close your bed.
YOUR BED WILL ONLY LOWER ONCE THE MATTRESS IS IN PLACE
** Recommended mattress weight
to be at least 45kg to allow for
pistons to work properly.

Guarantee T&Cs
Please note:
This guarantee is a back to base guarantee and we are not obliged to
repair or replace our product in the end user’s premises.
This guarantee is valid from date of delivery to our customer’s address
and we reserve right at our discretion to repair or replace any parts that
are faulty subject to the following conditions;
• The product has only being used for domestic use
• The original proof of purchase can be provided
• The product has remained with the original owner and has not been
resold or gifted
• The product has been used in accordance with the care and safety
guidelines outlined in this document
•The product has not been modied or attempted to be repaired by
any person not authorised by Furmanac
• For the complete terms and conditions please visit
www.furmanac.com
Making a Claim
• The Contract of Sale exists between you and the retailer. Consequently, if you have any
concerns, please contact your retailer in the rst instance, giving proof of purchase and
outlining the nature of your query. If the warranty conditions have been satised, the retailer
will then liaise with Furmanac on your behalf. Any replacement, repair or refund during this
period can only be obtained from your retailer under their terms and conditions of sale.
• For electrical manufacturing faults within 7 years, Furmanac will provide replacement parts to
the retailer in to be able to repair the bed. For other manufacturing faults within 7 years, we
will discuss with the retailer whether a repair by a Furmanac technician or replacement will be
offered. Whether your Furmanac bed is repaired or replaced will be at our sole discretion.
•If you nd that the retailer you purchased your bed from is no longer in business then please
call 01384 408844. Please have details regarding date of purchase, product name and size
along with details of the retailer prior to contacting us. Our dedicated service team will then
be able to advise you accordingly.
Your Furmanac Guarantee
We are delighted that you have bought one of Furmanac’s British, quality hand made beds.
Don’t forget, to obtain the full, 7 year guarantee you must register your product online. To do
this, please visit www.furmanac.com/registermyguarantee and complete the online form within
30 days of delivery to your address.
Your upholstered bed frame is provided with a standard 1 Year Guarantee, protecting you
against manufacturing defects. When you register for your guarantee online this will be
extended to our 7 Year Guarantee. If you feel that your product has developed a fault within
your guarantee period then please follow the process below. However, prior to starting this
procedure Furmanac strongly recommends reviewing all the information on the following pages
to conrm that the issue is in fact a manufacturing fault.
10

Upholstery Care Guide
This guarantee does not cover the general wear and tear of fabrics. Any claims for upholstery faults
outside the realms of general wear and tear. Please ensure the following guidelines have been adhered
to as failure to do so will invalidate your guarantee.
Major cleaning of fabric must be conducted by an upholstery specialist
A multitude of fabrics consisting of different materials, bres and constructions make up the Furmanac
swatches. As a result of this it is difcult to provide generalised cleaning instructions, therefore it is
recommended that any major cleaning is conducted by an upholstery specialist.
Minor stains
Some stains can be removed by means of a damp (not over wet) cloth and soapy water or mild
detergent if necessary. It is recommended that any chemicals are pretested in an inconspicuous area of
the product. After cleaning the test area please check the compatibility of the fabrics used, specically
monitoring if any colours have faded or any shrinkage has occurred. If a ring remains around the stain
after cleaning, you’ll need to deep clean the entire product. For more stubborn stains, please consult a
professional cleaning company.
Third Party Treatments
Furmanac will not accept liability for upholstery problems caused by any third parties when applying
fabric protection.
Fabric Fading
To reduce fabric fading avoid letting direct sunlight on product by using blinds or curtains.
Spillages
In the event of a spillage the surface must rst be blotted dry with an absorbent colour fast cloth or plain
kitchen roll. Avoid using coloured towels or printed paper towels as they may transfer dye or ink to the
upholstery.
• DO NOT apply excessive pressure / rub the spillage as this could permanently damage the fabric.
• If a large amount is spilled, remove as much as possible with clean towelling, a scraper or spoon; blot
up the rest, then treat any remaining stains in the same manner as a minor clean.
• Please note fabrics with a high cotton content are at risk of becoming lighter after spot cleaning.
Pile Crush
All pile fabrics, including Chenilles, are subject to a certain degree of shading or ‘pile crush’. This is not a
fabric fault, but the effect of ‘pile crush’ can be minimised (not eliminated) by using a soft brush to lightly
brush the pile in a different direction over areas that show signs of wear.
Additional Warning
ENTRAPMENT
DANGER
ENTRAPMENT
DANGER
Danger – Risk of Injury / Crushing
The ottoman must only be operated by responsible and capable adults.
Never allow children to operate the ottoman. The mattress must be in place
before attempting to close your bed.
11
VERSION 10
Correct at time of publication 17/03/22